- 16 10月, 2007 7 次提交
-
-
由 Keita Maehara 提交于
These patches enable a few YMF743 controls (Tone/3D/IEC958) that won't be detected with the current version of ALSA. The second one contains following changes: - A chip-specific SPDIF support for YMF743 (It doesn't have AC97 standard SPDIF registers seen on YMF753). - The implementation for 'IEC958 Playback Source' and 'IEC958 Mute' are identical to the ones for YMF753. But there is no 'IEC958 Output Pin' for YMF743. Signed-off-by: NKeita Maehara <maehara@debian.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Keita Maehara 提交于
These patches enable some YMF743 controls (Tone/3D/IEC958) that won't be detected with the current version of ALSA. The first one contains only cosmetic changes to share a few YMF753-specific symbols with YMF743. Signed-off-by: NKeita Maehara <maehara@debian.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Takashi Iwai 提交于
Added CONFIG_SND_AC97_POWER_SAVE_DEFAULT and CONFIG_SND_HDA_POWER_SAVE_DEFAULT Kconfig options as the default values for power-saving mode of AC97 and HD-audio drivers, respectively. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Takashi Iwai 提交于
On codec chips with both audio and modem functions (e.g. Conexant one), performing AC97_RESET resets the whole registers. When both audio and modem drivers are resumed at the same time, the modem one often is resumed after the audio, and it results in the reset of audio registers (ALSA bug#3333). This patch fixes such a problem. Since the modem codec basically doesn't need AC97_RESET, skip this initialization unless specified as audio. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Takashi Iwai 提交于
Replace the direct calculation of jiffies with msecs_to_jiffies(). Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Takashi Iwai 提交于
Added missing static to snd_ac97_restore_status() and snd_ac97_restore_iec958() functions. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Takashi Iwai 提交于
Clean up codes using the new common snd_ctl_boolean_*_info() callbacks. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
- 16 5月, 2007 1 次提交
-
-
由 Daniel T Chen 提交于
Included is a patch against current alsa-kernel hg tip adding quirks that Ubuntu Dapper/Edgy/Feisty contains. Signed-off-by: NDaniel T Chen <crimsun@ubuntu.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
- 11 5月, 2007 3 次提交
-
-
由 John Utz 提交于
This patch provides a single 8 way enum called 'Smart 5.1 Select' with some reasonable names for each enum that allows the user to choose which of the 8 possible settings for vt1617a's version of what via calls 'Smart 5.1'. Signed-off-by: NJohn Utz <john.utz@dmx.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Takashi Iwai 提交于
Fix internal speaker output of MSI L720 laptop with ALC655 codec. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Takashi Iwai 提交于
Include ac97_patch.c from the main ac97_codec.c in order to make bunch of patch_*() functions static. This helps optimization. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
- 09 5月, 2007 1 次提交
-
-
由 Michael Opdenacker 提交于
Signed-off-by: NMichael Opdenacker <michael@free-electrons.com> Signed-off-by: NAdrian Bunk <bunk@stusta.de>
-
- 14 3月, 2007 1 次提交
-
-
由 Randy Cushman 提交于
This patch fixes the control logic for shared Microphone in/Center+LFE out and Line in/Surround out jacks for Analog Devices AD1888, AD1980 and AD1985 AC '97 CODECs. Signed-off-by: NRandy Cushman <rcushman_linux@earthlink.net> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
- 06 3月, 2007 1 次提交
-
-
由 Takashi Iwai 提交于
Added Thinkpad X31 and R40 to AD1981x line/HP-jack-sense blacklist for avoiding the harmful mixer controls. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
- 14 2月, 2007 1 次提交
-
-
由 Takashi Iwai 提交于
Fixed the silent output problem on laptops with Conexant Cx20551 codec chip, such as Packard-bell EasyNote A* series. The information was taken from ALSA bug#1134. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
- 09 2月, 2007 9 次提交
-
-
由 Takashi Iwai 提交于
Remove delayed work properly at free and suspend in ac97 codec and ak4114 drivers. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Takashi Iwai 提交于
Mark TLV data as 'const' Signed-of-by: NPhilipp Matthias Hahn <pmhahn@pmhahn.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Daniel Jacobowitz 提交于
This patch connects the extra vt1616 controls for the vt1617a, which is necessary to control the rear speakers on e.g. a Shuttle SN25P. Signed-off-by: NDaniel Jacobowitz <drow@false.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Randy Cushman 提交于
Previously, ac97_codec.c was coded to support AD1986 and AD1986A CODECs using code written for the AD1985 CODEC. This allowed the LINE_OUT and HEADPHONE jacks to function properly, however register differences between the CODECs prevented line and microphone inputs from functioning. Specifically, this patch fixes issues with the following mixer controls: 'V_REFOUT', 'Spread Front to Surround and Center/LFE', 'Exchange Front/Surround', 'Surround Jack Mode', and 'Channel Mode'. This patch removes the undocumented AD1888 control 'High Pass Filter Enable' and adds the new control 'Exchange Mic/Line In'. Signed-off-by: NRandy Cushman <rcushman_linux@earthlink.net> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Randy Cushman 提交于
This patch replaces the 'V_REFOUT Enable' mixer switch control with a listbox control for the AD1985 CODEC. Previous patch 'AD1888 mixer controls for DC mode' added controls that were propogated to multiple codecs. For the AD1985 codec, the bits VREFH and VREFD function differently, preventing the 'V_REFOUT Enable' control from setting V_REFOUT to Hi-Z. This patch also corrects an issue in which register bits relating to mixer controls 'Surround Jack Mode' and 'Channel Mode'. The register bits controlled by these controls were being set at boot time to states inconsistent with the stored values of these controls. Signed-off-by: NRandy Cushman <rcushman_linux@earthlink.net> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Randy Cushman 提交于
This patch fixes the Microphone and LINE_IN select logic for Analog Devices surround codecs with shared jacks. The existing code can never utilize the shared jacks for Microphone and LINE_IN due to the reversed jack selection logic. The patched code correctly selects the shared jack for input if the 'Channel Mode' selector does not specify that the jack is to be used for output. Specifically, in '2ch' mode the Center/LFE jack is used for microphone input and the Surround jack is used for LINE_IN, in '4ch' mode the Center/LFE jack is used for microphone input and the Surround jack is used for output, and in '6ch' mode both jacks are used for output. Signed-off-by: NRandy Cushman <rcushman_linux@earthlink.net> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 James C Georgas 提交于
The STAC9708/11 AC97 codecs implement the PCM Out Path & Mute bit in the General Purpose register (0x20:F), even though they don't implement the actual function in the mixer. Since the alsa tests for the function by toggling the bit and reading it back to see if it changed, it mistakenly creates a useless control. This patch explicitly removes the control when the codec is an STAC9708/11. I put the check in patch_sigmatel_stac9708_specific(), because I have an SBLive with this chip on it. I don't know if the STAC9758 or other codecs also behave this way. If they do, then this check could maybe go in patch_sigmatel_stac97xx_specific(), or some other more general function. Signed-off-by: NJames C Georgas <jgeorgas@rogers.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Takashi Iwai 提交于
Don't enable power-saving mode on drivers that don't support it. The supporting drivers set AC97_SCAP_POWER_SAVE to scaps at creation of ac97 instance. Currently enable on the following drivers: intel8x0, intel8x0m, atiixp, atiixp-modem, via82xx and via82xx-modem. Also, a bit clean up of power-saving stuff: - Don't create an own workq - Remove superfluous ifdefs Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Jerome Demange 提交于
Signed-off-by: NJerome Demange <jdemange@cict.fr> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
- 20 12月, 2006 4 次提交
-
-
由 James Courtier-Dutton 提交于
Signed-off-by: NJames Courtier-Dutton <James@superbug.co.uk> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 James C Georgas 提交于
This patch fixes a couple of bit update functions in alsa-kernel/pci/ac97/ac97_codec.c, which could possibly corrupt bits not in the given mask. Specifically, it'll clobber unset bits in the target that are not in the mask, when the corresponding bit in the given new value is set. Signed-off-by: NJames C Georgas <jgeorgas@rogers.com> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Takashi Iwai 提交于
Fix the case cidx2 >= 0 and cidx2 < 0 which may result in negative array index. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Jaroslav Kysela 提交于
New PCI ID described and tested Spectr <spectr@gmail.com> . Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
- 13 12月, 2006 1 次提交
-
-
由 Nicolas Pitre 提交于
Commit 2d4ba4a3 introduced a dependency that was never meant to exist when the ac97_bus.c module was created. Move ac97_bus.c up the directory hierarchy to make sure it is built when selected even if sound is configured out so things work as originally intended. Signed-off-by: NNicolas Pitre <nico@cam.org> Acked-by: NRandy Dunlap <randy.dunlap@oracle.com> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 22 11月, 2006 1 次提交
-
-
由 David Howells 提交于
Fix up for make allyesconfig. Signed-Off-By: NDavid Howells <dhowells@redhat.com>
-
- 22 10月, 2006 1 次提交
-
-
由 Takashi Iwai 提交于
Fix the bug in AC97 power-saving mode that the power isn't turned on when power_save is set to 1 via sysfs during the power off state. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
- 07 10月, 2006 1 次提交
-
-
由 Luke Zhang 提交于
This patch by Luke Zhang fixes a couple of issues with the WM9712 support in ac97_patch.c Changes:- o Fix Out3 ZC switch invert. o Extend capture volume control to 6 bits. o Change Mic 1 volume mask to 5 bits (31). o Add Mic 2 volume. Signed-off-by: NLuke Zhang <lzhang@intrinsyc.com> Signed-off-by: NLiam Girdwood <liam.girdwood@wolfsonmicro.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
- 23 9月, 2006 8 次提交
-
-
由 Liam Girdwood 提交于
This patch fixes a build error (introduced by me) in ac97_patch.c wrt WM9705 touchscreen. o Removed spurious '3D' from character after |= operation (0x3D is ASCII for '=') Signed-off-by: NLiam Girdwood <liam.girdwood@wolfsonmicro.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Ville Syrjala 提交于
AD1819 volume registers can hold extra bits which do not affect the actual volume. Add a res_table to the codec patch to fix the problem. PCM, line and mic volume were tested. Signed-off-by: NVille Syrjala <syrjala@sci.fi> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Andrey Liakhovets 提交于
Fix the bad sound quality on VIA EPIA system using VIA VT1617A (ALSA bug#2381). Signed-off-by: NAndrey Liakhovets <liakh@dol.ru> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Magnus Sandin 提交于
The attached patch will force building the S/PDIF controls on the PCU SSID for Asus P5P800-VM motherboard, even if the AC97_EI_SPDIF bit is not set. Signed-off-by: NMagnus Sandin <magnus@sandin.cx> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Takashi Iwai 提交于
Added the dB scale information to ak4531 codec driver. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Takashi Iwai 提交于
Added the TLV support to AC97 codec driver for addition of dB range information. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Magnus Sandin 提交于
Attached is the patch for the LG K1 Express (K1-2333V) laptop that enables sound output. Signed-off-by: NMagnus Sandin <magnus@sandin.cx> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-
由 Mike Rapoport 提交于
This patch adds some codec-specific controls for Philips UCB1400 codec. Signed-off-by: NMike Rapoport <mike@compulab.co.il> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NJaroslav Kysela <perex@suse.cz>
-