The hci_bcm platform-device hack which was used to implement
power management for ACPI devices is being replaced by a
serial-device-bus implementation.

Unfortunately, when the corresponding change to the ACPI code lands (a
change that will stop enumerating and registering the serial-device-node
child as a platform device) PM will break silently unless serdev
TTY-port controller support has been enabled. Specifically, hciattach
(btattach) would still succeed, but power management would no longer
work.

Although this is strictly a runtime dependency, let's make the driver
depend on SERIAL_DEV_CTRL_TTYPORT, which is the particular serdev
controller implementation used by the ACPI devices currently managed by
this driver, to avoid breaking PM without anyone noticing.

Note that the driver already has a (build-time) dependency on the serdev
bus code.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

As the overwriting of IRQ polarity to active low occurs during the driver
probe using 'bt_dev_warn' to display the warning results in '(null)' being
displayed for the device. This patch uses 'dev_warn' to correctly display
the device in the warning instead.
Signed-off-by: NIan W MORRISON <ianwmorrison@gmail.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

  CC      net/bluetooth/selftest.o
net/bluetooth/selftest.c: In function ‘bt_selftest_init’:
net/bluetooth/selftest.c:246:3: warning: ‘duration’ may be used uninitialized in this function [-Wmaybe-uninitialized]
   snprintf(test_ecdh_buffer, sizeof(test_ecdh_buffer),
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     "PASS (%llu usecs)\n", duration);
     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/bluetooth/selftest.c:203:21: note: ‘duration’ was declared here
  unsigned long long duration;
                     ^~~~~~~~
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. As already done in hci_qca, add
struct hci_uart pointer to priv structure.
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Make the serdev driver use struct bcm_device as its driver data and share
all the pm / GPIO / IRQ related code paths with the platform driver.

After this commit the 2 drivers are in essence the same and the serdev
driver interface can be used for all ACPI enumerated HCI UARTs.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Use dev_get_drvdata instead of platform_get_drvdata in the suspend /
resume functions. This is a preparation patch for adding (runtime)pm
support to the serdev path.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The ACPI subsys is going to move over to instantiating ACPI enumerated
HCIs as serdevs, rather then as platform devices.

So we need to make bcm_acpi_probe() suitable for use on non platform-
devices too, which means that we cannot rely on platform_get_irq()
getting called.

This commit modifies bcm_acpi_probe() to directly get the irq from
the ACPI resources, this is a preparation patch for adding (runtime)pm
support to the serdev path.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

After our previous changes, there is nothing platform specific about
bcm_platform_probe anymore, rename it to bcm_get_resources.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The ACPI subsys is going to move over to instantiating ACPI enumerated
HCIs as serdevs, rather then as platform devices.

This means that the serdev driver paths of hci_bcm.c also need to start
supporting (runtime)pm through GPIOs and a host-wake IRQ.

The hci_bcm code is already mostly independent of how the HCI gets
instantiated, but even though the code only cares about pdev->dev, it
was storing pdev itself in struct bcm_device.

This commit stores pdev->dev rather then pdev in struct bcm_device, this
is a preparation patch for adding (runtime)pm support to the serdev path.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The ACPI subsys is going to move over to instantiating ACPI enumerated
HCIs as serdevs, rather then as platform devices.

Most of the code in bcm_platform_probe is actually not platform
specific and will work with any struct device passed to it, the one
platform specific call in bcm_platform_probe is platform_get_irq.

This commit moves platform_get_irq call to the platform-driver's bcm_probe
function, this is a preparation patch for adding (runtime)pm support to
the serdev path.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since bcm_acpi_probe calls bcm_platform_probe, bcm_probe always ends up
calling bcm_platform_probe.

This commit simplifies things by making bcm_probe always call
bcm_platform_probe itself.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This commit fixes 2 issues with host-wake irq trigger type handling
in hci_bcm:

1) bcm_setup_sleep sets sleep_params.host_wake_active based on
bcm_device.irq_polarity, but bcm_request_irq was always requesting
IRQF_TRIGGER_RISING as trigger type independent of irq_polarity.

This was a problem when the irq is described as a GpioInt rather then
an Interrupt in the DSDT as for GpioInt-s the value passed to request_irq
is honored. This commit fixes this by requesting the correct trigger
type depending on bcm_device.irq_polarity.

2) bcm_device.irq_polarity was used to directly store an ACPI polarity
value (ACPI_ACTIVE_*). This is undesirable because hci_bcm is also
used with device-tree and checking for something like ACPI_ACTIVE_LOW
in a non ACPI specific function like bcm_request_irq feels wrong.

This commit fixes this by renaming irq_polarity to irq_active_low
and changing its type to a bool.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Fix a NULL pointer deref (hu->tty) when calling hci_uart_set_flow_control
on hci_uart-s using serdev.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

That Bluetooth SMP knows about the private key is pointless, since the
detection of debug key usage is actually via the public key portion.
With this patch, the Bluetooth SMP will stop keeping a copy of the
ecdh private key and will let the crypto subsystem to generate and
handle the ecdh private key, potentially benefiting of hardware
ecc private key generation and retention.

The loop that tries to generate a correct private key is now removed and
we trust the crypto subsystem to generate a correct private key. This
backup logic should be done in crypto, if really needed.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

tmp buffer contains the swapped private key. In case the setkey call
failed, the tmp buffer was freed without clearing the private key.

Zeroize the temporary buffer so we don't leak the private key.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

ecdh_helper functions were hiding the error codes and chose to return
the return value of an relational operator, "==". Remove the unnecessary
query and reveal the error codes.

While updating the return values, code in a way that compilers will
warn in case of uninitialized err.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Before this change, a new crypto tfm was allocated, each time,
for both key generation and shared secret computation.

Allocate a single tfm for both cases.
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

pr_err(), dev_err() and pr_info() messages should terminated with
a new-line to avoid other messages being concatenated onto the end.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

All older compiler versions up to gcc-4.9 produce these
harmless warnings:

drivers/net/ieee802154/ca8210.c: In function 'ca8210_skb_tx':
drivers/net/ieee802154/ca8210.c:1947:9: warning: missing braces around initializer [-Wmissing-braces]

This changes the syntax to something that works on all versions
without warnings.

Fixes: ded845a7 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NStefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Retrieve BD address from the local-bd-address property.
This address must be unique and is usually added in the DT
by the bootloader which has access to the provisioned data.
Signed-off-by: NLoic Poulain <loic.poulain@linaro.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add optional local-bd-address property which is a 6-byte array
storing the assigned BD address. Since having a unique BD address
is critical, a per-device property value should be allocated.
This property is usually added by the boot loader which has access
to the provisioned data.
Signed-off-by: NLoic Poulain <loic.poulain@linaro.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

In the same way as Ethernet, gather the Bluetooth related bindings in
one file. Introduce the bluetooth-bd-address property which can be used
to store the assigned BD address.
Signed-off-by: NLoic Poulain <loic.poulain@linaro.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch implements the hdev setup function since wcnss-bt does not have
persistent memory to store an allocated BD address. The device is therefore
marked as unconfigured if no BD address has been previously retrieved.
Signed-off-by: NLoic Poulain <loic.poulain@linaro.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

Simon Wunderlich says:

====================
This cleanup patchset includes the following patches:

 - bump version strings, by Simon Wunderlich

 - Cleanup patches to make checkpatch happy, by Sven Eckelmann (3 patches)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use pci_ari_enabled() from the PCI core instead of the identical local copy
bnx2x_ari_enabled().  No functional change intended.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jesper Dangaard Brouer says:

====================
Improve xdp_monitor samples/bpf

Here are some improvements to the xdp_monitor tool currently located
under samples/bpf/.  Once the tools library libbpf become more feature
complete, xdp_monitor should be converted to use it, and be moved into
tools/bpf/xdp/ or tools/xdp/.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Other concurrent running programs, like perf or the XDP program what
needed to be monitored, might take up part of the max locked memory
limit.  Thus, the xdp_monitor tool have to set the RLIMIT_MEMLOCK to
RLIM_INFINITY, as it cannot determine a more sane limit.

Using the man exit(3) specified EXIT_FAILURE return exit code, and
correct other users too.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also monitor the tracepoint xdp_exception.  This tracepoint is usually
invoked by the drivers.  Programs themselves can activate this by
returning XDP_ABORTED, which will drop the packet but also trigger the
tracepoint.  This is useful for distinguishing intentional (XDP_DROP)
vs. ebpf-program error cases that cased a drop (XDP_ABORTED).

Drivers also use this tracepoint for reporting on XDP actions that are
unknown to the specific driver.  This can help the user to detect if a
driver e.g. doesn't implement XDP_REDIRECT yet.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first 8 bytes of the tracepoint context struct are not accessible
by the bpf code.  This is a choice that dates back to the original
inclusion of this code.

See explaination in:
 commit 98b5c2c6 ("perf, bpf: allow bpf programs attach to tracepoints")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simon Horman says:

====================
nfp: extend match and action for flower offload

Pieter says:

This series extends flower offload match and action capabilities. It
specifically adds offload capabilities for matching on MPLS, TTL, TOS
and flow label. Furthermore offload capabilities for action have been
expanded to include set ethernet, ipv4, ipv6, tcp and udp headers.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we did not have offloading support for set TCP/UDP actions. This
patch enables TC flower offload of set TCP/UDP sport and dport actions.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we did not have offloading support for set IPv6 actions. This
patch enables TC flower offload of set IPv6 src and dst address actions.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we did not have offloading support for set IPv4 actions. This
patch enables TC flower offload of set IPv4 src and dst address actions.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we did not have offloading support for set ethernet actions.
This patch enables TC flower offload of set ethernet actions.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously matching on IPv6 ttl and tos fields were not offloaded. This
patch enables offloading IPv6 ttl and tos as match fields.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously matching on IPv4 ttl and tos fields were not offloaded. This
patch enables offloading IPv4 ttl and tos as match fields.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously MPLS match offloading was not supported. This patch enables
MPLS match offloading support for label, bos and tc fields.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit cc71b7b0 ("net/ipv6: remove unused err variable on
icmpv6_push_pending_frames") exposed icmpv6_push_pending_frames
return value not being used.

Remove now unnecessary int err declarations and uses.

Miscellanea:

o Remove unnecessary goto and out: labels
o Realign arguments
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

int err is unused by icmpv6_push_pending_frames(), this patch returns removes the variable and returns the function with 0.

git bisect shows this variable has been around since linux has been in git in commit 1da177e4.

This was found by running make coccicheck M=net/ipv6/ on linus' tree on commit 77ede3a0 (current HEAD as of this patch).
Signed-off-by: NTim Hansen <devtimhansen@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>