Merge tag 'fixes-for-v4.5-rc6' of http://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v4.5-rc6

The most important fixes here are:

a) yet another fix to dwc3's EP transfer resource
assignment logic. This time around we will be
pre-allocating transfer resources to avoid any
future issues;

b) two DMA fixes for the old MUSB driver.

c) dwc2's data toggle fix for FS

Other than these, we have a few other minor fixes
elsewhere.

Now that I have switched to another company, I won't
be able to help by maintaining OMAP USB Support and/or
the MUSB driver.

OMAP USB Support is left Orphaned. MUSB's new
maintainer will be Bin Liu from Texas Instruments
who has accepted to take over starting with v4.6.

Cc: Bin Liu <b-liu@ti.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

Commit ac33cdb1 ("usb: musb: Remove ifdefs for musb_host_rx in
musb_host.c part5") introduces a problem setting DMA host mode.

The musb_advance_schedule() is called immediately after receiving an
endpoint RX interrupt without waiting for the DMA transfer to complete.

As a consequence when the dma complete interrupt arrives the in_qh
member of hw_ep is already null an the musb_host_rx() exits on !urb
error case. Fix the done condition that advances the musb schedule.
Signed-off-by: NCristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: NJoshua Henderson <joshua.henderson@microchip.com>
Tested-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

When working in Dual Role Device mode, USB state machine is not kicked,
when host or gadget drivers are loaded. Fix this be explicitly triggering
state detection on client driver load.

Issue is that if the board is booted without micro usb cable and usb
device attached, kernel fails to populate the usb host and device.
The reason for this is that the state machine worker logic only checks
for USB_DR_MODE_PERIPHERAL and USB_DR_MODE_HOST modes to run worker
thread. However if the phy is configured in OTG mode it would fail
to run the state machine, resulting in failure to detect for very
first time.

This patch fixes the issue by removing the explicit checks.

Issue is noticed on Qualcomm Dragon board DB410C.

[srinivas.kandagatla@linaro.org: Added more details to log]
Signed-off-by: NIvan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

This patch fixes the register offset used for super-speed connection's
max packet size. Without it using the 338x series of devices in enhanced
mode will only allow full or high speed operation to function correctly.
Signed-off-by: NSimon Appleby <simon.appleby@pickeringtest.com>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

Gadgetfs driver called usb_gadget_unregister_driver unconditionally, even
if it didn't register it earlier due to other failures. This patch fixes
this.
Reported-by: NVegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Tested-by: NVegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

Retry gadget probe only if the probe result is -EPROBE_DEFER, not on
every probe error.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

This reverts commit d8f00cd6.

Tony writes:

This upstream commit is causing an oops:
d8f00cd6 ("usb: hub: do not clear BOS field during reset device")

This patch has already been included in several -stable kernels.  Here
are the affected kernels:
4.5.0-rc4 (current git)
4.4.2
4.3.6 (currently in review)
4.1.18
3.18.27
3.14.61

How to reproduce the problem:
Boot kernel with slub debugging enabled (otherwise memory corruption
will cause random oopses later instead of immediately)
Plug in USB 3.0 disk to xhci USB 3.0 port
dd if=/dev/sdc of=/dev/null bs=65536
(where /dev/sdc is the USB 3.0 disk)
Unplug USB cable while dd is still going
Oops is immediate:
Reported-by: NTony Battersby <tonyb@cybernetics.com>
Cc: Du, Changbin <changbin.du@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-serial-4.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for v4.5-rc5

Here are some new device ids.
Signed-off-by: NJohan Hovold <johan@kernel.org>

Merge tag 'usb-ci-v4.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus

Peter writes:

Some tiny bug fixes for chipidea driver

In case of error, the function usb_phy_generic_register()
returns ERR_PTR() and never returns NULL. The NULL test in
the return value check should be replaced with IS_ERR().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NPeter Chen <peter.chen@nxp.com>

The write value is 8bit, but currently writing a larger number
(eg a doubled digit) is not errored but instead gets cast and
sets off an action probably undesired.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
(Change the style of commit log to fix checkpatch.pl warning)

Thomas reports:

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=05c6 ProdID=6001 Rev=00.00
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=1234567890ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Cc: <stable@vger.kernel.org>
Reported-by: NThomas Schäfer <tschaefer@t-online.de>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add USB ID for cp2104/5 devices on GE B650v3 and B850v3 boards.
Signed-off-by: NKen Lin <ken.lin@advantech.com.tw>
Signed-off-by: NAkshay Bhat <akshay.bhat@timesys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

$ lsusb:
Bus 001 Device 101: ID 1e0e:9001 Qualcomm / Option

$ usb-devices:
T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=101 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  2
P:  Vendor=1e0e ProdID=9001 Rev= 2.32
S:  Manufacturer=SimTech, Incorporated
S:  Product=SimTech, Incorporated
S:  SerialNumber=0123456789ABCDEF
C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)

The last interface (6) is used for Android Composite ADB interface.

Serial port layout:
0: QCDM/DIAG
1: NMEA
2: AT
3: AT/PPP
4: audio
Signed-off-by: NAndrey Skvortsov <andrej.skvortzov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Commit 754fe4a9 ("usb: musb: Remove ifdefs for TX DMA for musb_host.c")
introduces a problem setting the desired channel mode for the Mentor DMA
engine.

There is a case where an address is incorrectly assigned to the DMA
channel desired mode when it should instead be assigned the actual mode
value. This results in the value of channel->desired_mode not being
correct.
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NCristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: NJoshua Henderson <joshua.henderson@microchip.com>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

IS_ERR_VALUE macro should be used only with unsigned long type.
Otherwise it can work incorrectly.

The patch follows conclusion from discussion on LKML [1][2].

[1]: http://permalink.gmane.org/gmane.linux.kernel/2120927
[2]: http://permalink.gmane.org/gmane.linux.kernel/2150581Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

If NO_DMA=y:

    ERROR: "usb_gadget_map_request" [drivers/usb/dwc2/dwc2.ko] undefined!
    ERROR: "usb_gadget_unmap_request" [drivers/usb/dwc2/dwc2.ko] undefined!
    ERROR: "bad_dma_ops" [drivers/usb/dwc2/dwc2.ko] undefined!

Add a dependency on HAS_DMA to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

There will be data toggle error happen for full speed buld-out transfer.
The data toggle bit is saved in qh for non-control transfers, it is wrong
to  check the qtd for that case.

Also fix one static analysis tool issue after fix the data toggle error.

John Youn:
* Added WARN() to warn on improper usage of the
  dwc2_hcd_save_data_toggle() function.
Signed-off-by: NDyson Lee <dyson.lee@intel.com>
Signed-off-by: NTang, Jianqiang <jianqiang.tang@intel.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

Fixes memory manipulation issues and makes Host DDMA bulk transfers
work.

dwc2_process_non_isoc_desc() must return non zero value ONLY when
failure happens in one of the queued descriptors. After receiving
non zero value the caller must stop processing of remaining
QTDs and their descriptors from chain.

Commit 26a19ea6 ("usb: dwc2: host: fix use of qtd after
free in desc dma mode") breaks non_isoc transaction completion logic
in Host DDMA mode. There were bugs before that, but after this patch
dwc2_process_non_isoc_desc() returns fail status even if descriptor
was processed normally. This causes break from loop which is processing
remaining descriptors assigned to QTD, which is not correct for QTDs
containing more than one descriptor.

Current dwc2 driver gathers queued BULK URBs until receiving URB
without URB_NO_INTERRUPT flag. Once getting it, SW creates
descriptor chain, stores it in qh structure and passes start
address to HW. Multiple URB data is contained in that chain.
Hence on getting error on descriptor after its processing by HW,
SW should go out of both loops(qh->qtd, qtd->descs) and report
the failure.

Fixes: 26a19ea6 ("usb: dwc2: host: fix use of qtd after free in desc dma mode")
Cc: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NVardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda618 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.

The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:

1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.

2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).

The following simplified method is used instead:

All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.

This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.

Fixes: aebda618 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: NRavi Babu <ravibabu@ti.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

Fixes an issue found on rockchip rk3036 and rk3188 SOC platforms. For
some reason, the existing msleep(25) is not enough after the force mode.
The following patch was reported to fix the issue.

This does increase the probe delay again slightly, but not up to the
level it was before the original series of patches that this fixes. It
does not cause any other issues when tested on Synopsys HAPS and Altera
socfpga platforms.

Need to revisit this series next release to see if we can address these
issues without having an unconditional delay.

Fixes: 09c96980 ("usb: dwc2: Add functions to set and clear force mode")
Reported-by: NCaesar Wang <caesar.upstream@gmail.com>
Reported-by: NMichael Niewoehner <linux@mniewoehner.de>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NCaesar Wang <caesar.upstream@gmail.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

Pull char/misc driver fixes from Greg KH:
 "Here are 3 fixes for some reported issues.  Two nvmem driver fixes,
  and one mei fix.  All have been in linux-next just fine"

* tag 'char-misc-4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  nvmem: qfprom: Specify LE device endianness
  nvmem: core: return error for non word aligned access
  mei: validate request value in client notify request ioctl

Pull driver core fix from Greg KH:
 "Here is one driver core, well klist, fix for 4.5-rc4.

  It fixes a problem found in the scsi device list traversal that
  probably also could be triggered by other subsystems.

  The fix has been in linux-next for a while with no reported problems"

* tag 'driver-core-4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  klist: fix starting point removed bug in klist iterators

Pull tty/serial fixes from Greg KH:
 "Here are a number of small tty and serial driver fixes for 4.5-rc4
  that resolve some reported issues.

  One of them got reverted as it wasn't correct based on testing, and
  all have been in linux-next for a while"

* tag 'tty-4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  Revert "8250: uniphier: allow modular build with 8250 console"
  pty: make sure super_block is still valid in final /dev/tty close
  pty: fix possible use after free of tty->driver_data
  tty: Add support for PCIe WCH382 2S multi-IO card
  serial/omap: mark wait_for_xmitr as __maybe_unused
  serial: omap: Prevent DoS using unprivileged ioctl(TIOCSRS485)
  8250: uniphier: allow modular build with 8250 console
  tty: Drop krefs for interrupted tty lock

Pull PHY fixes from Greg KH:
 "Here are a couple of PHY driver fixes for 4.5-rc4.

  A few small phy issues.  All have been in linux-next with no reported
  issues"

* tag 'usb-4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  phy: twl4030-usb: Fix unbalanced pm_runtime_enable on module reload
  phy: twl4030-usb: Relase usb phy on unload
  phy: core: fix wrong err handle for phy_power_on
  phy: Restrict phy-hi6220-usb to HiSilicon arm64

Pull perf tooling fixes from Thomas Gleixner:
 "Another round of fixes for the perf tooling side:

   - Prevent a NULL pointer dereference in tracepoint error handling

   - Fix a thread handling bug in the intel_pt error handling code

   - Search both .eh_frame and .debug_frame sections as toolchains seem
     to have random choices of storing the CFI information

   - Fix the perf state interval output values, which got broken when
     fixing the overall output"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf stat: Fix interval output values
  perf probe: Search both .eh_frame and .debug_frame sections for probe location
  perf tools: Fix thread lifetime related segfaut in intel_pt
  perf tools: tracepoint_error() can receive e=NULL, robustify it

Pull lockdep fix from Thomas Gleixner:
 "A single fix for the stack trace caching logic in lockdep, where the
  duplicate avoidance managed to store no back trace at all"

* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/lockdep: Fix stack trace caching logic

Pull timer fix from Thomas Gleixner:
 "A single fix preventing a 32bit overflow in timespec/val to cputime
  conversions on 32bit machines"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  cputime: Prevent 32bit overflow in time[val|spec]_to_cputime()

Pull irqchip fixes from Thomas Gleixner:
 "Another set of ARM SoC related irqchip fixes:
   - Plug a memory leak in gicv3-its
   - Limit features to the root gic interrupt controller
   - Add a missing barrier in the gic-v3 IAR access
   - Another compile test fix for sun4i"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3: Make sure read from ICC_IAR1_EL1 is visible on redestributor
  irqchip/gic: Only set the EOImodeNS bit for the root controller
  irqchip/gic: Only populate set_affinity for the root controller
  irqchip/gicv3-its: Fix memory leak in its_free_tables()
  irqchip/sun4i: Fix compilation outside of arch/arm

Pull x86 fixes from Thomas Gleixner:
 "Two small fixlets for x86:

   - Prevent a KASAN false positive in thread_saved_pc()

   - Fix a 32-bit truncation problem in the x86 numa code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm/numa: Fix 32-bit memblock range truncation bug on 32-bit NUMA kernels
  x86: Fix KASAN false positives in thread_saved_pc()

Pull MIPS fixes from Ralf Baechle:
 "Here's the first round of MIPS fixes after the merge window:

   - Detect Octeon III's PCI correctly.
   - Fix return value of the MT7620 probing function.
   - Wire up the copy_file_range syscall.
   - Fix 64k page support on 32 bit kernels.
   - Fix the early Coherency Manager probe.
   - Allow only hardware-supported page sizes to be selected for R6000.
   - Fix corner cases for the RDHWR nstruction emulation on old hardware.
   - Fix FPU handling corner cases.
   - Remove stale entry for BCM33xx from the MAINTAINERS file.
   - 32 and 64 bit ELF headers are different, handle them correctly"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  mips: Differentiate between 32 and 64 bit ELF header
  MIPS: Octeon: Update OCTEON_FEATURE_PCIE for Octeon III
  MIPS: pci-mt7620: Fix return value check in mt7620_pci_probe()
  MIPS: Fix early CM probing
  MIPS: Wire up copy_file_range syscall.
  MIPS: Fix 64k page support for 32 bit kernels.
  MIPS: R6000: Don't allow 64k pages for R6000.
  MIPS: traps.c: Correct microMIPS RDHWR emulation
  MIPS: traps.c: Don't emulate RDHWR in the CpU #0 exception handler
  MAINTAINERS: Remove stale entry for BCM33xx chips
  MIPS: Fix FPU disable with preemption
  MIPS: Properly disable FPU in start_thread()
  MIPS: Fix buffer overflow in syscall_get_arguments()

Pull ARM fixes from Russell King:
 "A couple of ARM fixes from Linus for the ICST clock generator code"

[ "Linus" here is Linus Walleij.  Name-stealer.

       Linus "there can be only one" Torvalds ]

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8519/1: ICST: try other dividends than 1
  ARM: 8517/1: ICST: avoid arithmetic overflow in icst_hz()

Pull component helper fixes from Russell King:
 "A few fixes for problems people have encountered with the recent
  update to the component helpers"

* 'component' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  component: remove device from master match list on failed add
  component: Detach components when deleting master struct
  component: fix crash on x86_64 with hda audio drivers

Pull more rdma fixes from Doug Ledford:
 "I think we are getting pretty close to done now.  There are four
  one-off fixes in this update:

   - fix ipoib multicast joins
   - fix mlx4 error handling
   - fix mlx5 size computation
   - fix a thinko in core code"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  IB/mlx5: Fix RC transport send queue overhead computation
  IB/ipoib: fix for rare multicast join race condition
  IB/core: Fix reading capability mask of the port info class
  net/mlx4: fix some error handling in mlx4_multi_func_init()

Pull SCSI target fixes from Nicholas Bellinger:
 "This includes the long awaited series to address a set of bugs around
  active I/O remote-port LUN_RESET, as well as properly handling this
  same case with concurrent fabric driver session disconnect ->
  reconnect.

  Note this set of LUN_RESET bug-fixes has been surviving extended
  testing on both v4.5-rc1 and v3.14.y code over the last weeks, and is
  CC'ed for stable as it's something folks using multiple ESX connected
  hosts with slow backends can certainly trigger.

  The highlights also include:

   - Fix WRITE_SAME/DISCARD emulation 4k sector conversion in
     target/iblock (Mike Christie)

   - Fix TMR abort interaction and AIO type TMR response in qla2xxx
     target (Quinn Tran + Swapnil Nagle)

   - Fix >= v3.17 stale descriptor pointer regression in qla2xxx target
     (Quinn Tran)

   - Fix >= v4.5-rc1 return regression with unmap_zeros_data_store new
     configfs store handler (nab)

   - Add CPU affinity flag + convert qla2xxx to use bit (Quinn + HCH +
     Bart)"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  qla2xxx: use TARGET_SCF_USE_CPUID flag to indiate CPU Affinity
  target/transport: add flag to indicate CPU Affinity is observed
  target: Fix incorrect unmap_zeroes_data_store return
  qla2xxx: Use ATIO type to send correct tmr response
  qla2xxx: Fix stale pointer access.
  target/user: Fix cast from pointer to phys_addr_t
  target: Drop legacy se_cmd->task_stop_comp + REQUEST_STOP usage
  target: Fix race with SCF_SEND_DELAYED_TAS handling
  target: Fix remote-port TMR ABORT + se_cmd fabric stop
  target: Fix TAS handling for multi-session se_node_acls
  target: Fix LUN_RESET active TMR descriptor handling
  target: Fix LUN_RESET active I/O handling for ACK_KREF
  qla2xxx: Fix TMR ABORT interaction issue between qla2xxx and TCM
  qla2xxx: Fix warning reported by static checker
  target: Fix WRITE_SAME/DISCARD conversion to linux 512b sectors

Pull thermal management fixes from Eduardo Valentin:
 "Specifics in this pull request:

   - Compilation fixes on SPEAR, and U8500 thermal drivers.
   - RCAR thermal driver now recognizes OF-thermal based thermal zones.
   - Small code rework on OF-thermal.
   - These change have been CI tested using KernelCI bot [1,2].  \o/

  I am taking over on Rui's behalf while he is out.  Happy New Chinese
  Year!

  [1] - https://kernelci.org/build/evalenti/kernel/v4.5-rc3-16-ga53b8394ec3c/
  [2] - https://kernelci.org/boot/all/job/evalenti/kernel/v4.5-rc3-16-ga53b8394ec3c/"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
  thermal: cpu_cooling: fix out of bounds access in time_in_idle
  thermal: allow u8500-thermal driver to be a module
  thermal: allow spear-thermal driver to be a module
  thermal: spear: use __maybe_unused for PM functions
  thermal: rcar: enable to use thermal-zone on DT
  thermal: of: use for_each_available_child_of_node for child iterator

Pull another sound fix from Takashi Iwai:
 "This contains a fix for the double-free of usb-audio MIDI device at
  probe failure"

* tag 'sound-fix-4.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: usb-audio: avoid freeing umidi object twice

Pull ARC fixes from Vineet Gupta:
 "I've been sitting on some of these fixes for a while.

   - Corner case of returning to delay slot from interrupt
   - Changing default interrupt prioiry level
   - Kconfig'ize support for super pages
   - Other minor fixes"

* tag 'arc-4.5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: mm: Introduce explicit super page size support
  ARCv2: intc: Allow interruption by lowest priority interrupt
  ARCv2: Check for LL-SC livelock only if LLSC is enabled
  ARC: shrink cpuinfo by not saving full timer BCR
  ARCv2: clocksource: Rename GRTC -> GFRC ...
  ARCv2: STAR 9000950267: Handle return from intr to Delay Slot #2