Read the Broadcom specific controller features during configuration and
print them for informational purposes.

  < HCI Command: Broadcom Read Controller Features (0x3f|0x006e) plen 0
  > HCI Event: Command Complete (0x0e) plen 12
        Broadcom Read Controller Features (0x3f|0x006e) ncmd 1
          Status: Success (0x00)
          Features: 0x07 0x00 0x00 0x00 0x00 0x00 0x00 0x00
            Multi-AV transport bandwidth reducer
            WBS SBC
            FW LC-PLC
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NSzymon Janc <szymon.janc@codecoup.pl>

The Broadcom BCM20702 Bluetooth controller in ThinkPad-T530 devices
report support for the Set Event Mask Page 2 command, but actually do
return an error when trying to use it.

  < HCI Command: Read Local Supported Commands (0x04|0x0002) plen 0
  > HCI Event: Command Complete (0x0e) plen 68
       Read Local Supported Commands (0x04|0x0002) ncmd 1
         Status: Success (0x00)
         Commands: 162 entries
           ...
           Set Event Mask Page 2 (Octet 22 - Bit 2)
           ...

  < HCI Command: Set Event Mask Page 2 (0x03|0x0063) plen 8
         Mask: 0x0000000000000000
  > HCI Event: Command Complete (0x0e) plen 4
       Set Event Mask Page 2 (0x03|0x0063) ncmd 1
         Status: Unknown HCI Command (0x01)

Since these controllers do not support any feature that would require
the event mask page 2 to be modified, it is safe to not send this
command at all. The default value is all bits set to zero.

T:  Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#=  9 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0a5c ProdID=21e6 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=F82FA8E8CFC0
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Reported-by: NSedat Dilek <sedat.dilek@gmail.com>
Tested-by: NSedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: NSzymon Janc <szymon.janc@codecoup.pl>

This file is filled with complex cryptography. Thus, the comparisons of
MACs and secret keys and curve points and so forth should not add timing
attacks, which could either result in a direct forgery, or, given the
complexity, some other type of attack.
Signed-off-by: NJason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.

Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Switch to use managed variant of acpi_dev_add_driver_gpios() to simplify
error path and fix potentially wrong assingment if ->probe() fails.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

To make the TI WiLink chip work again for Bluetooth, let's add the missing
external clock to the Bluetooth node, such the driver can deal properly
with it during power on/off.

Fixes: ea452678 ("arm64: dts: hikey: Fix WiFi support")
Cc: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add support to manage the external clock provided to the WiLink combo chip
as it's needed for any of the transport interfaces.

To avoid breaking platforms not yet specifying the external clock, we make
it optional. In case the clock is successfully fetched during ->probe(),
let's manage it via the ->open|close() callbacks, to make sure the device
get properly powered on/off.

Fixes: ea452678 ("arm64: dts: hikey: Fix WiFi support")
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The external clock is provided to the TI WiLink combo chip and it's needed
for any of the transport interfaces. However let's make it optional to
avoid breaking existing platforms that yet doesn't specify the clock.

Fixes: ea452678 ("arm64: dts: hikey: Fix WiFi support")
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add compatible values for WiLink chips from 128x and 180x series.
Also the DT binding already contained compatible values for the 127x
series, but the driver did not. This brings the list on par with
the list from wlcore (the wifi driver).
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When inheriting tx_flags from one skbuff to another, always apply a
mask to avoid overwriting unrelated other bits in the field.

The two SKBTX_SHARED_FRAG cases clears all other bits. In practice,
tx_flags are zero at this point now. But this is fragile. Timestamp
flags are set, for instance, if in tcp_gso_segment, after this clear
in skb_segment.

The SKBTX_ANY_TSTAMP mask in __skb_tstamp_tx ensures that new
skbs do not accidentally inherit flags such as SKBTX_SHARED_FRAG.
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NSoheil Hassas Yeganeh <soheil@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bhumika Goyal says:

====================
drivers: net: add const to mii_phy_ops structures

The object references of mii_phy_ops structures are only stored
in the ops field of a mii_phy_def structure. This ops field is of type
const. So, mii_phy_ops structures having similar properties can be
declared as const.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The object references of mii_phy_ops structures are only stored
in the ops field of a mii_phy_def structure. This ops field is of type
const. So, mii_phy_ops structures having similar properties can be
declared as const.
Signed-off-by: NBhumika Goyal <bhumirks@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The object references of mii_phy_ops structures are only stored
in the ops field of a mii_phy_def structure. This ops field is of type
const. So, mii_phy_ops structures having similar properties can be
declared as const.
Signed-off-by: NBhumika Goyal <bhumirks@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2017-06-07

This series contains a fix for e1000e and igb.

Colin Ian King fixes sparse warnings in igb by making functions static.

Chris Wilson provides a fix for a previous commit which is causing an
issue during suspend "e1000e_pm_suspend()", where we need to run
e1000e_pm_thaw() if __e1000_shutdown() is unsuccessful.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use PORT_REG for T4 and T5_PORT_REG for > T4 to write to correct
register to bring down link during shutdown after adapter crash.
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently there's no way to dump the VIF table for an ipmr table other
than the default (via proc). This is a major issue when debugging ipmr
issues and in general it is good to know which interfaces are
configured. This patch adds support for RTM_GETLINK for the ipmr family
so we can dump the VIF table and the ipmr table's current config for
each table. We're protected by rtnl so no need to acquire RCU or
mrt_lock.
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Remove compatibility with old firmware

Up until recently we couldn't enforce a minimal firmware version, which
forced us to be compatible with old firmware versions. This patchset
removes this code and simplifies the driver.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previous patch made it unnecessary to map ports to modules before we
allocate their struct. We can now therefore pass the port struct to
these functions, thereby making them consistent with other functions
that operate on ports.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit be94535f ("mlxsw: spectrum: Make split flow match firmware
requirements") we had to modify the port split flow to overcome quirks
in the device's firmware. This resulted in asymmetrical code with
regards to port creation and removal.

The problem in the firmware is long gone and since we can now enforce a
minimal firmware version, we can simplify the code and make it symmetric
again.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In new firmware versions (that we can now enforce via
request_firmware()), only the first LPM tree is reserved and not the
first two as in older versions.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

===================
net: Remove support from bridge bypass for mlxsw/rocker drivers

Currently setting bridge port attributes and adding FDBs are done via
setting the SELF flag which implies unconsistent offloading model. This
patch-set fixes this behavior by making the bridge and drivers which are
using it to be totally in sync.

This implies several changes:
- Offloading bridge flags from the bridge code.
- Sending notification about FDB add/del to the software bridge in a
  similiar way it is done for the hardware externally learned FDBs.

By making the offloading model more consistent a cleanup is done in
the drivers supporting it. This is done in order to remove un-needed
logic related to dump operation which is redundant.

First add missing functionality to bridge, then clean up the mlxsw/rocker
drivers.

v1->v2
- Move bridge-switchdev related stuff to br_switchdev.c as suggested by Nik
===================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FDB add/delete are now done through the notification chain. The FDBs
are synced with the bridge and there is no need for extra dumping.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bridge port attributes/vlan for mlxsw devices should be set only
from bridge code. The vlans are synced totally with the bridge so
there is no need to special dump support.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for learning FDB through notification. The driver defers
the hardware update via ordered work queue.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the switchdev_trans struct is embedded in the world_ops API.
In order to add support for adding FDB via a notfication chain the API should
be switchdev independent.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for querying supported bridge flags.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the rocker driver supports an option for disabling syncing
the hardware learned FDBs with the software bridge. This behavior
breaks the bridge offload model and thus it is removed.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove support for bridge bypass ndos from stacked devices. At this point
no driver which supports stack device behavior offload supports operation
with SELF flag. The case for upper device is already taken care of in both
of the following cases:

1. FDB add/del - driver should check at the notification cb if the
                 stacked device contains his ports.

2. Port attribute - calls switchdev code directly which checks
                    for case of stack device.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FDB add/del are now done through the notification chain. The FDBs
are synced with the bridge and there is no need for extra dumping.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for learning FDB through notification. The driver defers
the hardware update via ordered work queue. Support for stacked devices
is also provided. In case of a successful FDB add a notification is
sent back to bridge.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current API for sending switchdev notifications implies only FDB
add/del. In order to support notification about successful FDB offload
the API is changed.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bridge port attributes/vlan for mlxsw devices should be set only
from bridge code. The vlans are synced totally with the bridge so
there is no need to special dump support.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for querying supported bridge flags.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the mlxsw driver supports an option for disabling syncing
the hardware learned FDBs with the software bridge. This behavior
breaks the bridge offload model and thus it is removed.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a new static FDB is added to the bridge a notification is sent to
the driver for offload. In case of successful offload the driver should
notify the bridge back, which in turn should mark the FDB as offloaded.

Currently, externally learned is equivalent for being offloaded which is
not correct due to the fact that FDBs which are added from user-space are
also marked as externally learned. In order to specify if an FDB was
successfully offloaded a new flag is introduced.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the bridge doesn't notify the underlying devices about new
FDBs learned. The FDB sync is placed on the switchdev notifier chain
because devices may potentially learn FDB that are not directly related
to their ports, for example:

1. Mixed SW/HW bridge - FDBs that point to the ASICs external devices
                        should be offloaded as CPU traps in order to
			perform forwarding in slow path.
2. EVPN - Externally learned FDBs for the vtep device.

Notification is sent only about static FDB add/del. This is done due
to fact that currently this is the only scenario supported by switch
drivers.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to use the switchdev notifier chain for FDB sync with the
device it has to be changed to atomic. The is done because the bridge
can learn new FDBs in atomic context.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is done as a preparation to moving the switchdev notifier chain
to be atomic. The FDB external learning should be called under rtnl
or rcu.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the flood, learning and learning_sync port attributes are
offloaded by setting the SELF flag. Add support for offloading the
flood and learning attribute through the bridge code. In case of
setting an unsupported flag on a offloded port the operation will
fail.

The learning_sync attribute doesn't have any software representation
and cannot be offloaded through the bridge code.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is done as a preparation stage before setting the bridge port flags
from the bridge code. Currently the device can be queried for the bridge
flags state, but the querier cannot distinguish if the flag is disabled
or if it is not supported at all. Thus, add new attr and a bit-mask which
include information regarding the support on a per-flag basis.

Drivers that support bridge offload but not support bridge flags should
return zeroed bitmask.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>