- 24 11月, 2012 12 次提交
-
-
由 Andrew Lunn 提交于
Control the power to USB and HDD using a fixed regulator. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Tested-by: NMichael Walle <michael@walle.cc> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Andrew Lunn 提交于
Control the power to USB using a fixed regulator. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Tested-by: NJosh Coombs <josh.coombs@gmail.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Andrew Lunn 提交于
Control the power to USB using a fixed regulator. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Andrew Lunn 提交于
Control the power to SATA0 and SATA1 using a fixed regulator. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Tested-by: NJamie Lentin <jm@lentin.co.uk> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Andrew Lunn 提交于
A few boards use a GPIO line to enable power to subsystems, eg USB or SATA devices. Pull in the regulator framework as the first step to controlling these GPIO lines are regulators. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Andrew Lunn 提交于
Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Tested-by: NSimon Baatz <gmbnomis@gmail.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Andrew Lunn 提交于
Also enable the gpio-poweroff driver when DT is used. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Tested-by: NJamie Lentin <jm@lentin.co.uk> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Jamie Lentin 提交于
Given appropriate devicetree bindings, this driver registers a pm_power_off function to set a GPIO line high/low to power down your board. Signed-off-by: NJamie Lentin <jm@lentin.co.uk> Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Tested-by: NSimon Baatz <gmbnomis@gmail.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Jamie Lentin 提交于
The default chip-delay of 25us is a bit too tight for some DNS-320's, and D-Link seem to specify 30us in their kernels for both devices. Increase to 35us to make sure the NAND is stable. Signed-off-by: NJamie Lentin <jm@lentin.co.uk> Acked-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Andrew Lunn 提交于
Now that the EHCI driver has DT support, drop old style configuration of it and add DT in its place. Since all the boards enable the EHCI, enable it by default in kirkwood.dtsi. Any new boards which don't have USB can specifically disable it. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Andrew Lunn 提交于
Based on previous work by Michael Walle and Jason Cooper. Made their work actually work, which required added interrupt from DT and auxdata, along with setting the dma_mask, which DT does not currently do. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Tested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Acked-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Jason Cooper 提交于
merge pinctrl/devel up to: 06763c74 pinctrl: mvebu: move to its own directory
-
- 22 11月, 2012 17 次提交
-
-
由 Nobuhiro Iwamatsu 提交于
Add support for Plat'Home OpenBlocks A6 using the device tree where possible. This commit supports SATA, USB, ether and serial console. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Sebastian Hesselbarth 提交于
It has been a while since dove_defconfig was updated to recent development. This patch adds all currently available Dove boards, including a DT-enabled machine. DT support requires to allow ATAGS passed by boot loader as most of them are not yet capable of passing DT blobs. Also OF_SERIAL is enabled to actually see the bootlog. Finally, sdhci driver for Dove, mv_cesa, GPIO LEDs, and highmem support is added. Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Jason Cooper 提交于
MPLCEC4_DT is relocated because it had been added manually. Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Thomas Petazzoni 提交于
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com> Acked-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Thomas Petazzoni 提交于
This commit converts the 'LaCie Ethernet Disk mini v2' board to the Device Tree. All devices that have existing Device Tree bindings are converted over to the Device Tree, the other devices remain instantiated in the old way, until the respective drivers get the needed Device Tree bindings. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com> Acked-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Thomas Petazzoni 提交于
This commit adds basic DT support for the Orion5x SoC family. It adds an orion5x.dtsi description of the Orion5x SoC as well as the needed DT_MACHINE structure to support boards converted to DT in the future. So far, the Device Tree contains the interrupt controller, the GPIO bank, the UART controllers, the SPI controller, the watchdog, the SATA controller, the I2C controller and the cryptographic engine. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com> Acked-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Thomas Petazzoni 提交于
This commit is a simple mechanical update of the orion5x_defconfig file to the current kernel (i.e, just 'make orion5x_defconfig; make savedefconfig'). Doing this update allows to more easily separate DT-related configuration changes in the following patches. Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Tested by: Maxime Hadjinlian <mhadjinlian@lacie.com> Acked-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Stefan Peter 提交于
Signed-off-by: NStefan Peter <s.peter@mpl.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Tero Jaasko 提交于
Hello, Andrew > > +#define NSA310_GPIO_LED_ESATA_GREEN 12 > > <..> > > +#define NSA310_GPIO_POWER_OFF 48 > > It looks like most of these are not used. Please remove them. True. Fixed. > > +static struct mtd_partition nsa310_mtd_parts[] = { > > + { > > + .name = "uboot", > > + .offset = 0, > > + .size = 0x100000, > > + .mask_flags = MTD_WRITEABLE, > > + }, { > > <..> > You should be able to put all that into DT. Take a look at Correct. I did the conversion and tested that the partitions can be read with dd and produce exactly the same data before and after conversion. So, the partition offsets at least should be fine. > > +static struct i2c_board_info __initdata nsa310_i2c_info[] = { > > + { I2C_BOARD_INFO("adt7476", 0x2e) }, > > +}; > > You can also do this in DT as well. kirkwood-ts219.dtsi has > > i2c@11000 { > status = "okay"; > clock-frequency = <400000>; Ok, I did convert the i2c definition to use the devicetree. The adt7476 device itself is not at reach of device tree, AFAIK and requires more work at there? Thanks for your valuable comments. Following is a new patch that should address the problems and mistakes you pointed and also some of the pointed by Jason Cooper. The nand and i2c are now defined at DT and I also removed the pointless defines and ARM_APPENDED_DTB. It is based against the Linus' official 3.6 version. Best regards, Tero Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Jason Cooper 提交于
This is a new kirkwood box made by Universal Scientific Industrial, Inc. The product description is here: http://www.usish.com/english/products_topkick1281p2.php It is very similar to the dreamplug and other plug devices, with the exception that it has room for a 2.5" SATA HDD internally. Signed-off-by: NJason Cooper <jason@lakedaemon.net> Acked-by: NAndrew Lunn <andrew@lunn.ch> Tested-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
-
由 Michael Walle 提交于
Remove board specific gpio-fan driver registration. Moved into device tree. Signed-off-by: NMichael Walle <michael@walle.cc> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Jason Cooper 提交于
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Simon Guinot 提交于
This patch adds DT board setup for the LaCie NAS Network Space Mini v2 (aka SafeBox). The hardware characteristics are very close to those of the Network Space Lite v2. The main difference are: - A GPIO fan which is only available on the NS2 Mini. - A single USB host port is wired on the NS2 Mini. The NS2 Lite provides an additional dual-mode USB port (host/device). Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Simon Guinot 提交于
This patch adds DT board setup for the LaCie NAS Network Space Lite v2. This board is derived from the Network Space v2 and a lot of hardware characteristics are shared. - CPU: Marvell 88F6192 800Mhz - SDRAM memory: 128MB DDR2 200Mhz - 1 SATA port: internal - Gigabit ethernet: PHY Marvell 88E1318 - Flash memory: SPI NOR 512KB (Macronix MX25L4005A) - i2c EEPROM: 512 bytes (24C04 type) - 2 USB2 ports: host and host/device - 1 push button - 1 SATA LED (bi-color, blue and red) Note that the SATA LED is not compatible with the driver leds-ns2. The LED behaviour ("on", "off" or "SATA activity blink") is controlled via a single MPP (21). Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Simon Guinot 提交于
This patch adds DT board setup for LaCie Network Space v2 and parents, based on the Marvell Kirkwood 6281 SoC. This includes Network Space v2 (Max) and Internet Space v2. Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Simon Guinot 提交于
Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org> Reviewed-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
由 Jason Gunthorpe 提交于
mv64xxx_of_config requires that the tclk frequency be found through the clk stuff rather than through device tree, so add another override for the 2nd controller. Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: NJason Cooper <jason@lakedaemon.net>
-
- 17 11月, 2012 11 次提交
-
-
由 Linus Torvalds 提交于
-
git://git.kernel.org/pub/scm/virt/kvm/kvm由 Linus Torvalds 提交于
Pull KVM fix from Marcelo Tosatti: "A correction for oops on module init with older Intel hosts." * git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: x86: Fix invalid secondary exec controls in vmx_cpuid_update()
-
由 Linus Torvalds 提交于
Merge misc fixes from Andrew Morton. * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (12 patches) revert "mm: fix-up zone present pages" tmpfs: change final i_blocks BUG to WARNING tmpfs: fix shmem_getpage_gfp() VM_BUG_ON mm: highmem: don't treat PKMAP_ADDR(LAST_PKMAP) as a highmem address mm: revert "mm: vmscan: scale number of pages reclaimed by reclaim/compaction based on failures" rapidio: fix kernel-doc warnings swapfile: fix name leak in swapoff memcg: fix hotplugged memory zone oops mips, arc: fix build failure memcg: oom: fix totalpages calculation for memory.swappiness==0 mm: fix build warning for uninitialized value mm: add anon_vma_lock to validate_mm()
-
由 Andrew Morton 提交于
Revert commit 7f1290f2 ("mm: fix-up zone present pages") That patch tried to fix a issue when calculating zone->present_pages, but it caused a regression on 32bit systems with HIGHMEM. With that change, reset_zone_present_pages() resets all zone->present_pages to zero, and fixup_zone_present_pages() is called to recalculate zone->present_pages when the boot allocator frees core memory pages into buddy allocator. Because highmem pages are not freed by bootmem allocator, all highmem zones' present_pages becomes zero. Various options for improving the situation are being discussed but for now, let's return to the 3.6 code. Cc: Jianguo Wu <wujianguo@huawei.com> Cc: Jiang Liu <jiang.liu@huawei.com> Cc: Petr Tesarik <ptesarik@suse.cz> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Minchan Kim <minchan.kim@gmail.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Acked-by: NDavid Rientjes <rientjes@google.com> Tested-by: NChris Clayton <chris2553@googlemail.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
Under a particular load on one machine, I have hit shmem_evict_inode()'s BUG_ON(inode->i_blocks), enough times to narrow it down to a particular race between swapout and eviction. It comes from the "if (freed > 0)" asymmetry in shmem_recalc_inode(), and the lack of coherent locking between mapping's nrpages and shmem's swapped count. There's a window in shmem_writepage(), between lowering nrpages in shmem_delete_from_page_cache() and then raising swapped count, when the freed count appears to be +1 when it should be 0, and then the asymmetry stops it from being corrected with -1 before hitting the BUG. One answer is coherent locking: using tree_lock throughout, without info->lock; reasonable, but the raw_spin_lock in percpu_counter_add() on used_blocks makes that messier than expected. Another answer may be a further effort to eliminate the weird shmem_recalc_inode() altogether, but previous attempts at that failed. So far undecided, but for now change the BUG_ON to WARN_ON: in usual circumstances it remains a useful consistency check. Signed-off-by: NHugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
Fuzzing with trinity hit the "impossible" VM_BUG_ON(error) (which Fedora has converted to WARNING) in shmem_getpage_gfp(): WARNING: at mm/shmem.c:1151 shmem_getpage_gfp+0xa5c/0xa70() Pid: 29795, comm: trinity-child4 Not tainted 3.7.0-rc2+ #49 Call Trace: warn_slowpath_common+0x7f/0xc0 warn_slowpath_null+0x1a/0x20 shmem_getpage_gfp+0xa5c/0xa70 shmem_fault+0x4f/0xa0 __do_fault+0x71/0x5c0 handle_pte_fault+0x97/0xae0 handle_mm_fault+0x289/0x350 __do_page_fault+0x18e/0x530 do_page_fault+0x2b/0x50 page_fault+0x28/0x30 tracesys+0xe1/0xe6 Thanks to Johannes for pointing to truncation: free_swap_and_cache() only does a trylock on the page, so the page lock we've held since before confirming swap is not enough to protect against truncation. What cleanup is needed in this case? Just delete_from_swap_cache(), which takes care of the memcg uncharge. Signed-off-by: NHugh Dickins <hughd@google.com> Reported-by: NDave Jones <davej@redhat.com> Cc: Johannes Weiner <hannes@cmpxchg.com> Cc: <stable@vger.kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Will Deacon 提交于
kmap_to_page returns the corresponding struct page for a virtual address of an arbitrary mapping. This works by checking whether the address falls in the pkmap region and using the pkmap page tables instead of the linear mapping if appropriate. Unfortunately, the bounds checking means that PKMAP_ADDR(LAST_PKMAP) is incorrectly treated as a highmem address and we can end up walking off the end of pkmap_page_table and subsequently passing junk to pte_page. This patch fixes the bound check to stay within the pkmap tables. Signed-off-by: NWill Deacon <will.deacon@arm.com> Cc: Mel Gorman <mgorman@suse.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Mel Gorman 提交于
Jiri Slaby reported the following: (It's an effective revert of "mm: vmscan: scale number of pages reclaimed by reclaim/compaction based on failures".) Given kswapd had hours of runtime in ps/top output yesterday in the morning and after the revert it's now 2 minutes in sum for the last 24h, I would say, it's gone. The intention of the patch in question was to compensate for the loss of lumpy reclaim. Part of the reason lumpy reclaim worked is because it aggressively reclaimed pages and this patch was meant to be a sane compromise. When compaction fails, it gets deferred and both compaction and reclaim/compaction is deferred avoid excessive reclaim. However, since commit c6543459 ("mm: remove __GFP_NO_KSWAPD"), kswapd is woken up each time and continues reclaiming which was not taken into account when the patch was developed. Attempts to address the problem ended up just changing the shape of the problem instead of fixing it. The release window gets closer and while a THP allocation failing is not a major problem, kswapd chewing up a lot of CPU is. This patch reverts commit 83fde0f2 ("mm: vmscan: scale number of pages reclaimed by reclaim/compaction based on failures") and will be revisited in the future. Signed-off-by: NMel Gorman <mgorman@suse.de> Cc: Zdenek Kabelac <zkabelac@redhat.com> Tested-by: NValdis Kletnieks <Valdis.Kletnieks@vt.edu> Cc: Jiri Slaby <jirislaby@gmail.com> Cc: Rik van Riel <riel@redhat.com> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Randy Dunlap 提交于
Fix rapidio kernel-doc warnings: Warning(drivers/rapidio/rio.c:415): No description found for parameter 'local' Warning(drivers/rapidio/rio.c:415): Excess function parameter 'lstart' description in 'rio_map_inb_region' Warning(include/linux/rio.h:290): No description found for parameter 'switches' Warning(include/linux/rio.h:290): No description found for parameter 'destid_table' Signed-off-by: NRandy Dunlap <rdunlap@infradead.org> Cc: Matt Porter <mporter@kernel.crashing.org> Acked-by: NAlexandre Bounine <alexandre.bounine@idt.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Xiaotian Feng 提交于
There's a name leak introduced by commit 91a27b2a ("vfs: define struct filename and have getname() return it"). Add the missing putname. [akpm@linux-foundation.org: cleanup] Signed-off-by: NXiaotian Feng <dannyfeng@tencent.com> Reviewed-by: NJeff Layton <jlayton@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
When MEMCG is configured on (even when it's disabled by boot option), when adding or removing a page to/from its lru list, the zone pointer used for stats updates is nowadays taken from the struct lruvec. (On many configurations, calculating zone from page is slower.) But we have no code to update all the lruvecs (per zone, per memcg) when a memory node is hotadded. Here's an extract from the oops which results when running numactl to bind a program to a newly onlined node: BUG: unable to handle kernel NULL pointer dereference at 0000000000000f60 IP: __mod_zone_page_state+0x9/0x60 Pid: 1219, comm: numactl Not tainted 3.6.0-rc5+ #180 Bochs Bochs Process numactl (pid: 1219, threadinfo ffff880039abc000, task ffff8800383c4ce0) Call Trace: __pagevec_lru_add_fn+0xdf/0x140 pagevec_lru_move_fn+0xb1/0x100 __pagevec_lru_add+0x1c/0x30 lru_add_drain_cpu+0xa3/0x130 lru_add_drain+0x2f/0x40 ... The natural solution might be to use a memcg callback whenever memory is hotadded; but that solution has not been scoped out, and it happens that we do have an easy location at which to update lruvec->zone. The lruvec pointer is discovered either by mem_cgroup_zone_lruvec() or by mem_cgroup_page_lruvec(), and both of those do know the right zone. So check and set lruvec->zone in those; and remove the inadequate attempt to set lruvec->zone from lruvec_init(), which is called before NODE_DATA(node) has been allocated in such cases. Ah, there was one exceptionr. For no particularly good reason, mem_cgroup_force_empty_list() has its own code for deciding lruvec. Change it to use the standard mem_cgroup_zone_lruvec() and mem_cgroup_get_lru_size() too. In fact it was already safe against such an oops (the lru lists in danger could only be empty), but we're better proofed against future changes this way. I've marked this for stable (3.6) since we introduced the problem in 3.5 (now closed to stable); but I have no idea if this is the only fix needed to get memory hotadd working with memcg in 3.6, and received no answer when I enquired twice before. Reported-by: NTang Chen <tangchen@cn.fujitsu.com> Signed-off-by: NHugh Dickins <hughd@google.com> Acked-by: NJohannes Weiner <hannes@cmpxchg.org> Acked-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Konstantin Khlebnikov <khlebnikov@openvz.org> Cc: Wen Congyang <wency@cn.fujitsu.com> Cc: <stable@vger.kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-