For better code reuse use the newly added page iterator to iterate
through the pages.  The offset, length within the page is still
calculated by the mapping iterator as well as the actual mapping.  Idea
from Tejun Heo.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add an iterator to walk through a scatter list a page at a time starting
at a specific page offset.  As opposed to the mapping iterator this is
meant to be small, performing well even in simple loops like collecting
all pages on the scatterlist into an array or setting up an iommu table
based on the pages' DMA address.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

TI LP8788 PMU supports regulators, battery charger, RTC, ADC, backlight
dri= ver and current sinks.  This patch enables LP8788 backlight module.

(Brightness mode)
The brightness is controlled by PWM input or I2C register.
All modes are supported in the driver.

(Platform data)
Configurable data can be defined in the platform side.
 name                  : backlight driver name. (default: "lcd-backlight")
 initial_brightness    : initial value of backlight brightness
 bl_mode               : brightness control by PWM or lp8788 register
 dim_mode              : dimming mode selection
 full_scale            : full scale current setting
 rise_time             : brightness ramp up step time
 fall_time             : brightness ramp down step time
 pwm_pol               : PWM polarity setting when bl_mode is PWM based
 period_ns             : platform specific PWM period value. unit is nano.

The default values are set in case no platform data is defined.

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: "devendra.aaru" <devendra.aaru@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There is only one user of bprm_mm_init, and it's inside the same file.
Signed-off-by: NYuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

very few users left...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

The following set of operations on a NFS client and server will cause

    server# mkdir a
    client# cd a
    server# mv a a.bak
    client# sleep 30  # (or whatever the dir attrcache timeout is)
    client# stat .
    stat: cannot stat `.': Stale NFS file handle

Obviously, we should not be getting an ESTALE error back there since the
inode still exists on the server. The problem is that the lookup code
will call d_revalidate on the dentry that "." refers to, because NFS has
FS_REVAL_DOT set.

nfs_lookup_revalidate will see that the parent directory has changed and
will try to reverify the dentry by redoing a LOOKUP. That of course
fails, so the lookup code returns ESTALE.

The problem here is that d_revalidate is really a bad fit for this case.
What we really want to know at this point is whether the inode is still
good or not, but we don't really care what name it goes by or whether
the dcache is still valid.

Add a new d_op->d_weak_revalidate operation and have complete_walk call
that instead of d_revalidate. The intent there is to allow for a
"weaker" d_revalidate that just checks to see whether the inode is still
good. This is also gives us an opportunity to kill off the FS_REVAL_DOT
special casing.

[AV: changed method name, added note in porting, fixed confusion re
having it possibly called from RCU mode (it won't be)]

Cc: NeilBrown <neilb@suse.de>
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

* Implement memory windows binding in mlx4_ib_post_send.

* Implement mlx4_ib_bind_mw by deferring to mlx4_ib_post_send.

* Rename MLX4_WQE_FMR_PERM_* flags to MLX4_WQE_FMR_AND_BIND_PERM_*,
  indicating that they are used both for fast registration work
  requests, and for memory window bind work requests.
Signed-off-by: NHaggai Eran <haggaie@mellanox.com>
Signed-off-by: NShani Michaeli <shanim@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Implement MW allocation and deallocation in mlx4_core and mlx4_ib.
Pass down the enable bind flag when registering memory regions.
Signed-off-by: NHaggai Eran <haggaie@mellanox.com>
Signed-off-by: NShani Michaeli <shanim@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Commit "85865c1f ima: add policy support for file system uuid"
introduced a CONFIG_BLOCK dependency.  This patch defines a
wrapper called blk_part_pack_uuid(), which returns -EINVAL,
when CONFIG_BLOCK is not defined.

security/integrity/ima/ima_policy.c:538:4: error: implicit declaration
of function 'part_pack_uuid' [-Werror=implicit-function-declaration]

Changelog v2:
- Reference commit number in patch description
Changelog v1:
- rename ima_part_pack_uuid() to blk_part_pack_uuid()
- resolve scripts/checkpatch.pl warnings
Changelog v0:
- fix UUID scripts/Lindent msgs
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Reported-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NMimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: NDavid Rientjes <rientjes@google.com>
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NJames Morris <james.l.morris@oracle.com>

Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver. Platform data is
therefore no longer required. Rework the driver to parse the device tree
directly into struct sdhci_tegra.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The tmio_mmc_cd_wakeup() inline function has been deprecated since 3.4 and
is unused since 3.4 too. Remove them.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The struct sh_mobile_sdhi_info::pdata field was only used for platform-
based card detection and isn't used anymore since the migration to GPIO-
based MMC slot functions. Remove it.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The "extern" keyword isn't required in function declarations, remove it.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

MMC defines a number of standard DT bindings. Having each driver parse
them individually adds code redundancy and is error prone. Provide a
standard function to unify the parsing. After all drivers are converted
to using it instead of their own parsers, this function can be integrated
into mmc_alloc_host().
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch supports packed write command of eMMC4.5 devices.  Several
writes can be grouped in packed command and all data of the individual
commands can be sent in a single transfer on the bus. Large amounts of
data in one transfer rather than several data of small size are
effective for eMMC write internally.  As a result, packed command help
write throughput be improved.  The following tables show the results
of packed write.

Type A:
test     none |  packed
iozone   25.8 |  31
tiotest  27.6 |  31.2
lmdd     31.2 |  35.4

Type B:
test     none |  packed
iozone   44.1 |  51.1
tiotest  47.9 |  52.5
lmdd     51.6 |  59.2

Type C:
test     none |  packed
iozone   19.5 |  32
tiotest  19.9 |  34.5
lmdd     22.8 |  40.7
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NMaya Erez <merez@codeaurora.org>
Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds packed command feature of eMMC4.5.  The maximum number
for packing read (or write) is offered and exception event relevant to
packed command which is used for error handling is enabled. If host
wants to use this feature, MMC_CAP2_PACKED_CMD should be set.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NMaya Erez <merez@codeaurora.org>
Reviewed-by: NSubhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

4d55c5a1 ("mmc: sdhci: enable preset value after uhs initialization")
added preset value support and enabled it by default during sd card init.

Below are the enhancements introduced by this patch:

1. In current code, preset value is enabled after setting clock finished,
which means the clock is manually set by driver firstly and then suddenly
switched to preset value at this point. So the first setting is useless
and unnecessary. What's more, the first clock setting may differ from the
preset one.  The better way is enable preset value just after switch to
UHS mode so the preset value can take effect immediately. So move preset
value enable from mmc_sd_init_card to sdhci_set_ios which will be called
during set timing.

2. In current code, preset value is disabled at the beginning of
mmc_attach_sd.  It's too late since low freq (400khz) should be set in
mmc_power_up.  So move preset value disable to sdhci_set_ios which will
be called during power up.

3. host->clock and ios->drv_type should also be updated according to the
preset value if it's enabled. Current code missed this.

4. This patch also introduce a quirk to disable preset value in case
preset value doesn't work.

This patch has been verified on sdhci-pxav3 platform with both preset
enabled and disabled.
Signed-off-by: NKevin Liu <kliu5@marvell.com>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This host_ops member is used to test if the card is signaling busy by
pulling dat[0:3] low.
Signed-off-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NChris Ball <cjb@laptop.org>

The i.MX esdhc has a nonstandard bit layout for the SDHCI_HOST_CONTROL
register. To support 8bit bus width on i.MX populate the platform_bus_width
callback. This is tested on an i.MX25, but should according to the datasheets
work on the other i.MX using this hardware aswell. The i.MX6, while having
a SDHCI_SPEC_300 controller, still uses the same nonstandard register layout.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Tested-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The original quirk was added in the change 'mmc: dw_mmc: add quirk to
indicate missing write protect line'.  The original quirk was added at
a controller level even though each slot has its own write protect (so
the quirk should be at the slot level).  A recent change (mmc: dw_mmc:
Add "disable-wp" device tree property) added a slot-level quirk and
support for the quirk directly to dw_mmc.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NWill Newton <will.newton@imgtec.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NChris Ball <cjb@laptop.org>

The "disable-wp" property is used to specify that a given SD card slot
doesn't have a concept of write protect.  This eliminates the need for
special case code for SD slots that should never be write protected
(like a micro SD slot or a dev board).

The dw_mmc driver is special in needing to specify "disable-wp"
because the lack of a "wp-gpios" property means to use the special
purpose write protect line.  On some other mmc devices the lack of
"wp-gpios" means that write protect should be disabled.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NWill Newton <will.newton@imgtec.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NChris Ball <cjb@laptop.org>

The right value is 54 according to eMMC 4.5 specification.
Signed-off-by: NZhangYi <yix.x.zhang@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

There are two places to call vlan_set_encap_proto():
vlan_untag() and __pop_vlan_tci().

vlan_untag() assumes skb->data points after mac addr, otherwise
the following code

        vhdr = (struct vlan_hdr *) skb->data;
        vlan_tci = ntohs(vhdr->h_vlan_TCI);
        __vlan_hwaccel_put_tag(skb, vlan_tci);

        skb_pull_rcsum(skb, VLAN_HLEN);

won't be correct. But __pop_vlan_tci() assumes points _before_
mac addr.

In vlan_set_encap_proto(), it looks for some magic L2 value
after mac addr:

        rawp = skb->data;
        if (*(unsigned short *) rawp == 0xFFFF)
	...

Therefore __pop_vlan_tci() is obviously wrong.

A quick fix is avoiding using skb->data in vlan_set_encap_proto(),
use 'vhdr+1' is always correct in both cases.

Cc: David S. Miller <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Signed-off-by: NCong Wang <amwang@redhat.com>
Acked-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In "ksm: remove old stable nodes more thoroughly" I said that I'd never
seen its WARN_ON_ONCE(page_mapped(page)).  True at the time of writing,
but it soon appeared once I tried fuller tests on the whole series.

It turned out to be due to the KSM page migration itself: unmerge_and_
remove_all_rmap_items() failed to locate and replace all the KSM pages,
because of that hiatus in page migration when old pte has been replaced
by migration entry, but not yet by new pte.  follow_page() finds no page
at that instant, but a KSM page reappears shortly after, without a
fault.

Add FOLL_MIGRATION flag, so follow_page() can do migration_entry_wait()
for KSM's break_cow().  I'd have preferred to avoid another flag, and do
it every time, in case someone else makes the same easy mistake; but did
not find another transgressor (the common get_user_pages() is of course
safe), and cannot be sure that every follow_page() caller is prepared to
sleep - ia64's xencomm_vtop()? Now, THP's wait_split_huge_page() can
already sleep there, since anon_vma locking was changed to mutex, but
maybe that's somehow excluded.
Signed-off-by: NHugh Dickins <hughd@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Petr Holasek <pholasek@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Izik Eidus <izik.eidus@ravellosystems.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This change adds a follow_page_mask function which is equivalent to
follow_page, but with an extra page_mask argument.

follow_page_mask sets *page_mask to HPAGE_PMD_NR - 1 when it encounters
a THP page, and to 0 in other cases.

__get_user_pages() makes use of this in order to accelerate populating
THP ranges - that is, when both the pages and vmas arrays are NULL, we
don't need to iterate HPAGE_PMD_NR times to cover a single THP page (and
we also avoid taking mm->page_table_lock that many times).
Signed-off-by: NMichel Lespinasse <walken@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use long type for page counts in mm_populate() so as to avoid integer
overflow when running the following test code:

int main(void) {
  void *p = mmap(NULL, 0x100000000000, PROT_READ,
                 MAP_PRIVATE | MAP_ANON, -1, 0);
  printf("p: %p\n", p);
  mlockall(MCL_CURRENT);
  printf("done\n");
  return 0;
}
Signed-off-by: NMichel Lespinasse <walken@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This variable is calculated from nr_free_pagecache_pages so
change its type to unsigned long.
Signed-off-by: NZhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently, the amount of RAM that functions nr_free_*_pages return is
held in unsigned int.  But in machines with big memory (exceeding 16TB),
the amount may be incorrect because of overflow, so fix it.
Signed-off-by: NZhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add pgdat_end_pfn() and pgdat_is_empty() helpers which match the similar
zone_*() functions.

Change node_end_pfn() to be a wrapper of pgdat_end_pfn().
Signed-off-by: NCody P Schafer <cody@linux.vnet.ibm.com>
Cc: David Hansen <dave@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Factoring out these 2 checks makes it more clear what we are actually
checking for.
Signed-off-by: NCody P Schafer <cody@linux.vnet.ibm.com>
Cc: David Hansen <dave@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add 2 helpers (zone_end_pfn() and zone_spans_pfn()) to reduce code
duplication.

This also switches to using them in compaction (where an additional
variable needed to be renamed), page_alloc, vmstat, memory_hotplug, and
kmemleak.

Note that in compaction.c I avoid calling zone_end_pfn() repeatedly
because I expect at some point the sycronization issues with start_pfn &
spanned_pages will need fixing, either by actually using the seqlock or
clever memory barrier usage.
Signed-off-by: NCody P Schafer <cody@linux.vnet.ibm.com>
Cc: David Hansen <dave@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Instead of directly utilizing a combination of config options to determine
this, add a macro to specifically address it.
Signed-off-by: NCody P Schafer <cody@linux.vnet.ibm.com>
Cc: David Hansen <dave@linux.vnet.ibm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

An inactive file list is considered low when its active counterpart is
bigger, regardless of whether it is a global zone LRU list or a memcg
zone LRU list.  The only difference is in how the LRU size is assessed.

get_lru_size() does the right thing for both global and memcg reclaim
situations.

Get rid of inactive_file_is_low_global() and
mem_cgroup_inactive_file_is_low() by using get_lru_size() and compare
the numbers in common code.
Signed-off-by: NJohannes Weiner <hannes@cmpxchg.org>
Acked-by: NMichal Hocko <mhocko@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

No functional change, but the only purpose of the offlining argument to
migrate_pages() etc, was to ensure that __unmap_and_move() could migrate a
KSM page for memory hotremove (which took ksm_thread_mutex) but not for
other callers.  Now all cases are safe, remove the arg.
Signed-off-by: NHugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Petr Holasek <pholasek@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Izik Eidus <izik.eidus@ravellosystems.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Switching merge_across_nodes after running KSM is liable to oops on stale
nodes still left over from the previous stable tree.  It's not something
that people will often want to do, but it would be lame to demand a reboot
when they're trying to determine which merge_across_nodes setting is best.

How can this happen?  We only permit switching merge_across_nodes when
pages_shared is 0, and usually set run 2 to force that beforehand, which
ought to unmerge everything: yet oopses still occur when you then run 1.

Three causes:

1. The old stable tree (built according to the inverse
   merge_across_nodes) has not been fully torn down.  A stable node
   lingers until get_ksm_page() notices that the page it references no
   longer references it: but the page is not necessarily freed as soon as
   expected, particularly when swapcache.

   Fix this with a pass through the old stable tree, applying
   get_ksm_page() to each of the remaining nodes (most found stale and
   removed immediately), with forced removal of any left over.  Unless the
   page is still mapped: I've not seen that case, it shouldn't occur, but
   better to WARN_ON_ONCE and EBUSY than BUG.

2. __ksm_enter() has a nice little optimization, to insert the new mm
   just behind ksmd's cursor, so there's a full pass for it to stabilize
   (or be removed) before ksmd addresses it.  Nice when ksmd is running,
   but not so nice when we're trying to unmerge all mms: we were missing
   those mms forked and inserted behind the unmerge cursor.  Easily fixed
   by inserting at the end when KSM_RUN_UNMERGE.

3.  It is possible for a KSM page to be faulted back from swapcache
   into an mm, just after unmerge_and_remove_all_rmap_items() scanned past
   it.  Fix this by copying on fault when KSM_RUN_UNMERGE: but that is
   private to ksm.c, so dissolve the distinction between
   ksm_might_need_to_copy() and ksm_does_need_to_copy(), doing it all in
   the one call into ksm.c.

A long outstanding, unrelated bugfix sneaks in with that third fix:
ksm_does_need_to_copy() would copy from a !PageUptodate page (implying I/O
error when read in from swap) to a page which it then marks Uptodate.  Fix
this case by not copying, letting do_swap_page() discover the error.
Signed-off-by: NHugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Petr Holasek <pholasek@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Izik Eidus <izik.eidus@ravellosystems.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Acked-by: NMel Gorman <mgorman@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The function names page_xchg_last_nid(), page_last_nid() and
reset_page_last_nid() were judged to be inconsistent so rename them to a
struct_field_op style pattern.  As it looked jarring to have
reset_page_mapcount() and page_nid_reset_last() beside each other in
memmap_init_zone(), this patch also renames reset_page_mapcount() to
page_mapcount_reset().  There are others like init_page_count() but as
it is used throughout the arch code a rename would likely cause more
conflicts than it is worth.

[akpm@linux-foundation.org: fix zcache]
Signed-off-by: NMel Gorman <mgorman@suse.de>
Suggested-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Andrew Morton pointed out that page_xchg_last_nid() and
reset_page_last_nid() were "getting nuttily large" and asked that it be
investigated.

reset_page_last_nid() is on the page free path and it would be
unfortunate to make that path more expensive than it needs to be.  Due
to the internal use of page_xchg_last_nid() it is already too expensive
but fortunately, it should also be impossible for the page->flags to be
updated in parallel when we call reset_page_last_nid().  Instead of
unlining the function, it uses a simplier implementation that assumes no
parallel updates and should now be sufficiently short for inlining.

page_xchg_last_nid() is called in paths that are already quite expensive
(splitting huge page, fault handling, migration) and it is reasonable to
uninline.  There was not really a good place to place the function but
mm/mmzone.c was the closest fit IMO.

This patch saved 128 bytes of text in the vmlinux file for the kernel
configuration I used for testing automatic NUMA balancing.
Signed-off-by: NMel Gorman <mgorman@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>