Convert Linux PAT entries into Xen ones when constructing ptes.  Linux
doesn't use _PAGE_PAT for ptes, so the only difference in the first 4
entries is that Linux uses _PAGE_PWT for WC, whereas Xen (and default)
use it for WT.

xen_pte_val does the inverse conversion.

We hard-code assumptions about Linux's current PAT layout, but a
warning on the wrmsr to MSR_IA32_CR_PAT should point out any problems.
If necessary we could go to a more general table-based conversion between
Linux and Xen PAT entries.

hugetlbfs poses a problem at the moment, the x86 architecture uses the
same flag for _PAGE_PAT and _PAGE_PSE, which changes meaning depending
on which pagetable level we're using.  At the moment this should be OK
so long as nobody tries to do a pte_val on a hugetlbfs pte.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

Keep xen_max_p2m_pfn up to date with the end of the extra memory
we're adding.  It is possible that it will be too high since memory
may be truncated by a "mem=" option on the kernel command line, but
that won't matter.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

If extra memory is very much larger than the base memory size
then all of the base memory can be filled with structures reserved to
describe the extra memory, leaving no space for anything else.

Even at the maximum ratio there will be little space for anything else,
but this change is intended to at least allow the system to boot rather
than crash mysteriously.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

If an entire E820 RAM region is beyond mem_end, still add its
pages to the extra area so that space can be used by the kernel.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

If Xen gives us non-RAM E820 entries (dom0 only, typically), then
make sure the extra RAM region is beyond them.  It's OK for
the extra space to grow into E820 regions, however.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

When using the e820 map to get the initial pseudo-physical address space,
look for either Xen-provided memory which doesn't lie within an E820
region, or an E820 RAM region which extends beyond the Xen-provided
memory range.

Count these pages, and add them to a new "extra memory" range.  This range
has an E820 RAM range to describe it - so the kernel will allocate page
structures for it - but it is also marked reserved so that the kernel
will not attempt to use it.

The balloon driver can then add this range as a set of currently
ballooned-out pages, which can be used to extend the domain beyond its
original size.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

Rather than simply using a flat memory map from Xen, use its provided
E820 map.  This allows the domain builder to tell the domain to reserve
space for more pages than those initially provided at domain-build time.

It also allows the host to specify holes in the address space (for
PCI-passthrough, for example).
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

When setting up a pte for a missing pfn (no matching mfn), just create
an empty pte rather than a junk mapping.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

When building mfn parts of p2m structure, we rely on being able to
use mfn_to_virt, which in turn requires kernel to be mapped into
the linear area (which is distinct from the kernel image mapping
on 64-bit).  Defer calling xen_build_mfn_list_list() until after
xen_setup_kernel_pagetable();
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

set_phys_to_machine() can return false on failure, which means a memory
allocation failure for the p2m structure.  It can only fail if setting
the mfn for a pfn in previously unused address space.  It is guaranteed
to succeed if you're setting a mapping to INVALID_P2M_ENTRY or updating
the mfn for an existing pfn.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

Make the p2m structure a 3 level tree which covers the full possible
physical space.

The p2m structure contains mappings from the domain's pfns to system-wide
mfns.  The structure has 3 levels and two roots.  The first root is for
the domain's own use, and is linked with virtual addresses.  The second
is all mfn references, and is used by Xen on save/restore to allow it to
update the p2m mapping for the domain.

At boot, the domain builder provides a simple flat p2m array for all the
initially present pages.  We construct the two levels above that using
the early_brk allocator.  After early boot time, set_phys_to_machine()
will allocate any missing levels using the normal kernel allocator
(at GFP_KERNEL, so it must be called in a normal blocking context).

Because the early_brk() API requires us to pre-reserve the maximum amount
of memory we could allocate, there is still a CONFIG_XEN_MAX_DOMAIN_MEMORY
config option, but its only negative side-effect is to increase the
kernel's apparent bss size.  However, since all unused brk memory is
returned to the heap, there's no real downside to making it large.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

Change event delivery to:
 - mask+clear event in the upcall function
 - use handle_fasteoi_irq as the handler
 - unmask in the eoi function (and handle migration)
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

Allocate p2m tables based on the actual runtime maximum pfn rather than
the static config-time limit.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

Use early brk mechanism to allocate p2m tables, to save memory when
booting non-Xen.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

Useful when converting static arrays into boottime brk allocated objects.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

Tony Luck reports that the addition of the access_ok() check in commit
0eead9ab ("Don't dump task struct in a.out core-dumps") broke the
ia64 compile due to missing the necessary header file includes.

Rather than add yet another include (<asm/unistd.h>) to make everything
happy, just uninline the silly core dump helper functions and move the
bodies to fs/exec.c where they make a lot more sense.

dump_seek() in particular was too big to be an inline function anyway,
and none of them are in any way performance-critical.  And we really
don't need to mess up our include file headers more than they already
are.
Reported-and-tested-by: NTony Luck <tony.luck@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  ehea: Fix a checksum issue on the receive path
  net: allow FEC driver to use fixed PHY support
  tg3: restore rx_dropped accounting
  b44: fix carrier detection on bind
  net: clear heap allocations for privileged ethtool actions
  NET: wimax, fix use after free
  ATM: iphase, remove sleep-inside-atomic
  ATM: mpc, fix use after free
  ATM: solos-pci, remove use after free
  net/fec: carrier off initially to avoid root mount failure
  r8169: use device model DMA API
  r8169: allocate with GFP_KERNEL flag when able to sleep

akiphie points out that a.out core-dumps have that odd task struct
dumping that was never used and was never really a good idea (it goes
back into the mists of history, probably the original core-dumping
code).  Just remove it.

Also do the access_ok() check on dump_write().  It probably doesn't
matter (since normal filesystems all seem to do it anyway), but he
points out that it's normally done by the VFS layer, so ...

[ I suspect that we should possibly do "vfs_write()" instead of
  calling ->write directly.  That also does the whole fsnotify and write
  statistics thing, which may or may not be a good idea. ]

And just to be anal, do this all for the x86-64 32-bit a.out emulation
code too, even though it's not enabled (and won't currently even
compile)
Reported-by: Nakiphie <akiphie@lavabit.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
  ioat2: fix performance regression

* 'for-2.6.36' of git://linux-nfs.org/~bfields/linux:
  nfsd: fix BUG at fs/nfsd/nfsfh.h:199 on unlink

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  ring-buffer: Fix typo of time extends per page
  perf, MIPS: Support cross compiling of tools/perf for MIPS
  perf: Fix incorrect copy_from_user() usage

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: relax ioremap prohibition (309caa9c) for -final and -stable
  ARM: 6440/1: ep93xx: DMA: fix channel_disable
  cpuimx27: fix i2c bus selection
  cpuimx27: fix compile when ULPI is selected
  ARM: 6435/1: Fix HWCAP_TLS flag for ARM11MPCore/Cortex-A9
  ARM: 6436/1: AT91: Fix power-saving in idle-mode on 926T processors
  ARM: fix section mismatch warnings in Versatile Express
  ARM: 6412/1: kprobes-decode: add support for MOVW instruction
  ARM: 6419/1: mmu: Fix MT_MEMORY and MT_MEMORY_NONCACHED pte flags
  ARM: 6416/1: errata: faulty hazard checking in the Store Buffer may lead to data corruption

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  omap: iommu-load cam register before flushing the entry

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/radeon/kms: Silent spurious error message
  drm/radeon/kms: fix bad cast/shift in evergreen.c
  drm/radeon/kms: make TV/DFP table info less verbose
  drm/radeon/kms: leave certain CP int bits enabled
  drm/radeon/kms: avoid corner case issue with unmappable vram V2

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, numa: For each node, register the memory blocks actually used
  x86, AMD, MCE thresholding: Fix the MCi_MISCj iteration order
  x86, mce, therm_throt.c: Fix missing curly braces in error handling logic

Commit 07934481 "DMAENGINE: generic channel status v2" changed the interface for
how dma channel progress is retrieved.  It inadvertently exported an internal
helper function ioat_tx_status() instead of ioat_dma_tx_status().  The latter
polls the hardware to get the latest completion state, while the helper just
evaluates the current state without touching hardware.  The effect is that we
end up waiting for completion timeouts or descriptor allocation errors before
the completion state is updated.

iperf (before fix):
[SUM]  0.0-41.3 sec   364 MBytes  73.9 Mbits/sec

iperf (after fix):
[SUM]  0.0- 4.5 sec   499 MBytes   940 Mbits/sec

This is a regression starting with 2.6.35.

Cc: <stable@kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Reported-by: NRichard Scobie <richard@sauce.co.nz>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Currently we set all skbs with CHECKSUM_UNNECESSARY, even
those whose protocol we don't know. This patch just
add the CHECKSUM_COMPLETE tag for non TCP/UDP packets.
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As of commit 43a9aa64 "NFSD:
Fill in WCC data for REMOVE, RMDIR, MKNOD, and MKDIR", we sometimes call
fh_unlock on a filehandle that isn't fully initialized.

We should fix up the callers, but as a quick fix it is also sufficient
just to remove this assertion.
Reported-by: NMarius Tolzmann <tolzmann@molgen.mpg.de>
Cc: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>

At least one board using the FEC driver does not have a conventional
PHY attached to it, it is directly connected to a somewhat simple
ethernet switch (the board is the SnapGear/LITE, and the attached
4-port ethernet switch is a RealTek RTL8305). This switch does not
present the usual register interface of a PHY, it presents nothing.
So a PHY scan will find nothing - it finds ID's of 0 for each PHY
on the attached MII bus.

After the FEC driver was changed to use phylib for supporting PHYs
it no longer works on this particular board/switch setup.

Add code support to use a fixed phy if no PHY is found on the MII bus.
This is based on the way the cpmac.c driver solved this same problem.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

... but produce a big warning about the problem as encouragement
for people to fix their drivers.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

When channel_disable() is called, it disables per channel interrupts and
waits until channels state becomes STATE_STALL, and then disables the
channel. Now, if the DMA transfer is disabled while the channel is in
STATE_NEXT we will not wait anything and disable the channel immediately.
This seems to cause weird data corruption for example in audio transfers.

Fix is to wait while we are in STATE_NEXT or STATE_ON and only then
disable the channel.
Signed-off-by: NMika Westerberg <mika.westerberg@iki.fi>
Acked-by: NRyan Mallon <ryan@bluewatersys.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

* 'kvm-updates/2.6.36' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: Move TSC reset out of vmcb_init
  KVM: x86: Fix SVM VMCB reset