tdi_reset is already taking care of setting host mode for tdi devices.
Don't duplicate code in platform driver.

Make ehci_halt a nop if the controller is not in host mode (otherwise it 
will fail), and let's ehci_reset do the tdi_reset.
We need to move hcd->has_tt flags before ehci_halt, in order ehci_halt 
knows we are a tdi device.


Before the setup routine was doing :
- put controller in host mode
- ehci_halt
- ehci_init
- hcd->has_tt = 1;
- ehci_reset

Now we do :
- hcd->has_tt = 1;
- ehci_halt
- ehci_init
- ehci_reset

PS : now we handle correctly the device -> host transition.
Signed-off-by: NMatthieu CASTET <matthieu.castet@parrot.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1407) fixes a bug in ehci-hcd's isochronous scheduler.
All its calculations should be done in terms of microframes, but for
full-speed devices, sched->span is stored in frames.  It needs to be
converted.

This fix is liable to expose problems in other drivers.  The old code
would accept URBs that should not have been accepted, so drivers have
had no reason to avoid submitting URBs that exceeded the maximum
schedule length.  In an attempt to partially compensate for this, the
patch also adjusts the schedule length from a minimum of 256 frames up
to a minimum of 512 frames.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If we use the HCD_LOCAL_MEM flag and dma_declare_coherent_memory() to
enforce the host controller's local memory utilization we also need to
disable native scatter-gather support, otherwise hcd_alloc_coherent() in
map_urb_for_dma() is called with urb->transfer_buffer == NULL, that
triggers a NULL pointer dereference.

We can also consider to add a WARN_ON() and return an error code to
better catch this problem in the future.

At the moment no driver seems to hit this bug, so I should
consider this a low-priority fix.
Signed-off-by: NAndrea Righi <arighi@develer.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1393) converts several of the single-bit fields in
struct usb_hcd to atomic flags.  This is for safety's sake; not all
CPUs can update bitfield values atomically, and these flags are used
in multiple contexts.

The flag fields that are set only during registration or removal can
remain as they are, since non-atomic accesses at those times will not
cause any problems.

(Strictly speaking, the authorized_default flag should become atomic
as well.  I didn't bother with it because it gets changed only via
sysfs.  It can be done later, if anyone wants.)
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch will enable Per-port event feature defined in EHCI 1.1
addendum. This feature addresses an issue where HCD is currently
required to read and parse PORTSC for all enabled root hub ports. With
this patch, the overhead will be reduced.
Signed-off-by: NAlek Du <alek.du@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

With this patch, the LPM capable EHCI host controller can put device
into L1 sleep state which is a mode that can enter/exit quickly, and
reduce power consumption.
Signed-off-by: NJacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: NAlek Du <alek.du@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

EHCI 1.1 addendum introduced several energy efficiency extensions for
EHCI USB host controllers:
1. LPM (link power management)
2. Per-port change
3. Shorter periodic frame list
4. Hardware prefetching

This patch is intended to define the HW bits and debug interface for
EHCI 1.1 addendum. The LPM and Per-port change patches will be sent out
after this patch.
Signed-off-by: NJacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: NAlek Du <alek.du@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Greg prefers this to go through the trivial tree.
http://lkml.org/lkml/2010/6/24/1

There are about 2500 void functions in drivers/usb
Only a few used return; at end of function.

Standardize them a bit.

Moved a statement down a line in drivers/usb/host/u132-hcd.c
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch fixes the driver to allow both CONFIG_USB_EHCI_HCD_PPC_OF and
CONFIG_USB_ECHI_HCD_XILINX to be selected.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
CC: John Linn <john.linn@xilinx.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hcd.h from drivers/usb/core into include/linux/usb/
Signed-of-by: NEric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1369) fixes a problem in ehci-hcd.  Some controllers
occasionally run into trouble when the driver reclaims siTDs too
quickly.  This can happen while streaming audio; it causes the
controller to crash.

The patch changes siTD reclamation to work the same way as iTD
reclamation: Completed siTDs are stored on a list and not reused until
at least one frame has passed.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NNate Case <ncase@xes-inc.com>
CC: <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>

The EHCI driver stores in usb_host_endpoint.hcpriv a pointer to either
an ehci_qh or an ehci_iso_stream structure, and uses the contents of the
hw_info1 field to distinguish the two cases.

After ehci_qh was split into hw and sw parts, ehci_iso_stream must also
be adjusted so that it again looks like an ehci_qh structure.

This fixes a NULL pointer access in ehci_endpoint_disable() when it
tries to access qh->hw->hw_info1.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Reported-by: NColin Fletcher <colin.m.fletcher@googlemail.com>
Cc: stable <stable@kernel.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Replace ARCH_OMAP34XX with ARCH_OMAP3
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch (as1330) fixes a bug in khbud's handling of remote
wakeups.  When a device sends a remote-wakeup request, the parent hub
(or the host controller driver, for directly attached devices) begins
the resume sequence and notifies khubd when the sequence finishes.  At
this point the port's SUSPEND feature is automatically turned off.

However the device needs an additional 10-ms resume-recovery time
(TRSMRCY in the USB spec).  Khubd does not wait for this delay if the
SUSPEND feature is off, and as a result some devices fail to behave
properly following a remote wakeup.  This patch adds the missing
delay to the remote-wakeup path.

It also extends the resume-signalling delay used by ehci-hcd and
uhci-hcd from 20 ms (the value in the spec) to 25 ms (the value we use
for non-remote-wakeup resumes).  The extra time appears to help some
devices.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Cc: Rickard Bellini <rickard.bellini@ericsson.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1300) adds native scatter-gather support to ehci-hcd.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The Freescale MX27 and MX31 SoCs have a EHCI controller onboard.
The controller is capable of USB on the go. This patch adds
a driver to support all three of them.

Users have to pass details about serial interface configuration in the
platform data.

The USB OTG core used here is the ARC core, so the driver should
be renamed and probably be merged with ehci-fsl.c eventually.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The EHCI specification says that an EHCI host controller may cache part of
the isochronous schedule.  The EHCI controller must advertise how much it
caches in the schedule through the HCCPARAMS register isochronous
scheduling threshold (IST) bits.

In theory, adding new iTDs within the IST should be harmless.  The HW will
follow the old cached linked list and miss the new iTD.  SW will notice HW
missed the iTD and return 0 for the transfer length.

However, Intel ICH9 chipsets (and some later chipsets) have issues when SW
attempts to schedule a split transaction within the IST.  All transfers
will cease being sent out that port, and the drivers will see isochronous
packets complete with a length of zero.  Start of frames may or may not
also disappear, causing the device to go into auto-suspend.  This "bus
stall" will continue until a control or bulk transfer is queued to a
device under that roothub.

Most drivers will never cause this behavior, because they use multiple
URBs with multiple packets to keep the bus busy.  If you limit the number
of URBs to one, you may be able to hit this bug.

Make sure the EHCI driver does not schedule full-speed transfers within
the IST under an Intel chipset.  Make sure that when we fall behind the
current microframe plus IST, we schedule the new transfer at the next
periodic interval after the IST.

Don't change the scheduling for new transfers, since the schedule slop will
always be greater than the IST.  Allow high speed isochronous transfers to
be scheduled within the IST, since this doesn't trigger the Intel chipset
bug.

Make sure that if the host caches the full frame, the EHCI driver's
internal isochronous threshold (ehci->i_thresh) is set to
8 microframes + 2 microframes wiggle room.  This is similar to what is done in
the case where the host caches less than the full frame.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this driver has been sitting in linux-omap tree for quite
some time. It adds support for omap's ehci controller.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add bus glue driver for Xilinx USB host controller. The controller can be
configured as HS only or HS/FS hybrid. The driver uses the device tree file
to configure the driver according to the setting in the hardware system.

This driver has been tested with usbtest using the NET2280 PCI card.
Signed-off-by: NJulie Zhu <julie.zhu@xilinx.com>
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The correct word is handshake.
Signed-off-by: NOzan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

a quirky chipset needs periodic schedules to run for a minimum
time before they can be disabled again. This enforces the requirement
with a time stamp and a calculated delay
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the EHCI debug port is initialized and in use, the EHCI host
controller driver must follow two rules.

1) If the EHCI host driver issues a controller reset, the debug
   controller driver re-initialization must get called after the reset
   is completed.

2) The EHCI host driver should ignore any requests to the physical
   EHCI debug port when the EHCI debug port is in use.

The code to check for the debug port was moved from ehci_pci_reinit()
to ehci_pci_setup because it must get called prior to ehci_reset()
which will clear the debug port registers.
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: dbrownell@users.sourceforge.net
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1281) changes the way ehci-hcd deschedules interrupt
QHs, copying the approach used for async QHs.  The caller is no longer
responsible for rescheduling the QH if its queue is non-empty; instead
the reschedule is done directly by intr_deschedule(), after calling
qh_completions().  This is exactly the same as how end_unlink_async()
works.

ehci_urb_dequeue() and intr_deschedule() now correctly handle the case
where they are called while another interrupt URB for the same QH is
being given back.  This was a surprisingly large blind spot.  And
scan_periodic() now respects the new needs_rescan flag.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1280) fixes an obscure bug in ehci-hcd's dequeuing logic
for async URBs.  If a later URB is unlinked and the completion
routine unlinks an earlier URB, then the earlier URB won't be given
back in a timely manner because the endpoint queue isn't rescanned as
it should be.

Similar bugs occur if an endpoint is reset or a halt is cleared while
a completion routine is running, because the subroutines don't test
for the COMPLETING state.

All these problems are solved by adding a new needs_rescan flag to the
ehci_qh structure.  If the flag is set while scanning through an idle
QH, the scan will be repeated.  If the QH isn't idle then an unlink
cycle will be initiated, and the proper action will be taken when it
becomes idle.

Also, an unnecessary test is removed from qh_link_async(): That
routine is never called if the QH's state isn't IDLE.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

EHCI: OHCI: Remove unnecessary includes of reboot.h
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add host USB High speed driver for at91sam9g45 series.
The host driver is an EHCI with its companion OHCI. EHCI is
handled by the new ehci-atmel.c whereas the OHCI is always
handled by ohci-at91.c.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>

The Intel Moorestown EHCI controller supports non-standard HOSTPCx register
extension. This register controls the LPM behaviour and controls the behaviour
of each USB port.
Signed-off-by: NJacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: NAlek Du <alek.du@intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The ehci_qh structure merged hw and sw together which is not good:
1. More and more items are being added into ehci_qh, the ehci_qh software
   part are unnecessary to be allocated in DMA qh_pool.
2. If HCD has local SRAM, the sw part will consume it too, and it won't
   bring any benefit.
3. For non-cache-coherence system, the entire ehci_qh is uncachable, actually
   we only need the hw part to be uncacheable. Spliting them will let the sw
   part to be cacheable.
Signed-off-by: NAlek Du <alek.du@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Basically the io watchdog is only useful for those quirk HCDs. For most
good ones, it only brings unnecessary wakeups.  At least, I know the
Intel EHCI HCDs should turn off the flag.
Signed-off-by: NAlek Du <alek.du@intel.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add ehci support for w90p910 platform.
Signed-off-by: NWan ZongShun <mcuos.com@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1273) fixes two(!) bugs introduced by the new
Clear-TT-Buffer implementation in ehci-hcd.

	It is now possible for an idle QH to have some URBs on its
	queue -- this will happen if a Clear-TT-Buffer is pending for
	the QH's endpoint.  Consequently we should not issue a warning
	when someone tries to unlink an URB from an idle QH; instead
	we should process the request immediately.

	The refcounts for QHs could get messed up, because
	submit_async() would increment the refcount when calling
	qh_link_async() and qh_link_async() would then refuse to link
	the QH into the schedule if a Clear-TT-Buffer was pending.
	Instead we should increment the refcount only when the QH
	actually is added to the schedule.  The current code tries to
	be clever by leaving the refcount alone if an unlink is
	immediately followed by a relink; the patch changes this to an
	unconditional decrement and increment (although they occur in
	the opposite order).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: NManuel Lauss <manuel.lauss@gmail.com>
Tested-by: NMatthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1256) changes ehci-hcd and all the other drivers in the
EHCI family to make use of the new clear_tt_buffer callbacks.  When a
Clear-TT-Buffer request is in progress for a QH, the QH is not allowed
to be linked into the async schedule until the request is finished.
At that time, if there are any URBs queued for the QH, it is linked
into the async schedule.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is an update to the "usb-ehci-update-toggle-state-for-linked-qhs"
patch.  Since an HCD's endpoint_reset method can be called in
interrupt context, it mustn't assume that interrupts are enabled or
that it can sleep.

So we revert to the original way of refreshing QHs' toggle bits.  Now
the endpoint_reset method merely clears the toggle flag in the device
structure (as was done before) and starts an async QH unlink.  When the
QH is linked again, after the unlink finishes and an URB is queued,
the qh_refresh() routine will update the QH's toggle bit.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NDavid <david@unsolicited.net>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1245) fixes a bug in ehci-hcd.  When an URB is queued
for an endpoint whose QH is already in the LINKED state, the QH
doesn't get refreshed.  As a result, if usb_clear_halt() was called
during the time that the QH was linked but idle, the data toggle value
in the QH doesn't get reset.

The symptom is that after a clear_halt, data gets lost and transfers
time out.  This problem is starting to show up now because the
"ehci-hcd unlink speedups" patch causes QHs with no queued URBs to
remain linked for a suitable time.

The patch utilizes the new endpoint_reset mechanism to fix the
problem.  When an endpoint is reset, the new method forcibly unlinks
the QH (if necessary) and safely updates the toggle value.  This
allows qh_update() to be simplified and avoids using usb_device's
toggle bits in a rather unintuitive way.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: NDavid <david@unsolicited.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

All usb debugfs files should be behind the usb directory, not at the
root of debugfs.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)

Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch (as1205) moves timer_action() from ehci.h to ehci-hcd.c and
makes it out-of-line.  Over the years it has grown too big to be inline
any more.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently ITDs are immediately recycled whenever their URB completes.
However, EHCI hardware can sometimes remember some ITD state.  This
means that when the ITD is reused before end-of-frame it may sometimes
cause the hardware to reference bogus state.

This patch defers reusing such ITDs by moving them into a new ehci member
cached_itd_list. ITDs resting in cached_itd_list are moved back into their
stream's free_list once scan_periodic() detects that the active frame has
elapsed.

This makes the snd_usb_us122l driver (in kernel since .28) work right
when it's hooked up through EHCI.

[ dbrownell@users.sourceforge.net: comment fixups ]
Signed-off-by: NKarsten Wiese <fzu@wemgehoertderstaat.de>
Tested-by: NPhilippe Carriere <philippe-f.carriere@wanadoo.fr>
Tested-by: NFederico Briata <federicobriata@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1165) makes a few small changes in the logic used by
ehci-hcd when it encounters a controller error:

	Instead of printing out the masked status, it prints the
	original status as read directly from the hardware.

	It doesn't check for the STS_HALT status bit before taking
	action.  The mere fact that the STS_FATAL bit is set means
	that something bad has happened and the controller needs to
	be reset.  With the old code this test could never succeed
	because the STS_HALT bit was masked out from the status.

I anticipate that this will prevent the occasional "irq X: nobody cared"
problem people encounter when their EHCI controllers die.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>