Call Trace:
 [<ffffffff81341687>] dump_stack+0x6b/0xa4
 [<ffffffff810c3e30>] ? print_irqtrace_events+0xd0/0xe0
 [<ffffffff8109e3c3>] ___might_sleep+0x183/0x240
 [<ffffffff8109e4d2>] __might_sleep+0x52/0x90
 [<ffffffff811fe17b>] kmem_cache_alloc_trace+0x5b/0x300
 [<ffffffff810c666b>] ? __lock_acquired+0x30b/0x420
 [<ffffffffa0733c28>] qla2x00_alloc_fcport+0x38/0x2a0 [qla2xxx]
 [<ffffffffa07217f4>] ? qla2x00_do_work+0x34/0x2b0 [qla2xxx]
 [<ffffffff816cc82b>] ? _raw_spin_lock_irqsave+0x7b/0x90
 [<ffffffffa072169a>] ? qla24xx_create_new_sess+0x3a/0x160 [qla2xxx]
 [<ffffffffa0721723>] qla24xx_create_new_sess+0xc3/0x160 [qla2xxx]
 [<ffffffff810c91ed>] ? trace_hardirqs_on+0xd/0x10
 [<ffffffffa07218f8>] qla2x00_do_work+0x138/0x2b0 [qla2xxx]
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If there are IO's running and host reset or chip reset is triggered,
IO's can fail due to rport time out. During chip reset recovery process,
driver notifies the transport layer that remote port no longer exist, by
calling fc_remote_port_delete(). When this function is called, it
actually delays deletion by "blocking" it. It sets the remote port state
to "FC_PORTSTATE_BLOCKED" and sets FC_RPORT_DEVLOSS_PENDING.  When
driver tries to abort the command by calling its abort handler function,
abort handler will wait until remote port state is blocked state or wait
for dev_loss_tmo time. Due to this blocking, rport times out and results
in an IO failure. This patch adds a check for any active reset process
before calling abort handler function.

[mkp: typo]
Signed-off-by: NSawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

ql2xmaxqdepth is the module parameter that seeds the per target
queue depth in the Scsi midlayer (sdev->queue_depth). Performance
testing revealed that increasing this value would improve IOPS
numbers under certain workloads.
Signed-off-by: NMichael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJoe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NJoe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Calling sp->free() ensures the context-correct free routine is called.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

SFP can come in 2 formats: short range/SR and long range/LR.  For LR,
user the can increase the number of Buffer to Buffer credits between end
points via Cavium's command line tool.  By default, FW uses a lower BB
Credit value optimized for SR.  This patch will read the SFP for each
link up event and during chip reset sequence. If the SFP type and
setting are mismatch, then the chip is reset 1 time to use the
appropriate setting.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Update ha->wq max_active from 1 to default. MQ interrupts are queued up
via this work queue. This allows interrupts to be process in parrallel,
instead of serialized by the work queue.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Driver will perform following

- Set PFLG_DRIVER_REMOVING flag and do not disable PCIe error reporting
  during adapter shutdown.
- If PCIe device count is already zero, return correct error type from
  PCI error interface.
- When device is offline, return correct error type from PCIe error
  path.
- If there is board disable thread active during shutdown and PCIe
  device count is zero then cancel scheduling board disable thread
  during shutdown and return.
Signed-off-by: NSawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The driver held spinlocks during callbacks for NVME errors which
resulted in a deadlock because recovery LS cmds needed the same lock.
Signed-off-by: NDuane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add support to the driver to set the exchange threshold value for
the number of outstanding AENs.
Signed-off-by: NDuane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: NDarren Trapp <darren.trapp@cavium.com>
Signed-off-by: NAnil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch does not change any functionality.

Following cleanups have been done as requested by reviewer

- Changed waitQ --> waitq
- Collapsed multiple debug statements into single
- Remove extra parentheses in if-else as per operator precedence
- Remove unnecessary casting

Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This code provides the interfaces to register remote and local ports of
FC4 type 0x28 with the FC-NVMe transport and transports the requests
(FC-NVMe FC link services and FC-NVMe commands IUs) to the fabric. It
also provides the support for allocating h/w queues and aborting FC-NVMe
FC requests.
Signed-off-by: NDarren Trapp <darren.trapp@cavium.com>
Signed-off-by: NDuane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: NAnil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds logic to handle the completion of FC-NVMe commands and
creates a sub-command in the SRB command structure to manage NVMe
commands.
Signed-off-by: NDarren Trapp <darren.trapp@cavium.com>
Signed-off-by: NDuane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: NAnil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added logic to change the login process into an optional PRIL step for
FC-NVMe ports as a separate operation, such that we can change type to
0x28 (NVMe).

Currently, the driver performs the PLOGI/PRLI together as one operation,
but if the discovered port is an NVMe port then we first issue the PLOGI
and then we issue the PRLI. Also, the fabric discovery logic was changed
to mark each discovered FC NVMe port, so that we can register them with
the FC-NVMe transport later.
Signed-off-by: NDarren Trapp <darren.trapp@cavium.com>
Signed-off-by: NDuane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: NAnil Gurumurthy <anil.gurumurhty@cavium.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add missing memory dump of Exchange Offload and Extended login into FW
dump.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add call back to door bell for qpair. This help reduce access to
qla_hw_data structure, in order to reduce cach thrash.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For ISP27XX, use shadow register to read FW provided REQQ's consumer
index.  The shadow register is dma'ed by firmware.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

- Move chip_reset, enable_class_2 fields from qla_hw_data to qla_qpair
  to reduce cache thrash for target MQ.
- Optimizations to reduce unnecessary memory load for good path io.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In target mode driver, queue pairs are not created during driver load
time, instead they are created at the configuration time after chip
reset.  If a user tries to load/unload driver after queue pairs are
created, then there would be mailbox failure, while deleting queue
pairs.  Flag is added to check if queue pairs are created or not. Queue
pairs will be deleted only If they were created during target
configuration.
Signed-off-by: NSawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Enable Multi Queue for Target mode. At Initiator LUN scan time, each LUN
is assign to a QPair. Each QPair is affinitize to certain CPU. When new
cmd arrives from the wire, the lunid is used to search for qpair. The
qpair's affinitized cpuid will be used to queue up the work element.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In Current code, Req Q 0, RespQ 0 & hardware_lock are the main resources
for sending and process completion of Target IO. These resources are now
referenced behind a new qpair/"struct qla_qpair base_qpair".  Main path
IO handle will access those resources via the qpair pointer in
preparation for Target MQ.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Merge active/outstanding cmd arrays from target side and initiator side
together in prepration for Target Multi Queue support.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Previously, the ql2xexchoffld module parameter was used to control the
max number of exchanges to be offload onto host memory.

Module parameter ql_dm_tgt_ex_pct was used to control the percentage of
exchanges allocated to the Target side.

With this patch, module parameter ql_dm_tgt_ex_pct is no longer used to
control exchanges for the driver. New module parameter ql2xiniexchg is
added to control exchanges between target mode and initiator mode.

With the updated module parameters, users can control the exact number
of exchanges for either Initiator or Target. The exchange offload
feature will be automatically enabled when the total number of exchanges
exceeds 2048 limit.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Assign unique id to all traces and logs for debug purpose.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Hung task timeouts can result if a qlogic board breaks unexpectedly
while running I/O. These tasks become hung because command srb reference
counts are not going to zero, hence the affected srbs and commands do
not get freed. This fix accounts for this extra reference in the srbs in
the case of a board failure.

Fixes: a465537a ("qla2xxx: Disable the adapter and skip error recovery in case of register disconnect")
Signed-off-by: NBill Kuzeja <william.kuzeja@stratus.com>
Acked-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fixes following signature in the stack trace:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000374
IP: [<ffffffffa06ec8eb>] qla2x00_sp_free_dma+0xeb/0x2a0 [qla2xxx]

Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: NJoe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When pci_enable_device() or pci_enable_device_mem() fail in
qla2x00_probe_one() we bail out but do a call to
pci_disable_device(). This causes the dev_WARN_ON() in
pci_disable_device() to trigger, as the device wasn't enabled
previously.

So instead of taking the 'probe_out' error path we can directly return
*iff* one of the pci_enable_device() calls fails.

Additionally rename the 'probe_out' goto label's name to the more
descriptive 'disable_device'.
Signed-off-by: NJohannes Thumshirn <jthumshirn@suse.de>
Fixes: e315cd28 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring")
Cc: <stable@vger.kernel.org>
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NGiridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There are several local or function parameter pointers that are being
assigned NULL after a kfree where and these have no effect and hence can
be removed.

Fixes various cppcheck warnings:

"Assignment of function parameter has no effect outside the
function. Did you forget dereferencing it"
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add fix to read correct register value for ISP82xx, during check for
register disconnect.ISP82xx has different base register.

Fixes: a465537a ("qla2xxx: Disable the adapter and skip error recovery in case of register disconnect")
Signed-off-by: NSawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Current driver wait for FW to be in the ready state before
processing in-coming commands. For Arbitrated Loop or
Point-to- Point (not switch), FW Ready state can take a while.
FW will transition to ready state after all Nports have been
logged in. In the mean time, certain initiators have completed
the login and starts IO. Driver needs to start processing all
queues if FW is already started.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

For target mode, when new scsi command arrive, driver first performs
a look up of the SCSI Host. The current look up method is based on
the ALPA portion of the NPort ID. For Cisco switch, the ALPA can
not be used as the index. Instead, the new search method is based
on the full value of the Nport_ID via btree lib.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Cc: <stable@vger.kernel.org>
Signed-off-by: NJoe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

After a Qlogic card breaks when initializing (test case), the system can
crash in qla2xxx_eh_abort if processing anything but a scsi command type
srb.

Fixes: 1535aa75 ("scsi: qla2xxx: fix invalid DMA access after command aborts in PCI device remove")
Signed-off-by: NBill Kuzeja <william.kuzeja@stratus.com>
Acked-By: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Target mode initialization was not calculating response queue values
correctly resulting into one less MSI-X vector.

[mkp: fixed Fixes: hash]

Cc: <stable@vger.kernel.org>
Fixes: 093df737 ("scsi: qla2xxx: Fix Target mode handling with Multiqueue changes.")
Signed-off-by: NMichael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch cleaned up queue configuration code, such that once
initialized, we should not touch msix_count value.  This will prevent
incorrect numbers of MSI-X vectors requested while performing target
mode configuration.

[mkp: fixed Fixes: hash]

Cc: <stable@vger.kernel.org>
Fixes: d7459527 ("scsi: qla2xxx: Add multiple queue pair functionality.")
Signed-off-by: NMichael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch does not change any functionality but avoids that sparse
complains about using variable-length arrays.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Acked-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Cc: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch simplifies SRB structure usage in driver.

- Simplify sp->done() and sp->free() interfaces.
- Remove sp->fcport->vha to use vha pointer from sp.
- Use sp->vha context in qla2x00_rel_sp().
Signed-off-by: NJoe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Current code blindly does State Change Registration when
the link is up. Move SCR behind fabric scan, so that arbitrated
loop scan would not get erroneous error message.

Some of the other improvements are as follows

- Add session deletion for TPRLO and send acknowledgment for TPRLO.
- Enable FW option to move ABTS, RIDA & PUREX from RSPQ to ATIOQ.
- Save NPort ID early in link init.
- Move ABTS & RIDA to ATIOQ helps in keeping command ordering and
  link up sequence ordering.
- Save Nport ID and update VP map so that SCSI CMD/ATIO won't be dropped.
- fcport alloc does the initializes memory to zero. Remove memset to
  zero since It might corrupt link list.
- Turn off Registration for State Change MB in loop mode.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>