Make sure we set the bias level for all DAPM contexts when
changing level.
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Codec shutdown performs a DAPM power sequence that might cause conflicts
and/or race conditions if another stream power event is running simultaneously.
Use card's dapm mutex to protect any potential race condition between them.
Signed-off-by: NMisael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

dapm_set_path_status() sets connect incorrectly in the case max > 1 with invert.
In that case, the raw disconnect value should be max, which corresponds to the
userspace value 0.

This use case currently does not appear upstream, but it could break
SOC_DAPM_SINGLE() or SOC_DAPM_SINGLE_TLV() elsewhere or in the future.

This patch completes commit 3a9abe8.

Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <alsa-devel@alsa-project.org>
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The mioa701 board code is converted to the snd_soc_register_card()
and snd_soc_unregister_card() APIs.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

In sound/soc/codecs/tlv320aic3x.c

        data = snd_soc_read(codec, AIC3X_PLL_PROGA_REG);
        snd_soc_write(codec, AIC3X_PLL_PROGA_REG,
                      data | (pll_p << PLLP_SHIFT));

In the above code, pll-p value is OR'ed with previous value without
clearing it. Bug is not seen if pll-p value doesn't change across
Sampling frequency.

However on some platforms (like AM335x EVM-SK), pll-p may have different
values across different sampling frequencies. In such case, above code
configures the pll with a wrong value.
Because of this bug, when a audio stream is played with pll value
different from previous stream, audio is heard as differently(like its
stretched).
Signed-off-by: NHebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

Without this very high BCLKs will be configured incorrectly.
Reported-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

The recent fix for power-map controls (commit b0791dda) caused
regressions on some other HP laptops.  They have fixed pins but these
pins are exposed as jack-detectable.  Thus the driver tries to control
the power-map dynamically per jack detection where it never gets on.

This patch adds the check of connection and it assumes the no jack
detection is available for fixed pins no matter what pin capability
says.

BugLink: http://bugs.launchpad.net/bugs/1013183Reported-by: NLuis Henriques <luis.henriques@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Better to clean up the caches for avoiding inconsistent codec state
after the reconfiguration.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some caches aren't released properly at module unloading time.

Cc: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When moved to the helper code, forgot to release the verb arrays.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This chip looks very similar to ALC269 and ALC27* variants. The bug reporter
has verified that sound was working after this patch had been applied.

Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/1017017Tested-by: NRichard Crossley <richardcrossley@o2.co.uk>
Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

I simply forgot to remove this entry although all Realtek quirks have
been dropped.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

It seems that the code duplication was added at a merge operation.
Signed-off-by: NJaroslav Kysela <perex@perex.cz>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Reported-by: NJohn McFarland <mcfarljm@gmail.com>
Tested-by: NJohn McFarland <mcfarljm@gmail.com>
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The Lenovo Ideapad S205 has an internal mic where the right channel
is phase inverted.

BugLink: https://bugs.launchpad.net/bugs/884652Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The codec ALC272X is a special codec for some Dell machines, and its
detection got broken in the recent kernel because SSID check (required
by ALC272X check) was moved to the later point.  Now we need to move
this codec check to the right place, too.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This webcam works mostly ok, exept with skype.
Skype sends lots of ctrl messages to dynamically ajust
record level. If for some reasons it pokes some error
every thing goes broken:
- first pulseaudio blocks sound for all apps
- then video is reseted
- then skype freez

dmesg has lots of messages like:
cannot set freq 16000 to ep 0x86"

Setting ignore_ctl_error=1 fixes this problem.
Signed-off-by: NOleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

if this cam is pluged in, pulse audio can't initiate capture
device.
dmesg has lots of messages like:
"cannot set freq 16000 to ep 0x86"

Setting ignore_ctl_error=1 fixes this problem.
Signed-off-by: NOleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NDaniel Mack <zonque@gmail.com>
Cc: Torsten Schenk <torsten.schenk@zoho.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This addresses an issue encountered when a pcm is opened while
transitioning to low power state (codec->power_on == 1 &&
codec->power_transition == -1).  Add snd_pcm_power_up_d3wait to
hda_codec.  This function is used to power up from azx_open as opposed
to snd_hda_power_up used from codec_exec_verb. When powering up from
azx_open, wait for pending power downs to complete, avoiding the power
up continuing in parallel with the power down on the work queue.

The specific issue seen was with the CS4210 codec, it powers off the ADC
and DAC nid in its suspend handler.  If it is re-opened before the
~100ms power down process completes, the ADC and DAC nid are initialized
while powered down and audio is lost until another suspend/resume cycle.
Signed-off-by: NDylan Reid <dgreid@chromium.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix a bogus sanity check for sync pipe in pcm.c. This flaw was
introduced during the streaming logic refactorization.

While at it, improve the error messages that are generated in such cases.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Reported-and-tested-by: <ben@b1c1l1.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ASoC: Updates for 3.5

All driver specific and fairly small.  The pxa-ssp changes are larger
than I'd like but they're build failures and are pretty clear to
inspection.

During the split to the auto-parser helper functions, the actual call
of init verbs was lost.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43366Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Pin 0x1b was connected to the front panel connector, which according to
the HDA standard should contain a mic and a headphone. In this case,
the headphone was listed as "line out" by BIOS.

Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/993162Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

as the start can be called after stop again, we need to reset state
Signed-off-by: NNamarta Kohli <namartax.kohli@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

during pause the core should maintain the status-quo on the device and pointers
and not wake up. If app needs it should call DROP explcitly.
Signed-off-by: NNamarta Kohli <namartax.kohli@intel.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

If mic detect is left enabled and the WM8903 detects a status change,
the WM8903 driver will make a callback against the free()d jack, which
will cause a crash.

This problem can be triggered by fully initializing an audio card, then
removing and re-inserting the machine driver module.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The PCI ID entries of Creative SoundCore3D HD-audio controllers should
be before the wildcard for vendor = Creative.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Otherwise we might try to write to a powered off device.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If we don't have control over the LDO but do have control over the other
regulators then we may end up trying to write to a powered off device.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We're using demv_regulator_bulk_get() so don't need to manually free and
this is in the CODEC driver not the I2C driver anyway.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We should be using the regmap API consistently for all the cache only
configuration and we should be going cache only before we power down
the supplies.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We no longer have a flat ASoC cache so can't peer directly into the array
any more but should instead use the register I/O functions to update the
cache.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org (v3.4)

pxa-ssp.c uses API like cpu_is_pxa3xx(), cpu_is_pxa2xx(), which is
defined under arch-pxa architecture, and drivers under mach-mmp
can't find it. so just use ssp->type to replace that API.
Signed-off-by: NQiao Zhou <zhouqiao@marvell.com>
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

add pxa910-ssp into ssp_id_table, and fix pxa-ssp compiling issue
under mach-mmp architect.
Signed-off-by: NQiao Zhou <zhouqiao@marvell.com>
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The audio clients have to be disabled before disabling the VGA and
switching.  Similarly, enabling the audio client should be done at
last.  Otherwise the audio-side operation stalls, eventually leading
to Oops or lockups.
Tested-by: NJörg-Volker Peetz <jvpeetz@web.de>
Acked-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When VGA_SWITCHEROO support is enabled hda_intel initialises the HDMI
audio device on the current VGA device.  When it's not enabled it only
initialises the HDMI device on the default VGA adaptor, this means
secondary cards get no audio support which is very unhelpful for
multi-seat!

With this patch, when SUPPORT_VGA_SWITCHEROO is disabled hda_intel
initialises all HDMI audio devices, not just the default VGA.

[minor optimizations by tiwai]
Signed-off-by: NSteven Newbury <steve@snewbury.org.uk>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix a typo that is built only when CONFIG_VGA_SWITCHEROO=n.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When VGA-switcheroo is built in but unused on systems with multiple
graphics cards, the initializations of non-default graphics cards are
skipped and never enabled (because the switcheroo is activated only
when the controller supports).  The current behavior is for avoiding
the system lockup by accessing the disabled GPU, but due to the recent
change in VGA-switcheroo, it determines the state simply by checking
with the default VGA device.  This is the culprit.

Now with the new vga_switcheroo_get_client_state(), we can know the
initial state of the bound GPU, thus can determine the initial audio
client state more correctly.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>