Move bus operations to its own file for the sake of clarity. Also
delegate sysfs attributes to bus handlers in preparation for other
more exotic types.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

ENE has a very weird design where an SDHCI device (0805) is presented
on the PCI bus, but that device is non-functional, and the real device
is hidden as a more generic device.
Signed-off-by: NMilko Krachounov <milko@3mhz.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Some hosts cannot do scatter/gather in hardware. Since not doing sg
is such a big performance hit, we (optionally) bounce the requests
to a simple linear buffer that we hand over to the driver.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Somehow the code to read the read-only switch of SD cards got lost
in the reorganisation.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Ignoring OMAP_MMC_STAT_CARD_ERR, treating it as if the command
completed correctly.
Signed-off-by: NRagner Magalhaes <ragner.magalhaes@indt.org.br>
Signed-off-by: NCarlos Eduardo Aguiar <carlos.aguiar@indt.org.br>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Make sure we don't call the switch function on cards too old to
support it. They should just ignore it, but some have been reported
to lock up instead.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Fix a broken if clause which was causing SD cards to go into
4-bit mode even if the host did not support it.

(Reported by David Brownell and Marc Pignat)
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Fix compilation error by removing command decoding from at91_mci.c driver.
Decoding commands in the host driver is the wrong way.
Signed-off-by: NMarc Pignat <marc.pignat@hevs.ch>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Remove dead code and unused structs from the block driver.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

... and make it depend on the response flag instead of the command type.
Signed-off-by: NNicolas Pitre <npitre@mvista.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The MMC block devices now have an assigned major. Make sure
we actually use it.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

When the device hits certain memory boundaries, it signals an
interrupt and expects to be serviced. We don't need the feature
but we need to make sure the device doesn't stall.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This patch has changed command types check from data flags.

MMC_STOP_TRANSMISSION is never passed to au1xmmc_send_command().
SEND_STOP() is used for MMC_STOP_TRANSMISSION.
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Add "depends on HAS_IOMEM" to a number of menus to make them
disappear for s390 which does not have I/O memory.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

As mmc_detect_change() can be called from irq context, using
claim (which can sleep) is inherently unsafe. Use the host
spinlock instead, which also is faster.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: NJan Engelhardt <jengelh@gmx.de>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Socket power must be fully controlled by adapter driver. This also prevents
unnecessary power-off of the socket when media driver is unloaded, yet
media remains in the socket.
Signed-off-by: NAlex Dubov <oakad@yahoo.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Move divisor calculation into a separate function and re-arrange the
init order to make MMC_POWER_ON work.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

As discussed earlier on LKML:

http://lkml.org/lkml/2006/5/4/44Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This patch add a missing '\n' at the end of the 'cover is open' string
in mmc_omap_switch_handler().
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

This patch makes the needlessly global tifm_sd_set_dma_data() static.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Remove card states that no longer make any sense.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Since many have the system root on MMC/SD we must allow some foot
shooting when it comes to resume.

We cannot detect if a card is removed and reinserted during suspend,
so the safe approach would be to assume it was, avoiding potential
filesystem corruption. This will of course not work if you cannot
release the card before suspend.

This commit adds a compile time option that makes the MMC layer
assume the card wasn't touched if it is redetected upon resume.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Separate the reading and decoding of the EXT_CSD register with the
actions taken on it.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Break apart the SD switch function into one that reads the capabilities
and one that acts on them.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Fix handling of low voltage MMC cards.

The latest MMC and SD specs both agree that support for
low-voltage operations is indicated by bit 7 in the OCR.
The MMC spec states that the low voltage range is
1.65-1.95V while the SD spec leaves the actual voltage
range undefined - meaning that there is still no such
thing as a low voltage SD card.

However, an old Sandisk spec implied that bits 7.0
represented voltages below 2.0V in 1V or 0.5V increments,
and the code was accordingly written with that expectation.

This confusion meant that host drivers attempting to support
the typical low voltage (1.8V) would set the wrong bits in
the host OCR mask (usually bits 5 and/or 6) resulting in the
the low voltage mode never being used.

This change corrects the low voltage range and adds sanity
checks on the reserved bits (0-6) and for SD cards that
claim to support low-voltage operations.
Signed-off-by: NPhilip Langdale <philipl@overt.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Consolidate the list of available voltages.

Up until now, a separate set of defines has been
used for host->vdd than that used for the OCR
voltage mask values. Having two sets of defines
allows them to get out of sync and the current
sets are already inconsistent with one claiming
to describe ranges and the other specific voltages.

Only the SDHCI driver uses the host->vdd defines and
it is easily fixed to use the OCR defines.
Signed-off-by: NPhilip Langdale <philipl@overt.org>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Delegate protocol handling to "bus handlers". This allows the core to
just handle the task of arbitrating the bus. Initialisation and
pampering of cards is now done by the different bus handlers.

This design also allows MMC and SD (and later SDIO) to be more cleanly
separated, allowing easier maintenance.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Move the check for supported data opcodes to the beginning of the
request function to avoid wedging the card.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Move protocol operations and definitions into their own files
in an effort to separate protocol handling and bus
arbitration more clearly.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Create a "core" subdirectory to house the central bus handling
functions.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The classic MMC bus was defined as multi card bus
system, which is reflected in the design in the MMC
layer.

When SD showed up, the bus topology was abandoned
and a star topology (one card per host) was mandated.
MMC version 4 has followed this, officially deprecating
the bus topology.

As we do not have any known users of the bus
topology we can remove support for it. This will
simplify the code and rectify some incorrect
assumptions in the newer additions.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Suspending MMC/SD cards (versus removing and readding them) is an
inherently unsafe operation and has even been broken for some time.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Make sure we don't deadlock when removing a suspended block
queue, something that might happen if the card is removed during
suspend.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Make sure we kill of any pending detection runs when the host
is removed instead of when it is freed. Also add some debugging
to make sure the driver doesn't queue up more detection after it
has removed the host.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Clean up the drivers/mmc directory by moving card and host drivers
into subdirectories.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The mmc block queue functions are tailored for the mmc_block
driver, so move those functions into that module.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

The "present" state indicates that the card is a registered device, so
it is more clear to put it together with the actual registration.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>