Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 161
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 18 6月, 2014 2 次提交
    • B
      PCI: pciehp: Compute timeout from hotplug command start time · 40b96083
      由 Bjorn Helgaas 提交于 
      If we issue a hotplug command, go do something else, then come back and
wait for the command to complete, we don't have to wait the whole timeout
period, because some of it elapsed while we were doing something else.

Keep track of the time we issued the command, and wait only until the
timeout period from that point has elapsed.

For controllers with errata like Intel CF118, we previously timed out
before issuing the second hotplug command:

  At time T1 (during boot):
    - Write DLLSCE, ABPE, PDCE, etc. to Slot Control
  At time T2 (hotplug event):
    - Wait for command completion (CC) in Slot Status
    - Timeout at T2 + 1 second because CC is never set in Slot Status
    - Write PCC, PIC, etc. to Slot Control

With this change, we wait until T1 + 1 second instead of T2 + 1 second.
If the hotplug event is more than 1 second after the boot-time
initialization, we won't wait for the timeout at all.

We still emit a "Timeout on hotplug command" message if it timed out; we
should see this on the first hotplug event on every controller with this
erratum, as well as on real errors on controllers without the erratum.

Link: http://www.intel.com/content/www/us/en/processors/xeon/xeon-e7-v2-spec-update.html
Tested-by: Rajat Jain <rajatxjain@gmail.com>	(IDT 807a controller)
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NYinghai Lu <yinghai@kernel.org>
      40b96083
    • B
      PCI: pciehp: Wait for hotplug command completion lazily · 3461a068
      由 Bjorn Helgaas 提交于 
      Previously we issued a hotplug command and waited for it to complete.  But
there's no need to wait until we're ready to issue the *next* command.  The
next command will probably be much later, so the first one may have already
completed and we may not have to actually wait at all.

Because of hardware errata, some controllers generate command completion
events for some commands but not others.  In the case of Intel CF118 (see
spec update reference), the controller indicates command completion only
for Slot Control writes that change the value of the following bits:

  Power Controller Control
  Power Indicator Control
  Attention Indicator Control
  Electromechanical Interlock Control

Changes to other bits, e.g., the interrupt enable bits, do not cause the
Command Completed bit to be set.  Controllers from AMD and Nvidia are
reported to have similar errata.

These errata cause timeouts when pcie_enable_notification() enables
interrupts.  Previously that timeout occurred at boot-time.  With this
change, the timeout occurs later, when we change the state of the slot
power, indicators, or interlock.  This speeds up boot but causes a timeout
at the first hotplug event on the slot.  Subsequent events don't timeout
because only the first (boot-time) hotplug command updates Slot Control
without touching the power/indicator/interlock controls.

Link: http://www.intel.com/content/www/us/en/processors/xeon/xeon-e7-v2-spec-update.html
Tested-by: Rajat Jain <rajatxjain@gmail.com>	(IDT 807a controller)
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NYinghai Lu <yinghai@kernel.org>
      3461a068
  3. 17 6月, 2014 2 次提交
  5. 12 6月, 2014 3 次提交
  7. 11 6月, 2014 3 次提交
  9. 10 6月, 2014 1 次提交
  11. 31 5月, 2014 6 次提交
  13. 30 5月, 2014 3 次提交
  15. 29 5月, 2014 7 次提交
  17. 28 5月, 2014 13 次提交