- 18 10月, 2016 5 次提交
-
-
由 Tobias Klauser 提交于
args.u.name_type is of type unsigned int and is always >= 0. This fixes the following GCC warning: net/8021q/vlan.c: In function ‘vlan_ioctl_handler’: net/8021q/vlan.c:574:14: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits] Signed-off-by: NTobias Klauser <tklauser@distanz.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wei Yongjun 提交于
Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: 39339616 ("fsl/fman: Add FMan MAC driver") Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jakub Kicinski 提交于
Check is for max_mtu but message reports min_mtu. Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wei Yongjun 提交于
Fix to return error code -ENODEV from the of_phy_connect() error handling case instead of 0, as done elsewhere in this function. Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com> Acked-by: NMans Rullgard <mans@mansr.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arnd Bergmann 提交于
phys_addr_t may be wider than a pointer and has to be printed using the special %pap format string, as pointed out by this new warning. arch/x86/include/../../../drivers/net/fjes/fjes_trace.h: In function ‘trace_raw_output_fjes_hw_start_debug_req’: arch/x86/include/../../../drivers/net/fjes/fjes_trace.h:212:563: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast] Note that this has to pass the address by reference instead of casting it to a different type. Fixes: b6ba737d ("fjes: ethtool -w and -W support for fjes driver") Signed-off-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 10月, 2016 10 次提交
-
-
由 David S. Miller 提交于
Andrew Lunn says: ==================== Interrupt support for mv88e6xxx This patchset add interrupt controller support to the MV88E6xxx. This allows access to the interrupts the internal PHY generate. These interrupts can then be associated to a PHY device in the device tree and used by the PHY lib, rather than polling. Since interrupt handling needs to make MDIO bus accesses, threaded interrupts are used. The phylib needs to request the PHY interrupt using the threaded IRQ API. This in term allows some simplification to the code, in that the phylib interrupt handler can directly call phy_change(), rather than use a work queue. The work queue is however retained for the phy_mac_interrupt() call, which can be called in hard interrupt context. Since RFC v1: Keep phy_mac_interrupt() callable in hard IRQ context. The fix to trigger the phy state machine transitions on interrupts has already been submitted, so is dropped from here. Added back shared interrupts support. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
The Switches use GPIO lines to indicate interrupts from two of the switches. With these interrupts in place, we can make use of the interrupt controllers within the switch to indicate when the internal PHYs generate an interrupt. Use standard PHY properties to do this. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
Using the fixed name "phy_interrupt" is not very informative in /proc/interrupts when there are a lot of phys, e.g. a device with an Ethernet switch. So when requesting the interrupt, use the name of the phy. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Acked-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
The PHY interrupts are now handled in a threaded interrupt handler, which can sleep. The work queue is no longer needed, phy_change() can be called directly. phy_mac_interrupt() still needs to be safe to call in interrupt context, so keep the work queue, and use a helper to call phy_change(). Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
The interrupt lines from PHYs maybe connected to I2C bus expanders, or from switches on MDIO busses. Such interrupts are sourced from devices which sleep, so use threaded interrupts. Threaded interrupts require that the interrupt requester also uses the threaded API. Change the phylib to use the threaded API, which is backwards compatible with none-threaded IRQs. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andrew Lunn 提交于
The switch can have up to two interrupt controllers. One of these contains the interrupts from the integrated PHYs, so is useful to export. The Marvell PHY driver can then be used in interrupt mode, rather than polling, speeding up PHY handling and reducing load on the MDIO bus. Signed-off-by: NAndrew Lunn <andrew@lunn.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
rds_conn_path_error already prefixes "RDS:" to the output. Signed-off-by: NJoe Perches <joe@perches.com> Acked-by: NSowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Joe Perches 提交于
This macro's last use was removed in commit d769ef81 ("RDS: Update rds_conn_shutdown to work with rds_conn_path") so make the macro and the __rds_conn_error function definition and declaration disappear. Signed-off-by: NJoe Perches <joe@perches.com> Acked-by: NSowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tobias Klauser 提交于
There is no need to call ether_setup after alloc_ethdev since it was already called there. Signed-off-by: NTobias Klauser <tklauser@distanz.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tom Herbert 提交于
If the gateway is set on an ILA route we don't need to bother with using the destination cache in the ILA route. Translation does not change the routing in this case so we can stick with orig_output in the lwstate output function. Tested: Ran netperf with and without gateway for LWT route. Signed-off-by: NTom Herbert <tom@herbertland.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 16 10月, 2016 4 次提交
-
-
由 Julia Lawall 提交于
This l3mdev_ops structure is only stored in the l3mdev_ops field of a net_device structure. This field is declared const, so the l3mdev_ops structure can be declared as const also. Additionally drop the __read_mostly annotation. The semantic patch that adds const is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r disable optional_qualifier@ identifier i; position p; @@ static struct l3mdev_ops i@p = { ... }; @ok@ identifier r.i; struct net_device *e; position p; @@ e->l3mdev_ops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct l3mdev_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct l3mdev_ops i = { ... }; // </smpl> The effect on the layout of the .o file is shown by the following output of the size command, first before then after the transformation: text data bss dec hex filename 7364 466 52 7882 1eca drivers/net/ipvlan/ipvlan_main.o 7412 434 52 7898 1eda drivers/net/ipvlan/ipvlan_main.o Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Tom Herbert says: ==================== ila: Cache a route in ILA lwt structure Add a dst_cache to ila_lwt structure. This holds a cached route for the translated address. In ila_output we now perform a route lookup after translation and if possible (destination in original route is full 128 bits) we set the dst_cache. Subsequent calls to ila_output can then use the cache to avoid the route lookup. This eliminates the need to set the gateway on ILA routes as previously was being done. Now we can do somthing like: ./ip route add 3333::2000:0:0:2/128 encap ila 2222:0:0:2 \ csum-mode neutral-map dev eth0 ## No via needed! Also, add destroy_state to lwt ops. We need this do destroy the dst_cache. - v2 - Fixed comparisons to fc_dst_len to make comparison against number of bits in data structure not bytes. - Move destroy_state under build_state (requested by Jiri) - Other minor cleanup Tested: Running 200 TCP_RR streams: Baseline, no ILA 1730716 tps 102/170/313 50/90/99% latencies 88.11 CPU utilization Using ILA in both directions 1680428 tps 105/176/325 50/90/99% latencies 88.16 CPU utilization ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tom Herbert 提交于
Add a dst_cache to ila_lwt structure. This holds a cached route for the translated address. In ila_output we now perform a route lookup after translation and if possible (destination in original route is full 128 bits) we set the dst_cache. Subsequent calls to ila_output can then use the cache to avoid the route lookup. This eliminates the need to set the gateway on ILA routes as previously was being done. Now we can do something like: ./ip route add 3333::2000:0:0:2/128 encap ila 2222:0:0:2 \ csum-mode neutral-map dev eth0 ## No via needed! Signed-off-by: NTom Herbert <tom@herbertland.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tom Herbert 提交于
Users of lwt tunnels may set up some secondary state in build_state function. Add a corresponding destroy_state function to allow users to clean up state. This destroy state function is called from lwstate_free. Also, we now free lwstate using kfree_rcu so user can assume structure is not freed before rcu. Acked-by: NRoopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: NTom Herbert <tom@herbertland.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 15 10月, 2016 7 次提交
-
-
由 David S. Miller 提交于
Taku Izumi says: ==================== FUJITSU Extended Socket driver version 1.2 This patchset updates FUJITSU Extended Socket network driver into version 1.2. This includes the following enhancements: - ethtool -d support - ethtool -S enhancement - ethtool -w/-W support - Add some debugging feature (tracepoints etc) v1 -> v2: - Use u64 instead of phys_addr_t as TP_STRUCT__entry - Use ethtool facility to achieve debug mode instead of using debugfs ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Taku Izumi 提交于
Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Taku Izumi 提交于
This patch adds debugfs entry to show EP status information. You can get each EP's status information like the following: # cat /sys/kernel/debug/fjes/fjes.0/status EPID STATUS SAME_ZONE CONNECTED ep0 shared Y Y ep1 - - - ep2 unshared N N ep3 unshared N N ep4 unshared N N ep5 unshared N N ep6 unshared N N ep7 unshared N N Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Taku Izumi 提交于
This patch adds implementation of supporting ethtool -w and -W for fjes driver. You can enable and disable firmware debug mode by using ethtool -W, and also retrieve firmware activity information by using ethtool -w. This is useful for debugging. Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Taku Izumi 提交于
This patch adds tracepoints in fjes driver. This is useful for debugging purpose. Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Taku Izumi 提交于
This patch enhances ethtool -S for fjes driver so that EP related statistics can be retrieved. The following statistics can be displayed via ethtool -S: ep%d_com_regist_buf_exec ep%d_com_unregist_buf_exec ep%d_send_intr_rx ep%d_send_intr_unshare ep%d_send_intr_zoneupdate ep%d_recv_intr_rx ep%d_recv_intr_unshare ep%d_recv_intr_stop ep%d_recv_intr_zoneupdate ep%d_tx_buffer_full ep%d_tx_dropped_not_shared ep%d_tx_dropped_ver_mismatch ep%d_tx_dropped_buf_size_mismatch ep%d_tx_dropped_vlanid_mismatch Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Taku Izumi 提交于
This patch adds implementation of supporting ethtool -d for fjes driver. By using ethtool -d, you can get registers dump of Exetnded socket device. # ethtool -d es0 Offset Values ------ ------ 0x0000: 01 00 00 00 08 00 00 00 00 00 00 00 00 00 00 00 0x0010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0020: 02 00 00 80 02 00 00 80 64 a6 58 08 07 00 00 00 0x0030: 00 00 00 00 28 80 00 00 00 00 f9 e3 06 00 00 00 0x0040: 00 00 00 00 18 00 00 00 80 a4 58 08 07 00 00 00 0x0050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0x0080: 00 00 00 00 00 00 e0 7f 00 00 01 00 00 00 01 00 0x0090: 00 00 00 00 Signed-off-by: NTaku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 10月, 2016 14 次提交
-
-
由 David S. Miller 提交于
Manish Chopra says: ==================== qed*: driver updates There are several new additions in this series; Most are connected to either Tx offloading or Rx classifications [either fastpath changes or supporting configuration]. In addition, there's a single IOV enhancement. Please consider applying this series to `net-next'. V2->V3: Fixes below kbuild warning call to '__compiletime_assert_60' declared with attribute error: Need native word sized stores/loads for atomicity. V1->V2: Added a fix for the race in ramrod handling pointed by Eric Dumazet [patch 7]. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Manish Chopra 提交于
While handling SPQ ramrod completion, there is a possible race where driver might not read updated fw return code based on ramrod completion done. This patch ensures that fw return code is written first and then completion done flag is updated using appropriate memory barriers. Signed-off-by: NManish Chopra <manish.chopra@caviumnetworks.com> Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Malicious VFs might be caught in several different methods: - Misusing their bar permission and being blocked by hardware. - Misusing their fastpath logic and being blocked by firmware. - Misusing their interaction with their PF via hw-channel, and being blocked by PF driver. On the first two items, firmware would indicate to driver that the VF is to be considered malicious, but would sometime still allow the VF to communicate with the PF [depending on the exact nature of the malicious activity done by the VF]. The current existing logic on the PF side lacks handling of such events, and might allow the PF to perform some incorrect configuration on behalf of a VF that was previously indicated as malicious. The new scheme is simple - Once the PF determines a VF is malicious it would: a. Ignore any further requests on behalf of the VF-driver. b. Prevent any configurations initiated by the hyperuser for the malicious VF, as firmware isn't willing to serve such. The malicious indication would be cleared upon the VF flr, after which it would become usable once again. Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Whenever a ramrod is being sent for some device configuration, the driver is going to sleep at least 5ms between each iteration of polling on the completion of the ramrod. However, in almost every configuration scenario the firmware would be able to comply and complete the ramrod in a manner of several usecs. This is especially important in cases where there might be a lot of sequential configurations applying to the hardware [e.g., RoCE], in which case the existing scheme might cause some visible user delays. This patch changes the completion scheme - instead of immediately starting to sleep for a 'long' period, allow the device to quickly poll on the first iteration after a couple of usecs. Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Apparently qede fails to set IFF_UNICAST_FLT, and as a result is not actually performing unicast MAC filtering. While we're at it - relax a hard-coded limitation that limits each interface into using at most 15 unicast MAC addresses before turning promiscuous. Instead utilize the HW resources to their limit. Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Manish Chopra 提交于
Due to hardware limitation, when transmitting a geneve-encapsulated packet with more than 32 bytes worth of geneve options the hardware would not be able to crack the packet and consider it a regular UDP packet. This implements the ndo_features_check() in qede in order to prevent GSO on said transmitted packets. Signed-off-by: NManish Chopra <manish.chopra@caviumnetworks.com> Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Manish Chopra 提交于
This patch adds GSO support for GRE and UDP tunnels where outer checksums are enabled. Signed-off-by: NManish Chopra <manish.chopra@caviumnetworks.com> Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Some hypervisors can support MAC hints to their VFs. Even though we don't have such a hypervisor API in linux, we add sufficient logic for the VF to be able to receive such hints and set the mac accordingly - as long as the VF has not been set with a MAC already. Signed-off-by: NYuval Mintz <Yuval.Mintz@caviumnetworks.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Shmulik Ladkani says: ==================== act_mirred: Ingress actions support This patch series implements action mirred 'ingress' actions TCA_INGRESS_REDIR and TCA_INGRESS_MIRROR. This allows attaching filters whose target is to hand matching skbs into the rx processing of a specified device. v4: in 4/4, check ret code of netif_receive_skb, as suggested by Cong Wang v3: in 4/4, addressed non coherency due to reading m->tcfm_eaction multiple times, as spotted by Eric Dumazet v2: in 1/4, declare tcfm_mac_header_xmit as bool instead of int ==================== Acked-by: NCong Wang <xiyou.wangcong@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shmulik Ladkani 提交于
Up until now, 'action mirred' supported only egress actions (either TCA_EGRESS_REDIR or TCA_EGRESS_MIRROR). This patch implements the corresponding ingress actions TCA_INGRESS_REDIR and TCA_INGRESS_MIRROR. This allows attaching filters whose target is to hand matching skbs into the rx processing of a specified device. Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Tested-by: NJamal Hadi Salim <jhs@mojatatu.com> Acked-by: NJamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shmulik Ladkani 提交于
These accessors are used in various drivers that support tc offloading, to detect properties of a given 'tc_action'. 'is_tcf_mirred_redirect' tests that the action is TCA_EGRESS_REDIR. 'is_tcf_mirred_mirror' tests that the action is TCA_EGRESS_MIRROR. As a prep towards supporting INGRESS redir/mirror, rename these predicates to reflect their true meaning: s/is_tcf_mirred_redirect/is_tcf_mirred_egress_redirect/ s/is_tcf_mirred_mirror/is_tcf_mirred_egress_mirror/ Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com> Cc: Hariprasad S <hariprasad@chelsio.com> Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Saeed Mahameed <saeedm@mellanox.com> Cc: Jiri Pirko <jiri@mellanox.com> Cc: Ido Schimmel <idosch@mellanox.com> Cc: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: NJamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shmulik Ladkani 提交于
Move detection logic that tests whether device expects skb data to point at mac_header upon xmit into a function. Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com> Acked-by: NJamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shmulik Ladkani 提交于
'tcfm_ok_push' specifies whether a mac_len sized push is needed upon egress to the target device (if action is performed at ingress). Rename it to 'tcfm_mac_header_xmit' as this is actually an attribute of the target device (and use a bool instead of int). This allows to decouple the attribute from the action to be taken. Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com> Acked-by: NJamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Allan W. Nielsen 提交于
Edge-Rate cleanup include the following: - Updated device tree bindings documentation for edge-rate - The edge-rate is now specified as a "slowdown", meaning that it is now being specified as positive values instead of negative (both documentation and implementation wise). - Only explicitly documented values for "vsc8531,vddmac" and "vsc8531,edge-slowdown" are accepted by the device driver. - Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed. - Read/validate devicetree settings in probe instead of init Signed-off-by: NAllan W. Nielsen <allan.nielsen@microsemi.com> Signed-off-by: NRaju Lakkaraju <raju.lakkaraju@microsemi.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-