T: Bus=01 Lev=02 Prnt=02 Port=03 Cnt=03 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f3 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=74DE2B344A7B
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NManoj Iyer <manoj.iyer@canonical.com>
Tested-by: NDennis Chua <dennis.chua@canonical.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

We should only perform a reset in hci_dev_do_close if the
HCI_QUIRK_NO_RESET flag is set (since in such a case a reset will not be
performed when initializing the device).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

There is an imbalance in the rfcomm_session_hold / rfcomm_session_put
operations which causes the following crash:

[  685.010159] BUG: unable to handle kernel paging request at 6b6b6b6b
[  685.010169] IP: [<c149d76d>] rfcomm_process_dlcs+0x1b/0x15e
[  685.010181] *pdpt = 000000002d665001 *pde = 0000000000000000
[  685.010191] Oops: 0000 [#1] PREEMPT SMP
[  685.010247]
[  685.010255] Pid: 947, comm: krfcommd Tainted: G         C  3.0.16-mid8-dirty #44
[  685.010266] EIP: 0060:[<c149d76d>] EFLAGS: 00010246 CPU: 1
[  685.010274] EIP is at rfcomm_process_dlcs+0x1b/0x15e
[  685.010281] EAX: e79f551c EBX: 6b6b6b6b ECX: 00000007 EDX: e79f40b4
[  685.010288] ESI: e79f4060 EDI: ed4e1f70 EBP: ed4e1f68 ESP: ed4e1f50
[  685.010295]  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[  685.010303] Process krfcommd (pid: 947, ti=ed4e0000 task=ed43e5e0 task.ti=ed4e0000)
[  685.010308] Stack:
[  685.010312]  ed4e1f68 c149eb53 e5925150 e79f4060 ed500000 ed4e1f70 ed4e1f80 c149ec10
[  685.010331]  00000000 ed43e5e0 00000000 ed4e1f90 ed4e1f9c c149ec87 0000bf54 00000000
[  685.010348]  00000000 ee03bf54 c149ec37 ed4e1fe4 c104fe01 00000000 00000000 00000000
[  685.010367] Call Trace:
[  685.010376]  [<c149eb53>] ? rfcomm_process_rx+0x6e/0x74
[  685.010387]  [<c149ec10>] rfcomm_process_sessions+0xb7/0xde
[  685.010398]  [<c149ec87>] rfcomm_run+0x50/0x6d
[  685.010409]  [<c149ec37>] ? rfcomm_process_sessions+0xde/0xde
[  685.010419]  [<c104fe01>] kthread+0x63/0x68
[  685.010431]  [<c104fd9e>] ? __init_kthread_worker+0x42/0x42
[  685.010442]  [<c14dae82>] kernel_thread_helper+0x6/0xd

This issue has been brought up earlier here:

https://lkml.org/lkml/2011/5/21/127

The issue appears to be the rfcomm_session_put in rfcomm_recv_ua. This
operation doesn't seem be to required as for the non-initiator case we
have the rfcomm_process_rx doing an explicit put and in the initiator
case the last dlc_unlink will drive the reference counter to 0.

There have been several attempts to fix these issue:

6c2718da Bluetooth: Do not call rfcomm_session_put() for RFCOMM UA on closed socket
683d949a Bluetooth: Never deallocate a session when some DLC points to it

but AFAICS they do not fix the issue just make it harder to reproduce.
Signed-off-by: NOctavian Purdila <octavian.purdila@intel.com>
Signed-off-by: NGopala Krishna Murala <gopala.krishna.murala@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

We don't need to use the _sync variant in hci_conn_hold and
hci_conn_put to cancel conn->disc_work delayed work. This way
we avoid potential deadlocks like this one reported by lockdep.

======================================================
[ INFO: possible circular locking dependency detected ]
3.2.0+ #1 Not tainted
-------------------------------------------------------
kworker/u:1/17 is trying to acquire lock:
 (&hdev->lock){+.+.+.}, at: [<ffffffffa0041155>] hci_conn_timeout+0x62/0x158 [bluetooth]

but task is already holding lock:
 ((&(&conn->disc_work)->work)){+.+...}, at: [<ffffffff81035751>] process_one_work+0x11a/0x2bf

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 ((&(&conn->disc_work)->work)){+.+...}:
       [<ffffffff81057444>] lock_acquire+0x8a/0xa7
       [<ffffffff81034ed1>] wait_on_work+0x3d/0xaa
       [<ffffffff81035b54>] __cancel_work_timer+0xac/0xef
       [<ffffffff81035ba4>] cancel_delayed_work_sync+0xd/0xf
       [<ffffffffa00554b0>] smp_chan_create+0xde/0xe6 [bluetooth]
       [<ffffffffa0056160>] smp_conn_security+0xa3/0x12d [bluetooth]
       [<ffffffffa0053640>] l2cap_connect_cfm+0x237/0x2e8 [bluetooth]
       [<ffffffffa004239c>] hci_proto_connect_cfm+0x2d/0x6f [bluetooth]
       [<ffffffffa0046ea5>] hci_event_packet+0x29d1/0x2d60 [bluetooth]
       [<ffffffffa003dde3>] hci_rx_work+0xd0/0x2e1 [bluetooth]
       [<ffffffff810357af>] process_one_work+0x178/0x2bf
       [<ffffffff81036178>] worker_thread+0xce/0x152
       [<ffffffff81039a03>] kthread+0x95/0x9d
       [<ffffffff812e7754>] kernel_thread_helper+0x4/0x10

-> #1 (slock-AF_BLUETOOTH-BTPROTO_L2CAP){+.+...}:
       [<ffffffff81057444>] lock_acquire+0x8a/0xa7
       [<ffffffff812e553a>] _raw_spin_lock_bh+0x36/0x6a
       [<ffffffff81244d56>] lock_sock_nested+0x24/0x7f
       [<ffffffffa004d96f>] lock_sock+0xb/0xd [bluetooth]
       [<ffffffffa0052906>] l2cap_chan_connect+0xa9/0x26f [bluetooth]
       [<ffffffffa00545f8>] l2cap_sock_connect+0xb3/0xff [bluetooth]
       [<ffffffff81243b48>] sys_connect+0x69/0x8a
       [<ffffffff812e6579>] system_call_fastpath+0x16/0x1b

-> #0 (&hdev->lock){+.+.+.}:
       [<ffffffff81056d06>] __lock_acquire+0xa80/0xd74
       [<ffffffff81057444>] lock_acquire+0x8a/0xa7
       [<ffffffff812e3870>] __mutex_lock_common+0x48/0x38e
       [<ffffffff812e3c75>] mutex_lock_nested+0x2a/0x31
       [<ffffffffa0041155>] hci_conn_timeout+0x62/0x158 [bluetooth]
       [<ffffffff810357af>] process_one_work+0x178/0x2bf
       [<ffffffff81036178>] worker_thread+0xce/0x152
       [<ffffffff81039a03>] kthread+0x95/0x9d
       [<ffffffff812e7754>] kernel_thread_helper+0x4/0x10

other info that might help us debug this:

Chain exists of:
  &hdev->lock --> slock-AF_BLUETOOTH-BTPROTO_L2CAP --> (&(&conn->disc_work)->work)

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock((&(&conn->disc_work)->work));
                               lock(slock-AF_BLUETOOTH-BTPROTO_L2CAP);
                               lock((&(&conn->disc_work)->work));
  lock(&hdev->lock);

 *** DEADLOCK ***

2 locks held by kworker/u:1/17:
 #0:  (hdev->name){.+.+.+}, at: [<ffffffff81035751>] process_one_work+0x11a/0x2bf
 #1:  ((&(&conn->disc_work)->work)){+.+...}, at: [<ffffffff81035751>] process_one_work+0x11a/0x2bf

stack backtrace:
Pid: 17, comm: kworker/u:1 Not tainted 3.2.0+ #1
Call Trace:
 [<ffffffff812e06c6>] print_circular_bug+0x1f8/0x209
 [<ffffffff81056d06>] __lock_acquire+0xa80/0xd74
 [<ffffffff81021ef2>] ? arch_local_irq_restore+0x6/0xd
 [<ffffffff81022bc7>] ? vprintk+0x3f9/0x41e
 [<ffffffff81057444>] lock_acquire+0x8a/0xa7
 [<ffffffffa0041155>] ? hci_conn_timeout+0x62/0x158 [bluetooth]
 [<ffffffff812e3870>] __mutex_lock_common+0x48/0x38e
 [<ffffffffa0041155>] ? hci_conn_timeout+0x62/0x158 [bluetooth]
 [<ffffffff81190fd6>] ? __dynamic_pr_debug+0x6d/0x6f
 [<ffffffffa0041155>] ? hci_conn_timeout+0x62/0x158 [bluetooth]
 [<ffffffff8105320f>] ? trace_hardirqs_off+0xd/0xf
 [<ffffffff812e3c75>] mutex_lock_nested+0x2a/0x31
 [<ffffffffa0041155>] hci_conn_timeout+0x62/0x158 [bluetooth]
 [<ffffffff810357af>] process_one_work+0x178/0x2bf
 [<ffffffff81035751>] ? process_one_work+0x11a/0x2bf
 [<ffffffff81055af3>] ? lock_acquired+0x1d0/0x1df
 [<ffffffffa00410f3>] ? hci_acl_disconn+0x65/0x65 [bluetooth]
 [<ffffffff81036178>] worker_thread+0xce/0x152
 [<ffffffff810407ed>] ? finish_task_switch+0x45/0xc5
 [<ffffffff810360aa>] ? manage_workers.isra.25+0x16a/0x16a
 [<ffffffff81039a03>] kthread+0x95/0x9d
 [<ffffffff812e7754>] kernel_thread_helper+0x4/0x10
 [<ffffffff812e5db4>] ? retint_restore_args+0x13/0x13
 [<ffffffff8103996e>] ? __init_kthread_worker+0x55/0x55
 [<ffffffff812e7750>] ? gs_change+0x13/0x13
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@openbossa.org>
Reviewed-by: NUlisses Furquim <ulisses@profusion.mobi>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Since bluetooth uses multiple protocols types, to avoid lockdep
warnings, we need to use different lockdep classes (one for each
protocol type).

This is already done in bt_sock_create but it misses a couple of cases
when new connections are created. This patch corrects that to fix the
following warning:

<4>[ 1864.732366] =======================================================
<4>[ 1864.733030] [ INFO: possible circular locking dependency detected ]
<4>[ 1864.733544] 3.0.16-mid3-00007-gc9a0f62 #3
<4>[ 1864.733883] -------------------------------------------------------
<4>[ 1864.734408] t.android.btclc/4204 is trying to acquire lock:
<4>[ 1864.734869]  (rfcomm_mutex){+.+.+.}, at: [<c14970ea>] rfcomm_dlc_close+0x15/0x30
<4>[ 1864.735541]
<4>[ 1864.735549] but task is already holding lock:
<4>[ 1864.736045]  (sk_lock-AF_BLUETOOTH){+.+.+.}, at: [<c1498bf7>] lock_sock+0xa/0xc
<4>[ 1864.736732]
<4>[ 1864.736740] which lock already depends on the new lock.
<4>[ 1864.736750]
<4>[ 1864.737428]
<4>[ 1864.737437] the existing dependency chain (in reverse order) is:
<4>[ 1864.738016]
<4>[ 1864.738023] -> #1 (sk_lock-AF_BLUETOOTH){+.+.+.}:
<4>[ 1864.738549]        [<c1062273>] lock_acquire+0x104/0x140
<4>[ 1864.738977]        [<c13d35c1>] lock_sock_nested+0x58/0x68
<4>[ 1864.739411]        [<c1493c33>] l2cap_sock_sendmsg+0x3e/0x76
<4>[ 1864.739858]        [<c13d06c3>] __sock_sendmsg+0x50/0x59
<4>[ 1864.740279]        [<c13d0ea2>] sock_sendmsg+0x94/0xa8
<4>[ 1864.740687]        [<c13d0ede>] kernel_sendmsg+0x28/0x37
<4>[ 1864.741106]        [<c14969ca>] rfcomm_send_frame+0x30/0x38
<4>[ 1864.741542]        [<c1496a2a>] rfcomm_send_ua+0x58/0x5a
<4>[ 1864.741959]        [<c1498447>] rfcomm_run+0x441/0xb52
<4>[ 1864.742365]        [<c104f095>] kthread+0x63/0x68
<4>[ 1864.742742]        [<c14d5182>] kernel_thread_helper+0x6/0xd
<4>[ 1864.743187]
<4>[ 1864.743193] -> #0 (rfcomm_mutex){+.+.+.}:
<4>[ 1864.743667]        [<c1061ada>] __lock_acquire+0x988/0xc00
<4>[ 1864.744100]        [<c1062273>] lock_acquire+0x104/0x140
<4>[ 1864.744519]        [<c14d2c70>] __mutex_lock_common+0x3b/0x33f
<4>[ 1864.744975]        [<c14d303e>] mutex_lock_nested+0x2d/0x36
<4>[ 1864.745412]        [<c14970ea>] rfcomm_dlc_close+0x15/0x30
<4>[ 1864.745842]        [<c14990d9>] __rfcomm_sock_close+0x5f/0x6b
<4>[ 1864.746288]        [<c1499114>] rfcomm_sock_shutdown+0x2f/0x62
<4>[ 1864.746737]        [<c13d275d>] sys_socketcall+0x1db/0x422
<4>[ 1864.747165]        [<c14d42f0>] syscall_call+0x7/0xb
Signed-off-by: NOctavian Purdila <octavian.purdila@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

queue_delayed_work() expects a relative time for when that work
should be scheduled.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@openbossa.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

After moving L2CAP timers to workqueues l2cap_set_timer expects timeout
value to be specified in jiffies but constants defined in miliseconds
are used. This makes timeouts unreliable when CONFIG_HZ is not set to
1000.

__set_chan_timer macro still uses jiffies as input to avoid multiple
conversions from/to jiffies for sk_sndtimeo value which is already
specified in jiffies.
Signed-off-by: NAndrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Ackec-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

sk_sndtime value should be specified in jiffies thus initial value
needs to be converted from miliseconds. Otherwise this timeout is
unreliable when CONFIG_HZ is not set to 1000.
Signed-off-by: NAndrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

As reported by Dan Carpenter this function causes a Sparse warning and
shouldn't be declared inline:

include/net/bluetooth/l2cap.h:837:30 error: marked inline, but without a
definition"
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>

[ 2096.384084] btusb_send_frame:684: hci0
[ 2096.384087] usb 3-1: BOGUS urb flags, 2 --> 0
[ 2096.384091] Bluetooth: hci0 urb ffff8801b61d3a80 submission failed (22)

According the documentation in usb_submit_urb() URB_ISO_ASAP
flag is only allowed for endpoints of type USB_ENDPOINT_XFER_ISOC.

This reverts commit b8aabfc9.
Signed-off-by: NDaniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Commit 33060542 fixed l2cap conn establishment for non-ssp remote
devices by not setting HCI_CONN_ENCRYPT_PEND every time conn security
is tested (which was always returning failure on any subsequent
security checks).

However, this broke l2cap conn establishment for ssp remote devices
when an ACL link was already established at SDP-level security. This
fix ensures that encryption must be pending whenever authentication
is also pending.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-by: NDaniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Fixes problem where caller would think routine succeeded when it failed
leading to divide by zero panic.
Signed-off-by: NSimon Graham <simon.graham@virtualcomputer.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

read_lock(&tpt_trig->trig.leddev_list_lock) is accessed via the path
ieee80211_open (->) ieee80211_do_open (->) ieee80211_mod_tpt_led_trig
(->) ieee80211_start_tpt_led_trig (->) tpt_trig_timer before initializing
it.
the intilization of this read/write lock happens via the path
ieee80211_led_init (->) led_trigger_register, but we are doing
'ieee80211_led_init'  after 'ieeee80211_if_add' where we
register netdev_ops.
so we access leddev_list_lock before initializing it and causes the
following bug in chrome laptops with AR928X cards with the following
script

while true
do
sudo modprobe -v ath9k
sleep 3
sudo modprobe -r ath9k
sleep 3
done

	BUG: rwlock bad magic on CPU#1, wpa_supplicant/358, f5b9eccc
	Pid: 358, comm: wpa_supplicant Not tainted 3.0.13 #1
	Call Trace:

	[<8137b9df>] rwlock_bug+0x3d/0x47
	[<81179830>] do_raw_read_lock+0x19/0x29
	[<8137f063>] _raw_read_lock+0xd/0xf
	[<f9081957>] tpt_trig_timer+0xc3/0x145 [mac80211]
	[<f9081f3a>] ieee80211_mod_tpt_led_trig+0x152/0x174 [mac80211]
	[<f9076a3f>] ieee80211_do_open+0x11e/0x42e [mac80211]
	[<f9075390>] ? ieee80211_check_concurrent_iface+0x26/0x13c [mac80211]
	[<f9076d97>] ieee80211_open+0x48/0x4c [mac80211]
	[<812dbed8>] __dev_open+0x82/0xab
	[<812dc0c9>] __dev_change_flags+0x9c/0x113
	[<812dc1ae>] dev_change_flags+0x18/0x44
	[<8132144f>] devinet_ioctl+0x243/0x51a
	[<81321ba9>] inet_ioctl+0x93/0xac
	[<812cc951>] sock_ioctl+0x1c6/0x1ea
	[<812cc78b>] ? might_fault+0x20/0x20
	[<810b1ebb>] do_vfs_ioctl+0x46e/0x4a2
	[<810a6ebb>] ? fget_light+0x2f/0x70
	[<812ce549>] ? sys_recvmsg+0x3e/0x48
	[<810b1f35>] sys_ioctl+0x46/0x69
	[<8137fa77>] sysenter_do_call+0x12/0x2

Cc: <stable@vger.kernel.org>
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Cc: Abhijit Pradhan <abhijit@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: NJohannes Berg <johannes.berg@intel.com>
Tested-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some devices (iwl5100) cannot connect to zd1211rw based AP. It appears that
zd1211 firmware messes up duration_id field if it is not set to zero by driver.

Sniffing traffic shows that zd1211 is transmitting frames with duration_id bits
14 and 15 set and other bits appearing random. Setting duration_id at driver to
zero results zd1211 outputting sane duration_id. This means that firmware is
setting correct values itself and expects duration_id to be zero in first
place.

Looking at vendor driver shows that only PSPoll frames have duration_id set by
driver, for other frames duration_id left zero.

Original bug-report and attached patch at:
  http://sourceforge.net/mailarchive/message.php?msg_id=28759111Reported-by: NTomas Vanek <Tomas.Vanek@fbl.cz>
[modified original patch from bug-report, added check for pspoll frame]
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The brcmsmac driver is now using the bcma SPROM CRC check, which does
not recognize all chipsets that were functional prior to the switch. In
particular, the current code bails out on odd CRC errors in recent
Macbooks. This patch ignores those errors, with the argument that an
unrecognized SPROM should be treated similarly to a non-existing one.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit adb5066a "ath9k_hw: do not apply the 2.4 ghz ack timeout
workaround to cts" reduced the hardware CTS timeout to the normal
values specified by the standard, but it turns out while it doesn't
need the same extra time that it needs for the ACK timeout, it
does need more than the value specified in the standard, but only
for 2.4 GHz.

This patch brings the CTS timeout value in sync with the initialization
values, while still allowing adjustment for bigger distances.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Reported-by: NSeth Forshee <seth.forshee@canonical.com>
Reported-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit b4a82a0 "ath9k_hw: fix interpretation of the rx KeyMiss flag"
fixed the interpretation of the KeyMiss flag for keycache based lookups,
however WEP encryption uses a static index, so KeyMiss is always asserted
for it, even though frames are decrypted properly.
Fix this by clearing the ATH9K_RXERR_KEYMISS flag if no keycache based
lookup was performed.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Reported-by: NLaurent Bonnans <bonnans.l@gmail.com>
Reported-by: NJurica Vukadin <u.ra604@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If driver load is failed, sometimes few pointers may remain
uninitialized ex. priv->wdev, priv->netdev, adapter->sleep_cfm
This will cause NULL pointer dereferance while unloading the
driver.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

all works need to be initialized before ieee80211_register_hw
to prevent mac80211 call backs such as drv_start, drv_config
getting started. otherwise we would queue/cancel works before
initializing them and it leads to kernel panic.
this issue can be recreated with the following script
in Chrome laptops with AR928X cards, with background scan
running (or) Network manager is running

while true
do
sudo modprobe -v ath9k
sleep 3
sudo modprobe -r ath9k
sleep 3
done

	 EIP: [<81040a47>] __cancel_work_timer+0xb8/0xe1 SS:ESP 0068:f6be9d70
	 ---[ end trace 4f86d6139a9900ef ]---
	 Registered led device: ath9k-phy0
	 ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xf88a0000,
	 irq=16
	 Kernel panic - not syncing: Fatal exception
	 Pid: 456, comm: wpa_supplicant Tainted: G      D
	 3.0.13 #1
	Call Trace:
	 [<81379e21>] panic+0x53/0x14a
	 [<81004a30>] oops_end+0x73/0x81
	 [<81004b53>] die+0x4c/0x55
	 [<81002710>] do_trap+0x7c/0x83
	 [<81002855>] ? do_bounds+0x58/0x58
	 [<810028cc>] do_invalid_op+0x77/0x81
	 [<81040a47>] ? __cancel_work_timer+0xb8/0xe1
	 [<810489ec>] ? sched_clock_cpu+0x81/0x11f
	 [<8103f809>] ? wait_on_work+0xe2/0xf7
	 [<8137f807>] error_code+0x67/0x6c
	 [<810300d8>] ? wait_consider_task+0x4ba/0x84c
	 [<81040a47>] ? __cancel_work_timer+0xb8/0xe1
	 [<810380c9>] ? try_to_del_timer_sync+0x5f/0x67
	 [<81040a91>] cancel_work_sync+0xf/0x11
	 [<f88d7b7c>] ath_set_channel+0x62/0x25c [ath9k]
	 [<f88d67d1>] ? ath9k_tx_last_beacon+0x26a/0x85c [ath9k]
	 [<f88d8899>] ath_radio_disable+0x3f1/0x68e [ath9k]
	 [<f90d0edb>] ieee80211_hw_config+0x111/0x116 [mac80211]
	 [<f90dd95c>] __ieee80211_recalc_idle+0x919/0xa37 [mac80211]
	 [<f90dda76>] __ieee80211_recalc_idle+0xa33/0xa37 [mac80211]
	 [<812dbed8>] __dev_open+0x82/0xab

Cc: <stable@vger.kernel.org>
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Tested-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently even if association is failed "iw link" shows some
information about connected BSS and "Tx timeout" error is seen in
dmesg log.

This patch fixes below issues in the code to handle assoc failure
case correctly.
1) "status" variable in mwifiex_wait_queue_complete() is not
correctly updated. Hence driver doesn't inform cfg80211 stack
about association failure.
2) During association network queues are stopped but carrier is
not cleared, which gives Tx timeout error in failure case
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The device seems to survive the issue, so no need to flood the logs
about it...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current code checks for stored_mpdu_num > 1, causing
the reorder_timer to be triggered indefinitely, but the
frame is never timed-out (until the next packet is received)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Cc: <stable@vger.kernel.org>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In my AMPDU rework, I rely on the sequence numbers of frames. But
I didn't check that the frame has a valid tid before updating the
tracking counters. As a result, the Tx queues were stalled. People
who hit this bug saw that we simply didn't let any data out.

This bug was introduced in 3.3.

This patch fixes that and checks that the frame is a QoS frame before
looking at its tid and changing the counters.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ssb supports one extra device on the cardbus. This results in two
devices in total, one beeing the host controller itself and the other
the external device connected to the hostcontroller over cardbus.

This makes the cardbus slot work on the Linksys WRT150N.
Reported-by: NAaron Z <aaronz@pls-net.org>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Average users either don't care or they think that message indicates a
problem...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch correct the type of variables containing the rssi
values read from the rxwi.

In function rt2800_agc_to_rssi() 3 variables (rssi0, rssi1, rss2)
defined as int was assigned a 16bit signed values as unsigned.
From a test with a hi-gain antenna I verified that the rxwi
contains signed rssi values in the  range -13/+81 (inclusive)
with 0 as an error condition. In case of negative values a
condition is triggered and the function return -128dBm while
the signal is at its maximum. This patch correct the cast so
negative values are not treated as very high positive values
(ex. -13 does not become 243).
Signed-off-by: NLuigi Tarenga <luigi.tarenga@gmail.com>
Reviewed-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

bcma_bus_scan() leaks 'struct bcma_device' bytes if
bcma_get_next_core() returns error.

Restructure the code so we always kfree() the memory we allocate to
the variable 'core' before it goes out of scope.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 0884d7aa (AF_UNIX: Fix poll blocking problem when reading from
a stream socket) added a regression for epoll() in Edge Triggered mode
(EPOLLET)

Appropriate fix is to use skb_peek()/skb_unlink() instead of
skb_dequeue(), and only call skb_unlink() when skb is fully consumed.

This remove the need to requeue a partial skb into sk_receive_queue head
and the extra sk->sk_data_ready() calls that added the regression.

This is safe because once skb is given to sk_receive_queue, it is not
modified by a writer, and readers are serialized by u->readlock mutex.

This also reduce number of spinlock acquisition for small reads or
MSG_PEEK users so should improve overall performance.
Reported-by: NNick Mathewson <nickm@freehaven.net>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Alexey Moiseytsev <himeraster@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit fixes tcp_trim_head() to recalculate the number of
segments in the skb with the skb's existing MSS, so trimming the head
causes the skb segment count to be monotonically non-increasing - it
should stay the same or go down, but not increase.

Previously tcp_trim_head() used the current MSS of the connection. But
if there was a decrease in MSS between original transmission and ACK
(e.g. due to PMTUD), this could cause tcp_trim_head() to
counter-intuitively increase the segment count when trimming bytes off
the head of an skb. This violated assumptions in tcp_tso_acked() that
tcp_trim_head() only decreases the packet count, so that packets_acked
in tcp_tso_acked() could underflow, leading tcp_clean_rtx_queue() to
pass u32 pkts_acked values as large as 0xffffffff to
ca_ops->pkts_acked().

As an aside, if tcp_trim_head() had really wanted the skb to reflect
the current MSS, it should have called tcp_set_skb_tso_segs()
unconditionally, since a decrease in MSS would mean that a
single-packet skb should now be sliced into multiple segments.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NNandita Dukkipati <nanditad@google.com>
Acked-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sysctl_tcp_mem() initialization was moved to sysctl_tcp_ipv4.c
in commit 3dc43e3e, since it
became a per-ns value.

That code, however, will never run when CONFIG_SYSCTL is
disabled, leading to bogus values on those fields - causing hung
TCP sockets.

This patch fixes it by keeping an initialization code in
tcp_init(). It will be overwritten by the first net namespace
init if CONFIG_SYSCTL is compiled in, and do the right thing if
it is compiled out.

It is also named properly as tcp_init_mem(), to properly signal
its non-sysctl side effect on TCP limits.
Reported-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NGlauber Costa <glommer@parallels.com>
Cc: David S. Miller <davem@davemloft.net>
Link: http://lkml.kernel.org/r/4F22D05A.8030604@parallels.com
[ renamed the function, tidied up the changelog a bit ]
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

caif is a subsystem and as such it needs to register with
register_pernet_subsys instead of register_pernet_device.

Among other problems using register_pernet_device was resulting in
net_generic being called before the caif_net structure was allocated.
Which has been causing net_generic to fail with either BUG_ON's or by
return NULL pointers.

A more ugly problem that could be caused is packets in flight why the
subsystem is shutting down.

To remove confusion also remove the cruft cause by inappropriately
trying to fix this bug.

With the aid of the previous patch I have tested this patch and
confirmed that using register_pernet_subsys makes the failure go away as
it should.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: NSasha Levin <levinsasha928@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By definition net_generic should never be called when it can return
NULL.  Fail conspicously with a BUG_ON to make it clear when people mess
up that a NULL return should never happen.

Recently there was a bug in the CAIF subsystem where it was registered
with register_pernet_device instead of register_pernet_subsys.  It was
erroneously concluded that net_generic could validly return NULL and
that net_assign_generic was buggy (when it was just inefficient).
Hopefully this BUG_ON will prevent people to coming to similar erroneous
conclusions in the futrue.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Tested-by: NSasha Levin <levinsasha928@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 36a12119 removed linux/module.h
include statement from one of the headers that end up in net/sock.h.
It was providing us with static_branch() definition implicitly, so
after its removal the build got broken.

To fix this, and avoid having this happening in the future,
let me do the right thing and include linux/jump_label.h
explicitly in sock.h.
Signed-off-by: NGlauber Costa <glommer@parallels.com>
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setting link parameters on a netdevice changes the value
of if_nlmsg_size(), therefore it is necessary to recalculate
min_ifinfo_dump_size.
Signed-off-by: NStefan Gula <steweg@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tunnel devices set NETIF_F_LLTX to bypass HARD_TX_LOCK.  Sit and
ipip set this unconditionally in ops->setup, but gre enables it
conditionally after parameter passing in ops->newlink. This is
not called during tunnel setup as below, however, so GRE tunnels are
still taking the lock.

modprobe ip_gre
ip tunnel add test0 mode gre remote 10.5.1.1 dev lo
ip link set test0 up
ip addr add 10.6.0.1 dev test0
 # cat /sys/class/net/test0/features
 # $DIR/test_tunnel_xmit 10 10.5.2.1
ip route add 10.5.2.0/24 dev test0
ip tunnel del test0

The newlink callback is only called in rtnl_netlink, and only if
the device is new, as it calls register_netdevice internally. Gre
tunnels are created at 'ip tunnel add' with ioctl SIOCADDTUNNEL,
which calls ipgre_tunnel_locate, which calls register_netdev.
rtnl_newlink is called at 'ip link set', but skips ops->newlink
and the device is up with locking still enabled. The equivalent
ipip tunnel works fine, btw (just substitute 'method gre' for
'method ipip').

On kernels before /sys/class/net/*/features was removed [1],
the first commented out line returns 0x6000 with method gre,
which indicates that NETIF_F_LLTX (0x1000) is not set. With ipip,
it reports 0x7000. This test cannot be used on recent kernels where
the sysfs file is removed (and ETHTOOL_GFEATURES does not currently
work for tunnel devices, because they lack dev->ethtool_ops).

The second commented out line calls a simple transmission test [2]
that sends on 24 cores at maximum rate. Results of a single run:

ipip:			19,372,306
gre before patch:	 4,839,753
gre after patch:	19,133,873

This patch replicates the condition check in ipgre_newlink to
ipgre_tunnel_locate. It works for me, both with oseq on and off.
This is the first time I looked at rtnetlink and iproute2 code,
though, so someone more knowledgeable should probably check the
patch. Thanks.

The tail of both functions is now identical, by the way. To avoid
code duplication, I'll be happy to rework this and merge the two.

[1] http://patchwork.ozlabs.org/patch/104610/
[2] http://kernel.googlecode.com/files/xmit_udp_parallel.cSigned-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NWei Liu <wei.liu2@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a new net namespace is created, we should attach to it a "struct
net_generic" with enough slots (even empty), or we can hit the following
BUG_ON() :

[  200.752016] kernel BUG at include/net/netns/generic.h:40!
...
[  200.752016]  [<ffffffff825c3cea>] ? get_cfcnfg+0x3a/0x180
[  200.752016]  [<ffffffff821cf0b0>] ? lockdep_rtnl_is_held+0x10/0x20
[  200.752016]  [<ffffffff825c41be>] caif_device_notify+0x2e/0x530
[  200.752016]  [<ffffffff810d61b7>] notifier_call_chain+0x67/0x110
[  200.752016]  [<ffffffff810d67c1>] raw_notifier_call_chain+0x11/0x20
[  200.752016]  [<ffffffff821bae82>] call_netdevice_notifiers+0x32/0x60
[  200.752016]  [<ffffffff821c2b26>] register_netdevice+0x196/0x300
[  200.752016]  [<ffffffff821c2ca9>] register_netdev+0x19/0x30
[  200.752016]  [<ffffffff81c1c67a>] loopback_net_init+0x4a/0xa0
[  200.752016]  [<ffffffff821b5e62>] ops_init+0x42/0x180
[  200.752016]  [<ffffffff821b600b>] setup_net+0x6b/0x100
[  200.752016]  [<ffffffff821b6466>] copy_net_ns+0x86/0x110
[  200.752016]  [<ffffffff810d5789>] create_new_namespaces+0xd9/0x190

net_alloc_generic() should take into account the maximum index into the
ptr array, as a subsystem might use net_generic() anytime.

This also reduces number of reallocations in net_assign_generic()
Reported-by: NSasha Levin <levinsasha928@gmail.com>
Tested-by: NSasha Levin <levinsasha928@gmail.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Sjur Brændeland <sjur.brandeland@stericsson.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Port autoselection finds a port and then drop the lock,
then right after that, gets the hash bucket again and lock it.

Fix it to go direct.
Signed-off-by: NFlavio Leitner <fbl@redhat.com>
Signed-off-by: NMarcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code checks for conflicts when the application
requests a specific port.  If there is no conflict, then
the request is granted.

On the other hand, the port autoselection done by the kernel
fails when all ports are bound even when there is a port
with no conflict available.

The fix changes port autoselection to check if there is a
conflict and use it if not.
Signed-off-by: NFlavio Leitner <fbl@redhat.com>
Signed-off-by: NMarcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>