Additionally, add wow_enabled field to wl, to indicate
whether wowlan was configured.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

set the sdio interrupt as wake_up interrupt, so we will be able
to wake up the suspended system (Wake-On-Wireless)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This flag is not used anymore, remove it from the list.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The current firmware only supports scheduled scan in station mode and
when idle.  To prevent the firmware from crashing, return -EOPNOTSUPP
when sched_scan start is called in an invalid state.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add the sched_scanning value to the driver_status debugfs entry.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This patch adds the mac80211 operations for scheduled scan and the
scheduled scan results reporting.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add firmware command structures, definitions and code to to configure,
start and stop scheduled scans.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Subscribe and listen to PERIODIC_SCAN_REPORT_EVENT_ID and
PERIODIC_SCAN_COMPLETE_EVENT_ID in preparation for the scheduled scan
implementation.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Add the structures and values for driver-configured scheduled scan
parameters.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Set the spectrum management bit in the hw flags so that mac80211 will
set the WLAN_CAPABILITY_SPECTRUM_MGMT bit in association requests
(which in practice means that we support 802.11h spectrum management).

[Reworded the commit log -- Luca.]
Signed-off-by: NShahar Levi <shahar_levi@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This patch adds a beacon filter rule to pass up the beacons that
contain changed HT information elements.  These beacons need to be
passed to mac80211 so that it can act on such changes.

[Reworded commit log -- Luca.]
Signed-off-by: NShahar Levi <shahar_levi@ti.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Simplify wl1271_ssid_set by re-using cfg80211_find_ie instead of
reimplementing it.

Additionally, add a length check to prevent a potential buffer overflow.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

There's no need to have table functions in one
file and all users in another, move the functions
to the right file and make them static. Also move
a static variable to the beginning of the file to
make it easier to find.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When sched_scan_stopped was called by the driver, mac80211 calls
cfg80211, which in turn was calling mac80211 back with a flag
"driver_initiated".  This flag was used so that mac80211 would do the
necessary cleanup but would not call the driver.  This was enough to
prevent the bounce back between the driver and mac80211, but not
between mac80211 and cfg80211.

To fix this, we now do the cleanup in mac80211 before calling
cfg80211.  To help with locking issues, the workqueue was moved from
cfg80211 to mac80211.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A few configuration functions correctly do
rcu_read_lock() but don't correctly reference
some pointers protected by RCU. Fix that.

Cc: stable@kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code here is only not racy because all the
places that assign the pointers it uses are
holding the sta_mtx as well as the key_mtx and
so can't race against this because this code
holds the sta_mtx. But that's not intuitive,
so fix it to hold the key_mtx.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code in ieee80211_del_key() doesn't acquire the
key_mtx properly when it dereferences the keys. It
turns out that isn't actually necessary since the
key_mtx itself seems to be redundant since all key
manipulations are done under the RTNL, but as long
as we have the key_mtx we should use it the right
way too.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code here to RCU-dereference a pointer that's
on the stack is totally pointless, RCU isn't magic
(like say Java's weak references are), so the code
can't work like whoever wrote it thought it might.

Remove it so readers don't get confused. Note that
it seems that a bug is there anyway: I don't see
any code that cancels the timer when a mesh path
struct is destroyed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

XB113 (AR9380) 3x3 SB 5G only cards were failing to connect to APs
due to incorrect xpabiaslevel configuration. fix it.

Cc: stable@kernel.org
Cc: Ray Li <ray.li@greenwavereality.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: compat@orbit-lab.org
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function
- increments dropped rx_packet count if status code
  passed to it is "-1".
- frees SKB buffer.

But currently the function is being called with "0" status code.
This patch replaces above function by dev_kfree_skb_any() call.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The XB113 cards are single band, 5 GHz-only, but the
default settings were configured to assume it was dual
band. Users of these cards then would see 2.4 GHz channels
but you would never get any scan results from these channels
given that the radio is not present.

Cc: stable@kernel.org
Cc: Fiona Cain <Fiona.Cain@atheros.com>
Cc: Ray Li <ray.li@greenwavereality.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Dan Friedman <dan.friedman@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When transmitting a frame, the transmitter waits a random number of
slots between 0 and cw. Thus, the contention time is (cw / 2) * t_slot
which we can represent instead as (cw * t_slot) >> 1. Also fix a few
other accounting bugs around contention time, and add comments.
Signed-off-by: NDaniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Multiple virtual AP interfaces can currently try
to use different beacon intervals, but that just
leads to problems since it won't actually be done
that way by drivers. Return an error in this case
to make sure it won't be done wrong.

Also, ignore attempts to change the DTIM period
or beacon interval during the lifetime of the BSS.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

net/mac80211/cfg.c: In function ‘sta_apply_parameters’:
net/mac80211/cfg.c:746: error: ‘struct sta_info’ has no member named ‘plink_state’
make[1]: *** [net/mac80211/cfg.o] Error 1
make: *** [net/mac80211/mac80211.ko] Error 2
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

They were added by me while testing and I forgot to remove.
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

If we can't find a ACL link between the devices, we search
the connection list one second time looking for LE links.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

We need to be able for receive events notifying that the connection
was established, the connection attempt failed or that disconnection
happened.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Introduce NL80211_ATTR_SCHED_SCAN_INTERVAL as a required attribute for
NL80211_CMD_START_SCHED_SCAN.  This value informs the driver at which
intervals the scheduled scan cycles should be executed.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement support for HW scheduled scan.  The mac80211 code doesn't perform
scheduled scans itself, but calls the driver to start and stop scheduled
scans.

This patch also creates a trace event class to be used by drv_hw_scan
and the new drv_sched_scan_start and drv_sched_stop functions, in
order to avoid duplicate code.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement new functionality for scheduled scan offload.  With this feature we
can scan automatically at certain intervals.

The idea is that the hardware can perform scan automatically and filter on
desired results without waking up the host unnecessarily.

Add NL80211_CMD_START_SCHED_SCAN and NL80211_CMD_STOP_SCHED_SCAN
commands to the nl80211 interface.  When results are available they are
reported by NL80211_CMD_SCHED_SCAN_RESULTS events.  The userspace is
informed when the scheduled scan has stopped with a
NL80211_CMD_SCHED_SCAN_STOPPED event, which can be triggered either by
the driver or by a call to NL80211_CMD_STOP_SCHED_SCAN.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This allows individual users and deployments to disable mesh support at
runtime, i.e. without having to build and maintain a custom kernel.

Based on a patch by Paul Fox <pgf@laptop.org>.
Signed-off-by: NSascha Silbe <silbe@activitycentral.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some structures and macros in ioctl.h are redundant or no longer
used.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Avoid use of local structure in the function if the structure is
already allocated by the caller and the structure pointer is passed.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Documented in: <4DCA7E40.9070709@lwfinger.net>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commiting settings is possible on devices without PCI core (but with CC
core). Export it for usage in drivers supporting other cores.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Similar patch was commited to ssb.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Only leave filtering enabled for AP or VLAN interfaces, clear the
destination mask for all other interfaces.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Reported-by: NBen Greear <greearb@candelatech.com>
Tested-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is not N-PHY specific function, we partially duplicate code.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>