Sending I/O through 32 bit descriptors to Ventura series of controller
results in IO timeout on certain conditions. This error only occurs on
systems with high I/O activity.

Changes in this patch will prevent driver from using 32 bit descriptor
and use 64 bit Descriptors
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If the posted request has an error of any type, the IOC writes
a Reply message into a host-based system reply message frame.
This functions clone it in the BAR0 mapped region.
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

1) Added function _base_clone_mpi_to_sys_mem to clone
MPI request into system BAR0 mapped region.

2) Separate out MPI Endpoint IO submissions to function
_base_put_smid_mpi_ep_scsi_io.

3) MPI EP requests are submitted in two 32 bit MMIO writes.
from _base_mpi_ep_writeq.

 For 32 bit Arch,_base_writeq function is identical
to _base_mpi_ep_writeq, Removed duplicate code as suggested.
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

All scsi IO's and config request's data buffer and sgl are cloned to
system memory in _clone_sg_entries before submitting it to firmware.
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For MPI Endpoint/Mcpu, driver should double buffer data buffer/SGLs.
This is normally copied from host to internal memory of IOC by DMA
engine of PCI device. Since the interface to DMA from host to mCPU is
not present for Mcpu/MPI Endpoint device, driver does double copy of
those buffers directly to the mCPU memory region via BAR0 region.

Introduced API to calculate and return BAR0 mapped host buffer's
physical and virtual address for the provided smid.
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This configures shost max sector to 128, single reply descriptor post
queue, sgl table size to 16 and 32 bit DMA for MPI Endpoint and it
supports 64K as max IO.
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The function _get_st_from_smid is local to the source and does not need
to be in global scope, so make it static.

Cleans up sparse warning:
symbol '_get_st_from_smid' was not declared. Should it be static?
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Performance improvement using block layer tag.

Curent driver gets scsiio tracker and free smid from link list and array
based tracking managed by driver.  Accessing list in main io path is
performance pentaly because of protection using spinlock
"scsi_lookup_lock".

In this patch:

1. Driver removes all link list access from main io path and
   use scmd->request->tag to get free smid.

2. Instead of holding 'struct scsiio_tracker' in its own pool
   driver can embed it into the scsi command.

Driver provides cmd_size in scsi_host_template, so that struct
scsiio_tracker is preallocated by scsi mid layer for each scsi command.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use 'host_busy' instead of counting outstanding commands by hand.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

ioctl passthrough commands require a SCSIIO smid, but cannot easily
integrate with the block layer. But the driver already has reserved some
SCSIIO smids and we're only ever allowing one ioctl command at a time we
can use the first reserved smid for ioctl commands.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Abstract accesses to the scsi_lookup array by introducing
mpt3sas_get_st_from_smid().
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

No functional change.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use 'list_splice_init()' instead of hand-crafted function.  No
functional change.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

No functional change
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The newly added base_make_prp_nvme function triggers a build warning on
some 32-bit configurations:

drivers/scsi/mpt3sas/mpt3sas_base.c: In function 'base_make_prp_nvme':
drivers/scsi/mpt3sas/mpt3sas_base.c:1664:13: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
  msg_phys = (dma_addr_t)mpt3sas_base_get_pcie_sgl_dma(ioc, smid);

After taking a closer look, I found that the problem is that the new
code mixes up pointers and dma_addr_t values unnecessarily.

This changes it to use the correct types consistently, which lets us get
rid of a lot of type casts in the process. I'm also renaming some
variables to avoid confusion between physical and dma address spaces
that are often distinct.

Fixes: 016d5c35 ("scsi: mpt3sas: SGL to PRP Translation for I/Os to NVMe devices")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

1) Used variable __le64/__le32 whichever required in building NVME
PRP, and passed to LE Controller.

2) Remove unused functions, And Declared functions as static which are
used only in mpt3sas_scsih.c.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

* The controller firmware sends separate events for NVMe devices and
  PCIe switches similar to existing SAS events.

* NVMe device detection, addition and removal are reported by the
  firmware through PCIe Topology Change list events.

* The PCIe device state change events are sent when the firmware
  detects any abnormal conditions with a NVMe device or switch.

* The enumeration event are sent when the firmware starts PCIe device
  enumeration and stops.

* This patch has the code change to handle the events and add/remove
  NVMe devices in driver's inventory.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

* Mpt3sas driver uses the NVMe Encapsulated Request message to send an
  NVMe command to an NVMe device attached to the IOC.

* Normal I/O commands like reads and writes are passed to the
  controller as SCSI commands and the controller has the ability to
  translate the commands to NVMe equivalent.

* This encapsulated NVMe command is used by applications to send
  direct NVMe commands to NVMe drives.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

* Added support for translating the SGLs associated with incoming
commands either to IEE SGL or NVMe PRPs for NVMe devices.

* The hardware translation of IEEE SGL to NVMe PRPs has limitations
and if a command cannot be translated by hardware then it will go to
firmware and the firmware needs to translate it. This will have a
performance impact. To avoid that, the driver proactively checks
whether the translation will be done in hardware or not. If not, then
driver translates.

[mkp: clarified commit message]
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:

@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@

 module_param_call(_name, _set_func, _get_func, _arg, _mode);

@fix_set_prototype
 depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@

 int _set_func(
-_val_type _val
+const char * _val
 ,
-_param_type _param
+const struct kernel_param * _param
 ) { ... }

@fix_get_prototype
 depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@

 int _get_func(
-_val_type _val
+char * _val
 ,
-_param_type _param
+const struct kernel_param * _param
 ) { ... }

Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:

	drivers/platform/x86/thinkpad_acpi.c
	fs/lockd/svc.c
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NJessica Yu <jeyu@kernel.org>

To reduce the memory footprint of the driver in the kdump kernel, we
apply the following settings when reset_devices is set:

1. Use single MSI-x vector.
2. Disable RDPQ mode.
3. Set sg_table_size to 32 by default.
4) Set SCSI IO Queue depth to 200.

[mkp: fixed commit message]
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Earlier Active Cable Exception event with reason code "Cable Degraded
(0x02))" was added only for Active Cable. Now this event is extended to
Passive cable too. Re-arranged display message accordingly.

Also added Cable Exception Event event for SAS3008 & SAS3108 HBAs
(i.e. MPI 2.5 spec supporting HBAs). Previously, this event was enabled
only for MPI 2.6 spec supporting HBA devices.

[mkp: typos]
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

An optional discovery status should be printed with a pr_cont and needs
a leading space to make it more readable. The final new line should also
be a pr_cont and the indentation is out by one, so fix that too.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In the lines above this test, 8 'kzalloc' are performed, but only 7
results are tested.

Add the missing one (i.e. '!ioc->port_enable_cmds.reply').
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.
Signed-off-by: NRomain Perier <romain.perier@collabora.com>
Reviewed-by: NPeter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Due to relaxed ordering requirements on multiple architectures, drivers
are required to use wmb/rmb/mb combinations when they need to guarantee
observability between the memory and the HW.

The mpt3sas driver is already using wmb() for this purpose.  However, it
issues a writel following wmb(). writel() function on arm/arm64
arhictectures have an embedded wmb() call inside.

This results in unnecessary performance loss and code duplication.

writel already guarantees ordering for both cpu and bus. we don't need
additional wmb()
Signed-off-by: NSinan Kaya <okaya@codeaurora.org>
Acked-by: NSreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Cleanup the MSI-X handling allowing us to use the PCI-layer provided
vector allocation.
Signed-off-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NSreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Due existence of loop in the IO path our HBA will receive heavy IOs and
also as driver is not updating the Reply Post Host Index frequently, So
there will be a high chance that our Firmware unable to find any free
entry in the Reply Post Descriptor Queue (i.e. Queue overflow occurs)
and can observe 0x2100 firmware fault.  So to fix this, we have defined
a thresh hold value. After continuously processing this thresh hold
number of reply descriptors driver will update the Reply Descriptor Host
Index so that this thresh hold number of reply descriptors entries will
be freed and these entries will be available for firmware and we won't
observe this Firmware fault. We have defined this threshold value as
1/3rd of the hba queue depth.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Small glitch/degraded performance in Crusader is improved with SAS
drives by removing unnecessary spinlocks while clearing scsi command in
drivers internal lookup table.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Support Atomic Request Descriptors for Ventura/SAS35 devices.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For SAS35 devices MSIX vectors are inceased to 128 from 96. To support this
Reply post host index register count is increased to 16. Also variable
msix96_vector is replaced with combined_reply_queue and variable
combined_reply_index_count is added to set different values for SAS3 and
SAS35 devices.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When device missing event arrives, device_remove_in_progress bit will be
set and hence driver has to stop sending IOCTL commands.Now the check has
been added in IOCTL path to test device_remove_in_progress bit is set, if
so then IOCTL will be failed printing failure message.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Fix for incorrect numbers for MSIX vectors enabled when non RDPQ card is enumerated first.

No. of MSIX vectors supported = min (Total no. of CPU cores,
MSIX vectors supported by card)

when RDPQ is disabled "max_msix_vectors" module parameter which was
declared as global was set to '8' and hence if there are more than one card
in system among which if RDPQ disabled card is enumerated first then only 8
MSIX vectors was getting enabled for all the cards(including RDPQ enabled
card,which can support more than 8 MSIX vectors).

Used local variable instead of global variable ,if RDPQ is disabled this
local variable is set to '8' else it is set to "max_msix_vectors" (by
default this is set to -1, whose value can be set by user during driver
load time).So now regardless of whether RDPQ disabled card is enumerated
first or RDPQ enabled card is enumerated first , MSIX vectors enabled
depends on the cards capability.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

mpt3sas crashes on resume after suspend with WarpDrive flash cards.  The
reply_post_host_index array is not set back up after the resume, and we
deference a stale pointer in _base_interrupt().

[   47.309711] BUG: unable to handle kernel paging request at ffffc90001f8006c
[   47.318289] IP: [<ffffffffc00863ef>] _base_interrupt+0x49f/0xa30 [mpt3sas]
[   47.326749] PGD 41ccaa067 PUD 41ccab067 PMD 3466c067 PTE 0
[   47.333848] Oops: 0002 [#1] SMP
...
[   47.452708] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.7.0 #6
[   47.460506] Hardware name: Dell Inc. OptiPlex 990/06D7TR, BIOS A18 09/24/2013
[   47.469629] task: ffffffff81c0d500 ti: ffffffff81c00000 task.ti: ffffffff81c00000
[   47.479112] RIP: 0010:[<ffffffffc00863ef>]  [<ffffffffc00863ef>] _base_interrupt+0x49f/0xa30 [mpt3sas]
[   47.490466] RSP: 0018:ffff88041d203e30  EFLAGS: 00010002
[   47.497801] RAX: 0000000000000001 RBX: ffff880033f4c000 RCX: 0000000000000001
[   47.506973] RDX: ffffc90001f8006c RSI: 0000000000000082 RDI: 0000000000000082
[   47.516141] RBP: ffff88041d203eb0 R08: ffff8804118e2820 R09: 0000000000000001
[   47.525300] R10: 0000000000000001 R11: 00000000100c0000 R12: 0000000000000000
[   47.534457] R13: ffff880412c487e0 R14: ffff88041a8987d8 R15: 0000000000000001
[   47.543632] FS:  0000000000000000(0000) GS:ffff88041d200000(0000) knlGS:0000000000000000
[   47.553796] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   47.561632] CR2: ffffc90001f8006c CR3: 0000000001c06000 CR4: 00000000000406f0
[   47.570883] Stack:
[   47.575015]  000000001d211228 ffff88041d2100c0 ffff8800c47d8130 0000000000000100
[   47.584625]  ffff8804100c0000 100c000000000000 ffff88041a8992a0 ffff88041a8987f8
[   47.594230]  ffff88041d203e00 ffffffff81111e55 000000000000038c ffff880414ad4280
[   47.603862] Call Trace:
[   47.608474]  <IRQ>
[   47.610413]  [<ffffffff81111e55>] ? call_timer_fn+0x35/0x120
[   47.620539]  [<ffffffff81100a1f>] handle_irq_event_percpu+0x7f/0x1c0
[   47.629061]  [<ffffffff81100b8c>] handle_irq_event+0x2c/0x50
[   47.636859]  [<ffffffff81103fff>] handle_edge_irq+0x6f/0x130
[   47.644654]  [<ffffffff8102fbf3>] handle_irq+0x73/0x120
[   47.652011]  [<ffffffff810c6ada>] ? atomic_notifier_call_chain+0x1a/0x20
[   47.660854]  [<ffffffff817e374b>] do_IRQ+0x4b/0xd0
[   47.667777]  [<ffffffff817e160c>] common_interrupt+0x8c/0x8c
[   47.675635]  <EOI>

Move the reply_post_host_index array setup into
mpt3sas_base_map_resources(), which is also in the resume path.

Cc: stable@vger.kernel.org
Signed-off-by: NGreg Edwards <gedwards@fireweed.org>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Trivial non-functional changes for a couple annoying things:

  1) Functions local to files are not declared static, which is
  frustrating when reading the code because it's non-obvious at first
  glance what's actually called from other files.

  2) Set-but-unused variables abound, presumably to mask -Wunused-result
  errors in the past. None of these are flagged today though (with one
  exception noted below), so remove them.

Fixing (2) exposed the fact that we improperly ignore the return value
of scsi_device_reprobe() in _scsih_reprobe_lun(). Fixing the calling
code to deal with the potential error is non-trivial, so for now just
WARN().
Signed-off-by: NCalvin Owens <calvinowens@fb.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

With the exception of a single call to wait_for_doorbell_int(), all this
conditional sleeping code is dead. So delete it.
Signed-off-by: NCalvin Owens <calvinowens@fb.com>
Acked-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Replaced mpt3sas_base_flush_reply_queues() with
mpt3sas_base_sync_reply_irqs(),as mpt3sas_base_flush_reply_queues()
skips over reply queues that are currently busy (i.e. being handled by
interrupt processing in another core). If a reply queue is busy, then
call to synchronize_irq()in mpt3sas_base_sync_reply_irqs()make sures the
other core has finished flushing the queue and completed any calls to
the mid-layer scsi_done() routine.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In-order to handle this 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
driver need to follow below steps,
1. Unmask the 'MPI2_EVENT_ACTIVE_CABLE_EXCEPTION' event,
so that FW can notify this event to host driver.
2. After receiving this event, add this event to AEN event queue,
for notifying this event to applications.
3. Then Print below message in kernel logs if the event data's reason
code is zero,
"Currently an active cable with ReceptacleID <ID_Value> cannot be powered
and devices connected to this active cable will not be seen. This active
cable requires <PowerValue_in_mW> of power"

This event is only for Intruder/Cutlass HBAs.
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

'struct timeval' will have its tv_sec value overflow on 32-bit systems
in year 2038 and beyond. This patch replaces the use of struct timeval
for computing mpi_request.TimeStamp, and instead uses ktime_t which
provides 64-bit seconds value. The timestamp computed remains
unaffected (milliseconds since Unix epoch).
Signed-off-by: NTina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Acked-by: NSathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>