Many decoders require a trailing space (period without IR illumination)
to be delivered before completing a decode.

Since the gpio-ir-recv driver only delivers events on gpio transitions,
a single IR symbol (caused by a quick touch on an IR remote) will not
be properly decoded without the use of a timer to flush the tail end
state of the IR receiver.

This patch initializes and uses a timer and the timeout field of rcdev
to complete the stream and allow decode.

The timeout can be overridden through the use of the LIRC_SET_REC_TIMEOUT
ioctl.
Signed-off-by: NEric Nelson <eric@nelint.com>
Acked-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

A default timeout value of 125 ms should work for all decoders.

Declare a constant to help standardize its' use.
Signed-off-by: NEric Nelson <eric@nelint.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The device is set as wakeup capable using proper wakeup API but the
driver misuses IRQF_NO_SUSPEND to set the interrupt as wakeup source
which is incorrect.

This patch removes the use of IRQF_NO_SUSPEND flags replacing it with
enable_irq_wake instead.

Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: kernel@stlinux.com
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

commit f934a94b ('s5c73m3: Export OF
module alias information') broke compilation when compiled as module:

In file included from drivers/media/i2c/s5c73m3/s5c73m3-spi.c:22:0:
drivers/media/i2c/s5c73m3/s5c73m3-spi.c:40:40: error: expected ')' before ';' token
 MODULE_DEVICE_TABLE(of, s5c73m3_spi_ids;);
                                        ^

Fix it by removing the extra ';'
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

reset-gpios is more clear than rst-gpio.

This change has been done as one atomic commit but it
does breaks compatability with older dtbs.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds in the required DT node for the c8sectpfe
Linux DVB demux driver which allows the tsin channels
to be used on an upstream kernel.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Adding these properties makes the I2C bus to the demodulators much
more reliable, and we no longer suffer from I2C errors when tuning.
Signed-off-by: NPeter Griffin <peter.griffin@linaro.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

When in FE_TUNE_MODE_ONESHOT the frontend must report
the actual capabilities so user can take appropriate
action.

With frontends that can't do auto inversion this is done
by dvb-core automatically so CAN_INVERSION_AUTO is valid.

However, when in FE_TUNE_MODE_ONESHOT this is not true.

So only set FE_CAN_INVERSION_AUTO in modes other than
FE_TUNE_MODE_ONESHOT
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The SPI core always reports the MODALIAS uevent as "spi:<modalias>"
regardless of the mechanism that was used to register the device
(i.e: OF or board code) and the table that is used later to match
the driver with the device (i.e: SPI id table or OF match table).

So drivers needs to export the SPI id table and this be built into
the module or udev won't have the necessary information to autoload
the needed driver module when the device is added.

But this means that OF-only drivers needs to have both OF and SPI id
tables that have to be kept in sync and also the dev node compatible
manufacturer prefix is stripped when reporting the MODALIAS. Which can
lead to issues if two vendors use the same SPI device name for example.

To avoid the above, the SPI core behavior may be changed in the future
to not require an SPI device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table even when
is unused now to prevent breaking module loading when the core changes.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/media/pci/ddbridge/ddbridge-core.c:89
        incorrect check for negative return

Return type of wait_event_timeout is signed long not int and the
return type is >=0 always thus the negative check is unnecessary..
As stat is used here exclusively its type is simply changed and the
negative return check dropped.
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

These v4l2_ctrl_ops structures are never modified, like all the other
v4l2_ctrl_ops structures, so declare them as const.

Done with the help of Coccinelle.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch enable Atmel ISI preview path to convert the YUV to RGB format.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
[g.liakhovetski@gmx.de: removed superfluous parentheses]
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The preview path only can convert UYVY format to RGB data.

To make preview path work correctly, we need to set up YCC_SWAP
according to sensor output and convert them to UYVY.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Not like codec path, preview path can do downsampling, so we should setup
a extra preview width, height for it.

This patch add preview resolution setup without down sampling. So currently
preview path will output same size as sensor output size.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Atmel ISI support a preview path which can output RGB data.

So this patch introduces a bool variable to choose which path is
enabled currently. And also we need setup corresponding path registers.

By default the preview path is disabled. We only use Codec path.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

we need to configure the YCC_SWAP bits in ISI_CFG2 according to current
sensor output and Atmel ISI output format.

Current there are two cases Atmel ISI supported:
  1. Atmel ISI outputs YUYV format.
     This case we need to setup YCC_SWAP according to sensor output
     format.
  2. Atmel ISI output a pass-through formats, which means no swap.
     Just setup YCC_SWAP as default with no swap.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The soc-camera host will be probed and register a v4l2_clk, but if at
that moment, the i2c device is not available, then the registered
v4l2_clk name is an OF string not a I2C string.

So when i2c sensor probes and calls v4l2_clk_get(), it only searches a
clock with I2C string, like "1-0030".

This patch will search the clock with OF string name if no clock with
I2C string name could be found.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Make all v4l2-clk's clock name use V4L2_CLK_NAME_SIZE definition.

In future, if the string is increased we just need to change the
V4L2_CLK_NAME_SIZE once.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This macro is used to generate an OF string for a v4l2 clock.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Since v4l2_clk_name_i2c() is defined, reuse it.
Signed-off-by: NJosh Wu <josh.wu@atmel.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

With this patch, vivid capture thread can now generate a video with
frame rate reduced by a factor of 1000 / 1001. This option can be
selected using a control Reduced Framerate from gui.
Signed-off-by: NPrashant Laddha <prladdha@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

A boolean control Reduced Framerate is added to vivid controls for
controlling the reduced fps option for vivid capture from gui.
Signed-off-by: NPrashant Laddha <prladdha@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

If reduced fps flag is set then check if other necessary conditions
are true for the given bt timing. If yes, then reduce the frame rate.
For vivid transmitter, timeperframe_vid_out controls the frame rate.
Adjusting the timeperframe_vid_out by scaling down pixel clock by
factor of 1000 / 1001.
Signed-off-by: NPrashant Laddha <prladdha@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Added a helper function to check necessary conditions required for
reduced fps. The reduced fps is supported for CVT and CEA861 timings.
CVT supports reduced fps only if reduced blanking v2 (indicated by
vsync = 8) is true. Whereas CEA861 supports reduced fps if
V4L2_DV_FL_CAN_REDUCE_FPS flag is true.
Signed-off-by: NPrashant Laddha <prladdha@cisco.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

When a V4L2 sub-device backed by a DT or ACPI based device was removed,
the device was unregistered as well which certainly was not intentional,
as the client device would not be re-created by simply reinstating the
V4L2 sub-device (indeed the device would have to be there first!).

Skip unregistering the device in case it has non-NULL of_node or fwnode.
Signed-off-by: NTommi Franttila <tommi.franttila@intel.com>
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Initialization of the ADV7180 chip fails on the Renesas R8A7790-based
Lager board about 50% of the time.  This patch resolves the issue by
increasing the minimum delay after reset from 2 ms to 5 ms, following the
recommendation in the ADV7180 datasheet:

"Executing a software reset takes approximately 2 ms. However, it is
recommended to wait 5 ms before any further I2C writes are performed."
Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This fixes the crash reported in:
http://seclists.org/bugtraq/2015/Oct/35
The interface number needs a sanity check.
Signed-off-by: NOliver Neukum <oneukum@suse.com>
Cc: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The sh-vou driver has been converted from videobuf to videobuf2, but
the Kconfig file still lists VIDEOBUF_DMA_CONTIG as a dependency.
Consequently we can build the driver without VIDEOBUF2_DMA_CONTIG
and get a link error:

drivers/built-in.o: In function `sh_vou_probe':
vf610-ocotp.c:(.text+0x2dbf5c): undefined reference to `vb2_dma_contig_init_ctx'
vf610-ocotp.c:(.text+0x2dc0b4): undefined reference to `vb2_dma_contig_cleanup_ctx'
vf610-ocotp.c:(.text+0x2dc144): undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `sh_vou_remove':
vf610-ocotp.c:(.text+0x2dc190): undefined reference to `vb2_dma_contig_cleanup_ctx'

This changes the dependency to VIDEOBUF2_DMA_CONTIG instead.

Fixes: 57af3ad5 ("[media] sh-vou: convert to vb2")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

cpia2_usb_disconnect() seems to be missing a memory barrier which might
cause the waker to not notice the waiter and miss sending a wake_up as
in the following figure.

	cpia2_usb_disconnect			sync
------------------------------------------------------------------------
					mutex_unlock(&cam->v4l2_lock);
if (waitqueue_active(&cam->wq_stream))
/* The CPU might reorder the test for
   the waitqueue up here, before
   prior writes complete */
					/* wait_event_interruptible */
					 /* __wait_event_interruptible */
					  /* ___wait_event */
					  long __int = prepare_to_wait_event(
					    &wq, &__wait, state);
					  if (!cam->streaming ||
					    frame->status == FRAME_READY)
cam->curbuff->status = FRAME_READY;
cam->curbuff->length = 0;
					  schedule()
------------------------------------------------------------------------

The attached patch removes the call to waitqueue_active() leaving just
wake_up() behind.  This fixes the problem because the call to
spin_lock_irqsave() in wake_up() will be an ACQUIRE operation.

I found this issue when I was looking through the linux source code
for places calling waitqueue_active() before wake_up*(), but without
preceding memory barriers, after sending a patch to fix a similar
issue in drivers/tty/n_tty.c  (Details about the original issue can be
found here: https://lkml.org/lkml/2015/9/28/849).
Signed-off-by: NKosuke Tatsukawa <tatsu@ab.jp.nec.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

v4l2-compliance sends a zeroed struct v4l2_streamparm in
v4l2-test-formats.cpp::testParmType(), and this results in a division by
0 in some gspca subdrivers:

  divide error: 0000 [#1] SMP
  Modules linked in: gspca_ov534 gspca_main ...
  CPU: 0 PID: 17201 Comm: v4l2-compliance Not tainted 4.3.0-rc2-ao2 #1
  Hardware name: System manufacturer System Product Name/M2N-E SLI, BIOS
    ASUS M2N-E SLI ACPI BIOS Revision 1301 09/16/2010
  task: ffff8800818306c0 ti: ffff880095c4c000 task.ti: ffff880095c4c000
  RIP: 0010:[<ffffffffa079bd62>]  [<ffffffffa079bd62>] sd_set_streamparm+0x12/0x60 [gspca_ov534]
  RSP: 0018:ffff880095c4fce8  EFLAGS: 00010296
  RAX: 0000000000000000 RBX: ffff8800c9522000 RCX: ffffffffa077a140
  RDX: 0000000000000000 RSI: ffff880095e0c100 RDI: ffff8800c9522000
  RBP: ffff880095e0c100 R08: ffffffffa077a100 R09: 00000000000000cc
  R10: ffff880067ec7740 R11: 0000000000000016 R12: ffffffffa07bb400
  R13: 0000000000000000 R14: ffff880081b6a800 R15: 0000000000000000
  FS:  00007fda0de78740(0000) GS:ffff88012fc00000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00000000014630f8 CR3: 00000000cf349000 CR4: 00000000000006f0
  Stack:
   ffffffffa07a6431 ffff8800c9522000 ffffffffa077656e 00000000c0cc5616
   ffff8800c9522000 ffffffffa07a5e20 ffff880095e0c100 0000000000000000
   ffff880067ec7740 ffffffffa077a140 ffff880067ec7740 0000000000000016
  Call Trace:
   [<ffffffffa07a6431>] ? v4l_s_parm+0x21/0x50 [videodev]
   [<ffffffffa077656e>] ? vidioc_s_parm+0x4e/0x60 [gspca_main]
   [<ffffffffa07a5e20>] ? __video_do_ioctl+0x280/0x2f0 [videodev]
   [<ffffffffa07a5ba0>] ? video_ioctl2+0x20/0x20 [videodev]
   [<ffffffffa07a59b9>] ? video_usercopy+0x319/0x4e0 [videodev]
   [<ffffffff81182dc1>] ? page_add_new_anon_rmap+0x71/0xa0
   [<ffffffff811afb92>] ? mem_cgroup_commit_charge+0x52/0x90
   [<ffffffff81179b18>] ? handle_mm_fault+0xc18/0x1680
   [<ffffffffa07a15cc>] ? v4l2_ioctl+0xac/0xd0 [videodev]
   [<ffffffff811c846f>] ? do_vfs_ioctl+0x28f/0x480
   [<ffffffff811c86d4>] ? SyS_ioctl+0x74/0x80
   [<ffffffff8154a8b6>] ? entry_SYSCALL_64_fastpath+0x16/0x75
  Code: c7 93 d9 79 a0 5b 5d e9 f1 f3 9a e0 0f 1f 00 66 2e 0f 1f 84 00
    00 00 00 00 66 66 66 66 90 53 31 d2 48 89 fb 48 83 ec 08 8b 46 10 <f7>
    76 0c 80 bf ac 0c 00 00 00 88 87 4e 0e 00 00 74 09 80 bf 4f
  RIP  [<ffffffffa079bd62>] sd_set_streamparm+0x12/0x60 [gspca_ov534]
   RSP <ffff880095c4fce8>
  ---[ end trace 279710c2c6c72080 ]---

Following what the doc says about a zeroed timeperframe (see
http://www.linuxtv.org/downloads/v4l-dvb-apis/vidioc-g-parm.html):

  ...
  To reset manually applications can just set this field to zero.

fix the issue by resetting the frame rate to a default value in case of
an unusable timeperframe.

The fix is done in the subdrivers instead of gspca.c because only the
subdrivers have notion of a default frame rate to reset the camera to.
Signed-off-by: NAntonio Ospite <ao2@ao2.it>
Cc: stable@vger.kernel.org
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The current cx231xx driver doesn't work with bulk transfer mode.
This patch makes it possible to use bulk transfer mode.
Signed-off-by: NTerry Heo <terryheo@google.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

The radio_tea5777_ops structure is never modified, so declare it as const.

Done with the help of Coccinelle.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Move constants to the right of binary operators.

Generated by: scripts/coccinelle/misc/compare_const_fl.cocci

CC: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Vidioc-g-ext-ctrls can now be used to get the default value of the
controls.
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This driver does not use the control infrastructure.
Add support for the new field which on structure
 v4l2_ext_controls
Acked-by: NMike Isely <isely@pobox.com>
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

This driver does not use the control infrastructure.
Add support for the new field which on structure
 v4l2_ext_controls
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Support for new field which on v4l2_ext_controls, used to get the
default value of one or more controls.
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

Replace the obsolete field ctrl_class with "which".

Make sure it not used in future modules by commenting out the field with
ifndef __KERNEL_ .

The field cannot be simply removed because that would be change on the
kenel API to the userspace (and we don't like that).
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>

So it can be used to get the default value of a control.

Without this change it is not possible to get the
default value of array controls.
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>