- 14 5月, 2012 40 次提交
-
-
由 Mike Dunn 提交于
The ecc.read_page() method for nand drivers is changed to return the maximum number of bitflips that were corrected on any one region covering an ecc step, This patch doesn't change what the nand code returns to mtd. This v2 includes the change to the fsl_ifc_nand driver requested by Scott¹. ¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040883.htmlSigned-off-by: NMike Dunn <mikedunn@newsguy.com> Acked-by (freescale changes): Scott Wood <scottwood@freescale.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Mike Dunn 提交于
An element 'bitflip_threshold' is added to struct mtd_info, and also exposed as a read/write variable in sysfs. This will be used to determine whether or not mtd_read() returns -EUCLEAN or 0 (absent a hard error). If the driver leaves it as zero, mtd will set it to a default value of ecc_strength. This v2 adds the line that propagates bitflip_threshold from the master to the partitions - thanks Ivan¹. ¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040900.htmlSigned-off-by: NMike Dunn <mikedunn@newsguy.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Mike Dunn 提交于
ecc_strength element of struct mtd_info is exposed as a read-only variable in sysfs. Signed-off-by: NMike Dunn <mikedunn@newsguy.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Mike Dunn 提交于
This fixes a couple of ecc strength values for which I earlier made conservative guesses, but whose correct values were later determined¹ (thanks Ivan). Also sets strength for fsl_ifc_nand, which was merged to mainline after the original patch that set the strength for all drivers. ¹ http://lists.infradead.org/pipermail/linux-mtd/2012-March/040325.htmlSigned-off-by: NMike Dunn <mikedunn@newsguy.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Mike Dunn 提交于
ecc_strength element of mtd_info will be the strength of one ecc step, not of the entire writesize, as was previously planned. This is the appropriate way because, as was pointed out¹, bit errors in excess of the strength of one step can cause a hard error if they all occur within the same ecc region. ¹ http://lists.infradead.org/pipermail/linux-mtd/2012-March/040313.htmlSigned-off-by: NMike Dunn <mikedunn@newsguy.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Bastian Hecht 提交于
To make sure the NAND chip is properly programmed we need a status command before each page write. When CONFIG_MTD_NAND_VERIFY_WRITE=y this assumption is broken when writing multiple pages consecutively. This patch fixes this. Signed-off-by: NBastian Hecht <hechtb@gmail.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Xi Wang 提交于
Replace the verbose `je32_to_cpu(latest_node->csize)' with a shorter `csize'. Signed-off-by: NXi Wang <xi.wang@gmail.com> Cc: Artem Bityutskiy <dedekind1@gmail.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Xi Wang 提交于
`csize' is read from disk and thus needs validation. Otherwise a bogus value 0xffffffff would turn the subsequent kmalloc(csize + 1, ...) into kmalloc(0, ...), leading to out-of-bounds write. This patch limits `csize' to JFFS2_MAX_NAME_LEN, which is also used in jffs2_symlink(). Artem: we actually validate csize by checking CRC, so this 0xFFs cannot come from empty flash region. But I guess an attacker could feed JFFS2 an image with random csize value, including 0xFFs. Signed-off-by: NXi Wang <xi.wang@gmail.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Peter Meerwald 提交于
Signed-off-by: NPeter Meerwald <p.meerwald@bct-electronic.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Uwe Kleine-König 提交于
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Uwe Kleine-König 提交于
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Uwe Kleine-König 提交于
This is tested on i.MX27. Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Uwe Kleine-König 提交于
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Uwe Kleine-König 提交于
This gets rid of one more nfc_is_vX(). Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Uwe Kleine-König 提交于
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Uwe Kleine-König 提交于
This commit makes problems on v1 and v2 regarding 4KiBpages more obvious. As I don't have a 4KiB flash handy I just keep the status quo. Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Uwe Kleine-König 提交于
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Uwe Kleine-König 提交于
This prepares switching to platform ids and of-tree probing. Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Uwe Kleine-König 提交于
This gets rid of several instances of cpu_is_mx21() in the driver. Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Uwe Kleine-König 提交于
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Ryosuke Saito 提交于
page_read() never returns NULL, so we can remove the NULL check here. Signed-off-by: NRyosuke Saito <raitosyo@gmail.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Jonas Gorski 提交于
The original Broadcom partition order has the root fs in front of the kernel, which resulted in miscalculated partition sizes. Detect when such an image is on the flash and also reorder the partitions accordingly. Signed-off-by: NJonas Gorski <jonas.gorski@gmail.com> Acked-by: NFlorian Fainelli <florian@openwrt.org> Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Ivan Djelic 提交于
If a context switch occurs in function omap_wait() just before the while loop is entered, then upon return from context switch the timeout may already have elapsed: in that case, status is never read from NAND device, and omap_wait() returns an error. This failure has been experimentally observed during stress tests. This patch ensures a NAND status read is always performed before returning, as in the generic nand_wait() function. Signed-off-by: NIvan Djelic <ivan.djelic@parrot.com> Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Viresh Kumar 提交于
clk_{un}prepare is mandatory for platforms using common clock framework. Since this driver is used by SPEAr platform, which supports common clock framework, add clk_{un}prepare() support for it. Signed-off-by: NViresh Kumar <viresh.kumar@st.com> Acked-by: NLinus Walleij <linus.walleij@linaro.org> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Viresh Kumar 提交于
clk_{un}prepare is mandatory for platforms using common clock framework. Since this driver is used by SPEAr platform, which supports common clock framework, add clk_{un}prepare() support for it. Signed-off-by: NViresh Kumar <viresh.kumar@st.com> Acked-by: NLinus Walleij <linus.walleij@linaro.org> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Randy Dunlap 提交于
scb2_flash.c is a PCI driver, but its build fails when CONFIG_PCI is not enabled, so make it depend on PCI. drivers/mtd/maps/scb2_flash.c:237:1: warning: data definition has no type or storage class drivers/mtd/maps/scb2_flash.c:237:1: warning: type defaults to 'int' in declaration of 'module_pci_driver' drivers/mtd/maps/scb2_flash.c:237:1: warning: parameter names (without types) in function declaration Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Grazvydas Ignotas 提交于
If prefetch engine is busy, current code "forgets" to call dma_unmap_single(), which results in a deadlock later, so add it. Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Daniel Drake 提交于
Add a new rp_size= parameter which creates a "reserved pool" of disk space which can only be used by root. Other users are not permitted to write to disk when the available space is less than the pool size. Based on original code by Artem Bityutskiy in https://dev.laptop.org/ticket/5317 [dwmw2: use capable(CAP_SYS_RESOURCE) not uid/gid check, fix debug prints] Signed-off-by: NDaniel Drake <dsd@laptop.org> Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Huang Shijie 提交于
Some not-supported nand chips may pass the current parsing code, and get the wrong page size and oob size. Sometimes, it's hard to notice that you get the wrong values, because there is no warning or error. So it's useful to print out the page size and oob size in the end of the parsing function. We can check these values with the datasheet of the nand chip as soon as possible. Artem: amend the print a bit Signed-off-by: NHuang Shijie <b32955@freescale.com> Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Prabhakar Kushwaha 提交于
- Fix NAND_CMD_READID command for ONFI detect. - Add NAND_CMD_PARAM command to read the ONFI parameter page. Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com> Acked-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Jim Cromie 提交于
Signed-off-by: NJim Cromie <jim.cromie@gmail.com> Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Axel Lin 提交于
This patch converts the drivers in drivers/mtd/* to use module_pci_driver() macro which makes the code smaller and a bit simpler. Signed-off-by: NAxel Lin <axel.lin@gmail.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Huang Shijie 提交于
The mxs.h does not exit in the mx6q. So rewrite the __mxs_clrl()/__mxs_setl() and remove the mxs.h. Signed-off-by: NHuang Shijie <shijie8@gmail.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Uwe Kleine-König 提交于
As long as there is no other non-const variable marked __initdata in the same compilation unit it doesn't hurt. If there were one however compilation would fail with error: $variablename causes a section type conflict because a section containing const variables is marked read only and so cannot contain non-const variables. Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 H Hartley Sweeten 提交于
Use the default partition parser, cmdlinepart, provided by the plat_nand driver. Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 H Hartley Sweeten 提交于
Use the default partition parser, cmdlinepart, provided by the plat_nand driver. Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 H Hartley Sweeten 提交于
Use the default partition parser, cmdlinepart, provided by the plat_nand driver. Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 H Hartley Sweeten 提交于
Use the default partition parser, cmdlinepart, provided by the plat_nand driver. Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com> Acked-by: NTony Lindgren <tony@atomide.com> Acked-by: NAlexander Clouter <alex@digriz.org.uk> Acked-by: NMarek Vasut <marek.vasut@gmail.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 H Hartley Sweeten 提交于
Use cmdlinepart as the default partition parser and allow the arch setup code to still use their own partition parsers. Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
git://git.infradead.org/linux-mtd由 Linus Torvalds 提交于
Pull three MTD fixes from David Woodhouse: - Fix a lock ordering deadlock in JFFS2 - Fix an oops in the dataflash driver, triggered by a dummy call to test whether it has OTP functionality. - Fix request_mem_region() failure on amsdelta NAND driver. * tag 'for-linus-3.4-20120513' of git://git.infradead.org/linux-mtd: mtd: ams-delta: fix request_mem_region() failure jffs2: Fix lock acquisition order bug in gc path mtd: fix oops in dataflash driver
-