Tegra124 supports a block-linear mode in addition to the regular pitch
linear and tiled modes. Add support for these by moving the internal
representation into a structure rather than a simple flag.
Tested-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

A race condition currently exists on Tegra, where it can happen that a
monitor attached via HDMI isn't detected during the initial FB helper
setup, but the hotplug event happens too early to be processed by the
poll helpers because they haven't been initialized yet. This happens
because on some boards the HDMI driver can control the regulator that
supplies the +5V pin on the HDMI connector. Therefore depending on the
timing between the initialization of the HDMI driver and the rest of
DRM, it's possible that the monitor returns the hotplug signal right
within the window where we would miss it.

Unfortunately, drm_kms_helper_poll_init() will wreak havoc when called
before at least some parts of the FB helpers have been set up.

This commit fixes this by splitting out the minimum of initialization
required to make drm_kms_helper_poll_init() work into a separate
function that can be called early. It is then safe to move all of the
poll helper initialization to an earlier point in time (before the
HDMI output driver has a chance to enable the +5V supply). That way if
the hotplug signal is returned before the initial FB helper setup, the
monitor will be forcefully detected at that point, and if the hotplug
signal is returned after that it will be properly handled by the poll
helpers.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

To implement hotplug detection in a race-free manner, drivers must call
drm_kms_helper_poll_init() before hotplug events can be triggered. Such
events can be triggered right after any of the encoders or connectors
are initialized. At the same time, if the drm_fb_helper_hotplug_event()
helper is used by a driver, then the poll helper requires some parts of
the FB helper to be initialized to prevent a crash.

At the same time, drm_fb_helper_init() requires information that is not
necessarily available at such an early stage (number of CRTCs and
connectors), so it cannot be used yet.

Add a new helper, drm_fb_helper_prepare(), that initializes the bare
minimum needed to allow drm_kms_helper_poll_init() to execute and any
subsequent hotplug events to be processed properly.
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

There's no need for this to be modifiable. Make it const so that it can
be put into the .rodata section.
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

All drm_fb_helper_restore_fbdev_mode() call sites, save one, do the same
locking.  Simplify this into drm_fb_helper_restore_fbdev_mode_unlocked().
Signed-off-by: NRob Clark <robdclark@gmail.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If we don't have enough memory for ->planes then we leak "fb".
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NThierry Reding <treding@nvidia.com>

A lot of the modern userspace is capable of working without the legacy
fbdev support. kmscon can be used as a replacement for the framebuffer
console, and KMS X drivers create their own framebuffers.

Most people don't have a system where all of this works yet, though, so
leave support enabled by default.
Signed-off-by: NThierry Reding <treding@nvidia.com>

The fbdev screen memory pointer is annotated __iomem, so cast the kernel
virtual address to that address space to make the warning go away.
Signed-off-by: NThierry Reding <treding@nvidia.com>

The gr3d engine renders images bottom-up. Allow buffers that are used
for 3D content to be marked as such and implement support in the display
controller to present them properly.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NThierry Reding <treding@nvidia.com>

The gr2d and gr3d engines work more efficiently on buffers with a tiled
memory layout. Allow created buffers to be marked as tiled so that the
display controller can scan them out properly.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NThierry Reding <treding@nvidia.com>

In order to make subsystem-wide changes easier, move the Tegra DRM
driver back into the DRM tree.
Signed-off-by: NThierry Reding <treding@nvidia.com>

Most of the included files are either not required or already included
by some other header file.
Signed-off-by: NThierry Reding <treding@nvidia.com>

The host1x and Tegra DRM drivers are currently tightly coupled. Renaming
the structure marks the boundary more clearly.
Signed-off-by: NThierry Reding <treding@nvidia.com>

This patch introduces a memory manager for tegra drm and moves
existing parts to use it. As cma framebuffer helpers can no more
be used, this patch adds also a separate framebuffer driver for
tegra.
Signed-off-by: NArto Merilainen <amerilainen@nvidia.com>
Signed-off-by: NTerje Bergstrom <tbergstrom@nvidia.com>
Reviewed-by: NThierry Reding <thierry.reding@avionic-design.de>
Tested-by: NThierry Reding <thierry.reding@avionic-design.de>
Tested-by: NErik Faye-Lund <kusmabite@gmail.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Both host1x and drm drivers have host1x structures. This patch
renames the host1x structure under drm to follow name host1x_drm.
Signed-off-by: NArto Merilainen <amerilainen@nvidia.com>
Signed-off-by: NTerje Bergstrom <tbergstrom@nvidia.com>
Reviewed-by: NThierry Reding <thierry.reding@avionic-design.de>
Tested-by: NThierry Reding <thierry.reding@avionic-design.de>
Tested-by: NErik Faye-Lund <kusmabite@gmail.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Make drm part of host1x driver.
Signed-off-by: NArto Merilainen <amerilainen@nvidia.com>
Signed-off-by: NTerje Bergstrom <tbergstrom@nvidia.com>
Reviewed-by: NThierry Reding <thierry.reding@avionic-design.de>
Tested-by: NThierry Reding <thierry.reding@avionic-design.de>
Tested-by: NErik Faye-Lund <kusmabite@gmail.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

drm_fbdev_cma_init does the inital fbcon setup by calling down into
drm_fb_helper_initial_config, so no need at all to restore the just
set up configuration right away ...
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This commit adds a KMS driver for the Tegra20 SoC. This includes basic
support for host1x and the two display controllers found on the Tegra20
SoC. Each display controller can drive a separate RGB/LVDS output.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NMark Zhang <markz@nvidia.com>
Reviewed-by: NMark Zhang <markz@nvidia.com>
Tested-by: NMark Zhang <markz@nvidia.com>
Tested-and-acked-by: NAlexandre Courbot <acourbot@nvidia.com>
Acked-by: NTerje Bergstrom <tbergstrom@nvidia.com>
Tested-by: NTerje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>