After clear portsc.phcd, PHY needs 200us stable time for switch
32K clock to AHB clock.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We need this to keep PHY's power on or off during the system
suspend mode. If we need to enable USB wakeup, then we
must keep PHY's power being on during the system suspend mode.
Otherwise, we need to keep PHY's power being off to save power.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When we need the PHY can be waken up by external signals,
we can call this API. Besides, we call mxs_phy_disconnect_line
at this API to close the connection between USB PHY and
controller, after that, the line state from controller is SE0.
Once the PHY is out of power, without calling mxs_phy_disconnect_line,
there are unknown wakeups due to dp/dm floating at device mode.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

It is used to access un-regulator registers according to
different controllers.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Two PHY bugs are fixed by IC logic, but these bits are not
enabled by default, so we enable them at driver.
The two bugs are: MXS_PHY_ABNORMAL_IN_SUSPEND and MXS_PHY_SENDING_SOF_TOO_FAST
which are described at code.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Change "high speed" to "HS"
Change "non-high speed" to "FS/LS"

Implementation of notify_suspend and notify_resume will be different
according to mxs_phy_data->flags.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

It is needed by imx6 SoC series, but not for imx23 and imx28.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The auto setting is used to open related power and clocks
automatically after receiving wakeup signal.

With this feature, the PHY's clock and power can be recovered
correctly from low power mode, it is guaranteed by IC logic.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The mxs-phy has several bugs and features at different
versions, the driver code can get it through of_device_id.data.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We need to initialize the notifer before use it.

So lets initialize it when add a new phy device to
reduce the code redundancy.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Acked-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We need to set mxs_phy rather as the platform drvdata so that we can get
the correct mxs_phy in mxs_phy_remove().
Signed-off-by: NJisheng Zhang <jszhang@marvell.com>
Acked-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

stmp_reset_block() may fail, so let's check its return value and propagate it
in the case of error.
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

The mxs-phy is missing the phy.type property, why the usb_get_phy helper
function won't be able to find it. This patch adds this missing property.
Signed-off-by: NMichael Grzeschik <mgr@pengutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Commit 0998d063 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this will make sure that we have sensible names
for all phy drivers. Current situation was already
quite bad with too generic names being used.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

that's a much more reasonable location for
those drivers. It helps us saving drivers/usb/otg/
for when we actually start adding generic OTG
code.

Also completely delete drivers/usb/otg/ as there's
nothing left there.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch converts the mxs-phy driver from readl_relaxed(), writel_relaxed()
to the plain readl(), writel() functions, which are available on all platforms.

This is done to enable compile time testing on non ARM platforms.
Reported-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We now have usb_add_phy_dev(), so use it to register with the framework
to be able to find the phy from the USB driver.
Tested-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Reviewed-by: NKishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.

devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It needs to call set_suspend during USB suspend/resume
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc: Li Yang <leoli@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The old parameter "port" is useless for phy notify, as one usb
phy is only for one usb port. New parameter "speed" stands for
the device's speed which is on the port, this "speed" parameter
is needed at some platforms which will do some phy operations
according to device's speed.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Tested-by: NMike Thompson <mpthompson@gmail.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

As phy is working, re-init phy may cause unexpected results
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The real reason causes mx23 fail are:

- Calling mxs_phy_hw_init(mxs_phy) again at connection
- Error connect/disconnect nodity at hub.c

The coming patch will fix above two problems, Mike Thompson
tested his hardware works OK after commented out this delay
setting.

This reverts commit 363366cf.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently mx23 fails to enumerate a USB device:

[ 1.300000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1.520000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1.740000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 1.960000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 2.180000] hub 1-0:1.0: unable to enumerate USB device on port 1

Use a kernel workqueue to asynchronously delay the setting of
ENHOSTDISCONDETECT bit until after higher level hub connect/reset processing
is complete.  Prematurely setting the bit prevents the connection
processing from completing and not setting it prevents disconnect from being
detected. No delay is needed for clearing of ENHOSTDISCONDETECT.

Successfully tested on mx23-olinuxino (micro, mini and maxi variants) and mx28evk.

Cc: stable@vger.kernel.org # v3.6
Signed-off-by: NMike Thompson <mpthompson@gmail.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

mxs phy is used in Freescale i.MX SoCs, for example
imx23, imx28, imx6Q. This patch adds the basic host
support.
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Peter Chen <peter.chen@freescale.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NSubodh Nijsure <snijsure@grid-net.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>