Try to enable msi on chips that support it.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Spread spectrum is a periodic disturbance added
to the feedback divider to change the pixel clock
periodically to reduce interference.

Only enabled on LVDS.

v2: add support for r4xx and fix DCE 3
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The *_HIGH regs are reversed. The secondary ones are in the
primary block and vice versa.

We currently only use a 32 bit internal address, so these are
0 for now.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This patch only changes this is the swap path, where it doesn't loop.
Signed-off-by: NRobert Noland <rnoland@2hip.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- Reduce the chance of error and avoid a bit of overhead.
  - Use switch to assign color and format
Signed-off-by: NRobert Noland <rnoland@2hip.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Where supported use ulMinPixelClockPLL_Output rather than
usMinPixelClockPLL_Output for pll_out_min.  This seems to
improve pll selection on some boards.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

doesn't have a tv-out port
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The problem boils down to the order when the bit11
of the texture size is or'ed to the original width.
In the end each mipmap level has the same width or
height because of that 11 bit is ored to the scaled
down lod with and thus blows up the size again to the
full size or more due to the power of two rounding
afterwards.

The attached patch changes this order so that the
texture sizes are computed correct. Also the on error
the yet missing inputs to the size computation are
printed which helped me to find out where it really breaks.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This sets the fbcon to use TRUECOLOR by default, it then
only modifies the pseudo palette for fbcon, and only touches
the real palette when in 8-bit pseudo color mode.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Original radeon didn't have a connector table in the
bios.  Check for the CRT table and if we have one,
add a VGA connector.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Need to check the return type for the quirk function
to decide whether we add the connectors and encoders.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Sometimes we will get the incorrect display modeline when parsing the detailed
timing in EDID. For example:
   >hsync/vsync width is zero
   >sync is beyond the blank.

So add the basic check for the detailed timing in EDID to avoid the incorrect
display modeline.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMatt Turner <mattst88@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

fixes fdo bug 24496
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

D1MODE_INTERLEAVE_EN was getting set in some cases
in the encoder quirks function due to the changes in
5a9bcaccSigned-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Based partly on a patch from
Christian Koenig <deathsimple@vodafone.de>

- fix several memory leaks in radeon_connector->edid handling
- store edid in radeon_connector->edid in detect() or get_modes()
- switch hdmi detect code to use radeon_connector->edid
- add support for oem boards multiple connectors that share
a ddc line.
- short circuit lvds_detect() if have a stored edid
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- crtc 0 routing was wrong
- need to clear various timing bits in FP_GEN_CNTL
- need to set FP_H/V2_SYNC_STRT_WID regs for crtc 1
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

radeon_encoder->active_device defines the active routing
between the encoder and connector.  The encoder fixup and
dpms functions need to know the active_device to function
properly.  Setting active_device in the prepare hook was
too late in some cases.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

drm modes are objects with indentifiers.  Make sure to preserve
the mode id when copying mode params.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

With the adjust table introduction, we need to fill out index
before getting the table version.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This reverts commit 49c458e5. It
seems to have some side effects in the non-kms cases.
Signed-off-by: NDave Airlie <airlied@redhat.com>

In case the system has bad native mode info but
valid edid.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This reduces the number of mode format conversions needed
and makes native panel mode support cleaner.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- clean up tv timing handling
- unify SetCRTC_Timing and SetCRTC_UsingDTDTiming
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

DCE3+ has an AdjustDisplayPll that will adjust the pixel
clock accordingly based on the encoder/transmitter to
handle special hw requirements.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Based on recommendation from bios docs.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If the panel data is bogus this can lead to problems
later when the hardware trys to set the mode.  If the
data is invalid, report LVDS as disconnected.

Should fix fdo bug 24247.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

While investigating the cause of CRTC FIFO underruns, I noticed that when
converting the memory bandwidth calculation from the userspace X driver code,
an instance of '8.0' was apparently accidentally converted to '80'.
Signed-off-by: NMichel Dänzer <daenzer@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The hook may change the number of bytes per pixel being scanned out, which
affects the CRTC memory bandwidth requirements. E.g. booting in 8bpp and then
running X in 32bpp would result in the bandwidth requirements being
underestimated for the latter and consequently in CRTC FIFO underruns causing
visible artifacts with 3D intensive workloads.

ATOM changes only compile-tested.
Signed-off-by: NMichel Dänzer <daenzer@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The fb binding might be happening in a subsequent crtc setup call.

gets rid of some lut issues.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Both r100/r600 had this wrong, use the macro to extract the register
to relocate.
Signed-off-by: NDave Airlie <airlied@redhat.com>

There is no need to assign vb before you know that space is available.

[agd5f: adapted for kernel tree.]
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This is just a cleanup of the list macro usage.
Signed-off-by: NDave Airlie <airlied@redhat.com>

For AGP to work unmapped access must cover VRAM & AGP as
AGP is treated like VRAM by the GPU (ie physical address).
This patch properly setup the virtual memory system aperture
to cover AGP if AGP is enabled. It seems that there is memory
corruption after resume when using AGP (RV770 seems unaffected
thought). Version 2 just fix merge issue with updated AGP
fallback patch.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

When GPU acceleration is not working with AGP try to fallback to non
AGP GART (either PCI or PCIE GART). This should make KMS failure on
AGP less painfull. We still need to find out what is wrong when AGP
fails but at least user have a lot of more chances to get a working
configuration with acceleration. This patch also cleanup R600/RV770
fallback path so they use same code as others asics. Version 2
factorize agp disabling logic to avoid code duplication and bugs.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Bad generated header file leaded to use wrong register
to check IRQ status and acknowledge them. Fix the header
and use proper registers.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Duplicate bits set
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

the global refcount wasn't being increased after the first reference.
this caused an oops on unload on a multi-gpu card.
Signed-off-by: NDave Airlie <airlied@redhat.com>

The previous patches had some unwanted side effects, I've fixed
the lack of 32bpp working, and fixed up 16bpp so it should also work.

this also adds the interface to allow the driver to set a preferred
console depth so for example low memory rn50 can set it to 8bpp.
It also catches 24bpp on cards that can't do it and forces 32bpp.

Tested on r100/r600/i945.
Signed-off-by: NDave Airlie <airlied@redhat.com>