An errata workaround for omap24xx is not setting the buffering disable bit
25 what is the purpose but channel enable bit 7 instead.

Background for this fix is the DMA stalling issue with ASoC omap-mcbsp
driver. Peter Ujfalusi <peter.ujfalusi@nokia.com> has found an issue in
recording that the DMA stall could happen if there were a buffer overrun
detected by ALSA and the DMA was stopped and restarted due that. This
problem is known to occur on both OMAP2420 and OMAP3. It can recover on
OMAP3 after dma free, dma request and reconfiguration cycle. However, on
OMAP2420 it seems that only way to recover is a reset.

Problem was not visible before the commit c12abc01. That commit changed that
the McBSP transmitter/receiver is released from reset only when needed. That
is, only enabled McBSP transmitter without transmission was able to prevent
this DMA stall problem in receiving side and underlying problem did not show
up until now. McBSP transmitter itself seems to no be reason since DMA
stall does not recover by enabling the transmission after stall.

Debugging showed that there were a DMA write active during DMA stop time and
it never completed even when restarting the DMA. Experimenting showed that
the DMA buffering disable bit could be used to avoid stalling when using
source synchronized transfers. However that could have performance hit and
OMAP3 TRM states that buffering disable is not allowed for destination
synchronized transfers so subsequent patch will implement a method to
complete DMA writes when stopping.

This patch is based on assumtion that complete lock-up on OMAP2420 is
different but related problem. I don't have access to OMAP2420 errata but
I believe this old workaround here is put for a reason but unfortunately
a wrong bit was typed and problem showed up only now.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NManjunath Kondaiah G <manjugk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This is just a readability and debugging improvement. As selection bit in
DEVCONF register is cleared when using 96 MHz PRCM source and set when using
external CLKS pin, change definitions to be sync with these.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>

Reduce the amount of debugging generated by default when unused clocks
are being disabled by the clock code.  The previous code would only
generate debug-level messages, but some people who wished to run
production kernels with debug-level messages enabled reported that the
large number of clock disable messages were slowing boot.  Now to
enable clock-by-clock disable messages, DEBUG needs to be defined in
mach-omap2/clock.c.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Tuukka Tikkanen <tuukka.tikkanen@nokia.com>
Cc: Tim Bird <tim.bird@am.sony.com>

Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap.  This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.

In response, move the SCM headers into mach-omap2/.

As part of this, remove the direct SCM access from the OMAP UDC
driver.  It was clearly broken.  The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>

Split plat-omap/common.c into three pieces:

1. the 32KiHz sync timer and clocksource code, which now lives in
   plat-omap/counter_32k.c;

2. the OMAP2+ common code, which has been moved to mach-omap2/common.c;

3. and the remainder of the OMAP-wide common code, which includes the
   deprecated ATAGs code and a deprecated video RAM reservation function.

The primary motivation for doing this is to move the OMAP2+-specific parts
into an OMAP2+-specific file, so that build breakage related to the
System Control Module code can be resolved.

Benoît Cousson <b-cousson@ti.com> suggested a new filename and found
some bugs in the counter_32k.c comments - thanks Benoît.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

Previously the OMAP McBSP ASoC driver implemented CLKS switching by
using omap_ctrl_{read,write}l() directly.  This is against policy; the OMAP
System Control Module functions are not intended to be exported to drivers.
These symbols are no longer exported, so as a result, the OMAP McBSP ASoC
driver does not build as a module.

Resolve the CLKS clock changing portion of this problem by creating a
clock parent changing function that lives in
arch/arm/mach-omap2/mcbsp.c, and modify the ASoC driver to use it.
Due to the unfortunate way that McBSP support is implemented in ASoC
and the OMAP tree, this symbol must be exported for use by
sound/soc/omap/omap-mcbsp.c.

Going forward, the McBSP device driver should be moved from
arch/arm/*omap* into drivers/ or sound/soc/* and the CPU DAI driver
should be implemented as a platform_driver as many other ASoC CPU DAI
drivers are.  These two steps should resolve many of the layering
problems, which will rapidly reappear during a McBSP hwmod/PM runtime
conversions.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Acked-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The OMAP ASoC McBSP code implemented CLKR and FSR signal muxing via
direct System Control Module writes on OMAP2+.  This required the
omap_ctrl_{read,write}l() functions to be exported, which is against
policy: the only code that should call those functions directly is
OMAP core code, not device drivers.  omap_ctrl_{read,write}*() are no
longer exported, so the driver no longer builds as a module.

Fix the pinmuxing part of the problem by removing calls to
omap_ctrl_{read,write}l() from the OMAP ASoC McBSP code and
implementing signal muxing functions in arch/arm/mach-omap2/mcbsp.c.
Due to the unfortunate way that McBSP support is implemented in ASoC
and the OMAP tree, these symbols must be exported for use by
sound/soc/omap/omap-mcbsp.c.

Going forward, the McBSP device driver should be moved from
arch/arm/*omap* into drivers/ or sound/soc/*, and the CPU DAI driver
should be implemented as a platform_driver as many other ASoC CPU DAI
drivers are.  These two steps should resolve many of the layering
problems, which will rapidly reappear during a McBSP hwmod/PM runtime
conversion.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Acked-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NLiam Girdwood <lrg@slimlogic.co.uk>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Conform the OMAP2420_CTRL_BASE macro name to the standard of the rest of the
OMAP*_CTRL_BASE macro names.  This fixes a bug in the OMAP2420 SCM code that
prevented OMAP242X_CTRL_REGADDR from working.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Some modules which have 16bit registers can cause imprecise
aborts if a __raw_readl/writel is used to read/write 32 bits.

Add an additional flag to identify modules which have such
hard requirement, and handle it in the hwmod framework.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Tested-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The OMAP3 IGEP module is a low-power, high performance production-ready
system-on-module (SOM) based on TI's OMAP3 family. More about this
board at www.igep.es.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
[tony@atomide.com: updated for the mmc changes and to be selected by default]
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes sparse warnings due non declarations of static functions.

arch/arm/plat-omap/sram.c:130:13: warning: symbol 'omap_detect_sram' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:216:13: warning: symbol 'omap_map_sram' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:450:12: warning: symbol 'omap_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:348:12: warning: symbol 'omap242x_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:369:12: warning: symbol 'omap243x_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:425:12: warning: symbol 'omap34xx_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:441:12: warning: symbol 'omap44xx_sram_init' was not declared. Should it be static

arch/arm/plat-omap/mcbsp.c:36:6: warning: symbol 'omap_mcbsp_write' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:50:5: warning: symbol 'omap_mcbsp_read' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:65:6: warning: symbol 'omap_mcbsp_st_write' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:70:5: warning: symbol 'omap_mcbsp_st_read' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:1648:15: warning: symbol 'omap_st_add' was not declared. Should it be static?

arch/arm/plat-omap/fb.c:414:15: warning: symbol 'omapfb_reserve_sram' was not declared. Should it be static?
arch/arm/plat-omap/cpu-omap.c:43:5: warning: symbol 'omap_verify_speed' was not declared. Should it be static?
arch/arm/plat-omap/cpu-omap.c:61:14: warning: symbol 'omap_getspeed' was not declared. Should it be static?
Signed-off-by: NManjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes sparse warnings due non declarations of static functions.

arch/arm/mach-omap2/timer-gp.c:115:12: warning: symbol 'omap2_gp_clockevent_set_gptimer' was not declared. Should it be static?
arch/arm/mach-omap2/powerdomain.c:993:5: warning: symbol 'pwrdm_set_lowpwrstchange' was not declared. Should it be static?
arch/arm/mach-omap2/board-flash.c:141:8: warning: symbol 'board_nand_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:416:6: warning: symbol 'n8x0_mmc_slot1_cover_handler' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:544:13: warning: symbol 'n8x0_mmc_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:902:13: warning: symbol 'rx51_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-video.c:107:13: warning: symbol 'rx51_video_mem_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-debugboard.c:155:12: warning: symbol 'zoom_debugboard_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-peripherals.c:280:13: warning: symbol 'zoom_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-igep0020.c:110:13: warning: symbol 'igep2_flash_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:109:6: warning: symbol 'am3517_evm_ethernet_init' was not declared. Should it be static?
drivers/mtd/onenand/omap2.c:577:5: warning: symbol 'omap2_onenand_rephase' was not declared. Should it be static?
Signed-off-by: NManjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes sparse warnings due to non declaration of
static structures and variables.

Sparse warning logs fixed:
arch/arm/mach-omap2/control.c:88:6: warning: symbol 'omap3_secure_ram_storage' was not declared. Should it be static?
n
arch/arm/mach-omap2/timer-gp.c:50:22: warning: symbol 'gptimer_wakeup' was not declared. Should it be static?
arch/arm/mach-omap2/timer-gp.c:240:18: warning: symbol 'omap_timer' was not declared. Should it be static?
arch/arm/mach-omap2/prcm.c:121:24: warning: symbol 'prcm_context' was not declared. Should it be static?
arch/arm/mach-omap2/mux2420.c:510:29: warning: symbol 'omap2420_pop_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux2430.c:589:29: warning: symbol 'omap2430_pop_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:934:28: warning: symbol 'omap3_cus_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1080:29: warning: symbol 'omap3_cus_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1272:28: warning: symbol 'omap3_cbb_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1393:29: warning: symbol 'omap3_cbb_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1603:28: warning: symbol 'omap36xx_cbp_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1821:29: warning: symbol 'omap36xx_cbp_ball' was not declared. Should it be static?
arch/arm/mach-omap2/pm-debug.c:165:15: warning: symbol 'pm_dbg_dir' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3evm.c:587:30: warning: symbol 'ads7846_config' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3evm.c:606:23: warning: symbol 'omap3evm_spi_board_info' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-sdram.c:46:25: warning: symbol 'rx51_sdrc_params' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-sdram.c:211:25: warning: symbol 'rx51_get_sdram_timings' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3touchbook.c:64:15: warning: symbol 'touchbook_revision' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:350:24: warning: symbol 'am3517_evm_dss_device' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3stalker.c:567:23: warning: symbol 'omap3stalker_spi_board_info' was not declared. Should it be static?
Signed-off-by: NManjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

A patch from Sukumar Ghorai <s-ghorai@ti.com> changed the
nwires to use caps instead. However, nwires is still
needed for the earlier controller.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Acked-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NMing Lei <tom.leiming@gmail.com>

In OMAP4, as per new PM programming model, the legacy registers
which were there in OMAP3 are all shifted by 0x100 while new one's
are added from offset 0 to 0x10.
For OMAP4, the register offset appending of 0x100 done in devices.c
currently, is moved to driver file.This change fits in for current
implementation as well as once the driver undergoes hwmod adaptation.

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The omap4 es2 hsmmc has a updated soft reset logic.After the
reset is issued monitor a 0->1 transition first. The reset of
CMD or DATA lines is complete only after a 0->1->0 transition
of SRC or SRD bits.
Signed-off-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Tested-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The existing definitions for cpu revision used
upper nibble in the bits[15:08]. With OMAP3630,
definitions use lower nibble.

This patch unifies the definitions to start
at lower nibble.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds driver support for OMAP2/3/4 high speed UART.

The driver is made separate from 8250 driver as we cannot
over load 8250 driver with omap platform specific configuration for
features like DMA, it makes easier to implement features like DMA and
hardware flow control and software flow control configuration with
this driver as required for the omap-platform.
This patch involves only the core driver and its dependent.

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Remove set_uart_globals function as this will not be needed as
physical address for uarts will be taken from hwmod data file.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch adds omap_hwmod data for UARTs on OMAP2 and OMAP3
platforms.

UART4 support for 3630 and OMAP2 hwmod data added by Govindraj R.
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

This patch splits omap_init_wdt() into separate omap_init_wdt()
functions under mach-omap1 and mach-omap2 and set them up with
subsys_initcall.

Also it uses  omap_device_build() API instead of
platform_device_register() for watchdog timer device registration
for OMAP2plus chips.

For OMAP2plus chips, the device specific data defined in centralized
hwmod database will be used.
Signed-off-by: NCharulatha V <charu@ti.com>
Acked-by: NCousson, Benoit <b-cousson@ti.com>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

Introduce of a generic way to setup smsc911x based Ethernet
controller connected to GPMC similar to gpmc-smc91x but without
timing setup.
Signed-off-by: NTim Nordell <tim.nordell@logicpd.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adding support for LogicPD's OMAP 3530 LV SOM and
OMAP 35x Torpedo board.
Signed-off-by: NTim Nordell <tim.nordell@logicpd.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add basic suppot, enable uart and led.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch has multiple fixes together. To ensure that git bisect work across
commits, all changes are clubbed together

1. Move the common control base address to control core
2. Remove the manually coeded defines and use the ones from headers.
3. Fix the the status register define in id.c for OMAP4
4. Fix all the register define in hsmmc.c
5. Use the control pad accessor API for omap4 hsmmc register accesses
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

On OMAP4, control module is divided into 4 separate IPs
- OMAP44XX_CTRL_MODULE_CORE
- OMAP44XX_CTRL_MODULE_PAD_CORE
- OMAP44XX_CTRL_MODULE_WKUP
- OMAP44XX_CTRL_MODULE_PAD_WKUP

This patch adds all the omap4 control module register data and
includes them in the common control.h

The register data is autogenerated from the codebase thanks
to Benoit Cousson efforts
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

On OMAP4 control pad are not addressable from control
core base. So the common omap_ctrl_read/write APIs breaks
Hence export separate APIs to manage the omap4 pad control
registers.

This APIs will work only for OMAP4
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

On omap4 control module is divided in four IP blocks.
- CTRL_MODULE_CORE			0x4a002000
- CTRL_MODULE_PAD_CORE		0x4a100000
- CTRL_MODULE_WKUP			0x4a30c000
- CTRL_MODULE_PAD_WKUP		0x4a31e000

Addressing all the modules with single base address is not possible
considering 16 bit offsets. The mux code manages the pad core and pad
wakeup related base address inside the mux framework. For other usage
only control core and control pad bases are necessary. So this patch
maps only needed pad control base address which is used by device drivers
and infrastructure code

The main control core base is still kept same in this patch to
keep git-bisect working. This will be fixed in the relevant patch
in this series.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

DSS on ES2 supports only OSWR, hence remove the support
for CSWR from the powerdomain framework.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBenoît Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>

update OMAP Kconfig help texts for all supported SoC models
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

McBSP SRG (Sample Rate Generator) and FSG (Frame Sync
Generator) is only needed to be enabled, when McBSP
is master.
In McBSP slave mode, the SRG, and FSG can be kept disabled,
which might save some power at the end in this configuration.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Added defines to avoid compilation error.
Signed-off-by: NSubramaniam C.A <subramaniam.ca@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix this and similar build warnings when building with
omap_4430sdp_defconfig.

 CC      arch/arm/mach-omap2/board-4430sdp.o
In file included from arch/arm/mach-omap2/board-4430sdp.c:36:
arch/arm/plat-omap/include/plat/usb.h:109: warning: return type defaults to 'int'
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Currently there is a bug in the existing omap_device core code when
extracting the hwmod structures passed to omap_device_build_ss(). This bug
gets exposed only when passing multiple hwmod structures to
omap_device_build_ss() resulting in incorrect extraction from second hwmod
structure.

This fix uses the pointer to pointer to omap_hwmod structure (array of
pointers to omap_hwmod structure) passed to omap_device_build_ss() to
correctly extract the appropriate omap_hwmod structure.

This patch has been created and tested on lo/master and mainline.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Acked-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Cc: Charulatha V <charu@ti.com>
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>

This patch is temporary fix to below crash. This is observed when
CPU is clocked more than 600 MHz.

Unhandled fault: imprecise external abort (0x1406) at 0xbf9ef65c
Internal error: : 1406 [#1] PREEMPT SMP
last sysfs file:
Modules linked in:
CPU: 0    Not tainted  (2.6.36-rc3+ #18)
PC is at kernel_thread_helper+0x0/0x14
LR is at kernel_thread_helper+0x0/0x14
pc : [<c003ce14>]    lr : [<c003ce14>]    psr: 00000093
sp : dc83bff8  ip : 00000000  fp : 00000000
r10: 00000000  r9 : 00000000  r8 : 00000000
r7 : 00000013  r6 : c003ce28  r5 : c008935c  r4 : 00000000
r3 : 00000000  r2 : 00000000  r1 : 00000000  r0 : 00000000
Flags: nzcv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c53c7f  Table: 8000404a  DAC: 00000017
Process swapper (pid: 2, stack limit = 0xdc83a2f0)
Stack: (0xdc83bff8 to 0xdc83c000)
bfe0: 00000000 ffffffff
[<c003ce14>] (kernel_thread_helper+0x0/0x14) from [<fffffffe>] (0xfffffffe)
Code: c03a0ba3 c03a5fcb c045c880 c0394035 (eb017701)
---[ end trace 1b75b31a2719ed1c ]---

The timer hwmod adaptation will eventually fix it in a proper way.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

Add support for use of DEBUG_LL for use with PandaBoard.
Signed-off-by: NDavid Anders <x0132446@ti.com>

This patch updates the id.c and cpu.h files to support
omap4 ES2.0 silicon detection. Few initial omap4 es2 samples
IDCODE is same as es1. So the patch uses ARM cpuid register to
detect the ES version for such samples
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

On OMAP4 there is no need to have SRAM_BOOTLOADER_SZ provision

Hence put this macro under CONFIG_ARCH_OMAP2PLUS check
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Reviewed-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>

For OMAP24xx/34xx/44xx: omap_type() returns the correct type:
 OMAP2_DEVICE_TYPE_TEST
 OMAP2_DEVICE_TYPE_EMU
 OMAP2_DEVICE_TYPE_SEC
 OMAP2_DEVICE_TYPE_GP
 OMAP2_DEVICE_TYPE_BAD

In current implementation there are two problems:
Problem 1:
For 34xx, the current if check will never return true.

Problem 2:
For 24xx the correct type check should be with omap_type() function
Verified by checking the TRM 24xx for CONTROL_STATUS register bits
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>