Both DVC/MIX have Volume Ramp Control. This patch supprts MIX
Volume Ramp. One note is that main purpose of MIX Volume Ramp
is to reduce noise, thus, MIX Ramp range is very few if you
compare to DVC Volume Ramp (DVC = 5bit, MIX = 4bit).

You can use MIX Volume Ranp like below
	amixer set "MIX Ramp Up Rate"   "0.125 dB/1 step"
	amixer set "MIX Ramp Down Rate" "0.125 dB/1 step"
	amixer set "MIX Ramp" on
	aplay xxx.wav &
	amixer set "MIX",0  80%  // DAI0 Volume Down
	amixer set "MIX",1 100%  // DAI1 Volume Up
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NHiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

DVC is supporting Volume Ramp Rate, and MIX has Volume Ramp
but not yet supported. To support MIX Volume Ramp, we want to
share Rate List since DVC/MIX are using almost same list.
This patch move DVC specific Volume Ramp Rate List to core.c.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NHiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

SSI is using rsnd_ssi_flags_xxx() macro to control flags.
But it is useful macro not only for SSI. This patch replace it
to more generic rsnd_flags_xxx().
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NHiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd kctrl is using both .private_value (for rsnd_kctrl_cfg)
and .private_data (for rsnd_mod) on snd_kcontrol.
But only 1 private data (= rsnd_kctrl_cfg) can be enough if it has
rsnd_mod pointer.
This patch doesn't use private_value.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch fixes this WARNING

sound/soc/sh/rcar/ssi.c:285:5-14: WARNING: Unsigned expression\
	compared with zero: main_rate < 0
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current Renesas sound driver is assuming that all Sampling rate and
channles are possible to use, but these are depends on inputed clock
and SSI connection situation.
For example, if it is using 1 SSI, enabled TDM mode and has 12288000
input clock, 2ch output can support until 192000Hz, but 6ch output can
support until 64000Hz, 8ch can support 48000Hz.
To control these situation correctly, it needs to support
hw_constraints / refine feature.

To support such feature, this patch adds new
rsnd_soc_hw_rule/constraint() which adds hw rule of Channel and
Sampling Rate.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NHiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current Renesas sound driver is assuming that all Sampling rate and
channles are possible to use, but these are depends on inputed clock
and SSI connection situation.
For example, if it is using 1 SSI, enabled TDM mode and has 12288000
input clock, 2ch output can support until 192000Hz, but 6ch output can
support until 64000Hz, 8ch can support 48000Hz.
To control these situation correctly, it needs to support
hw_constraints / refine feature.

To support such feature, this patch adds new rsnd_ssi_clk_query().
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NHiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current Renesas sound driver is assuming that all Sampling rate and
channles are possible to use, but these are depends on inputed clock
and SSI connection situation.
For example, if it is using 1 SSI, enabled TDM mode and has 12288000
input clock, 2ch output can support until 192000Hz, but 6ch output can
support until 64000Hz, 8ch can support 48000Hz.
To control these situation correctly, it needs to support
hw_constraints / refine feature.

To support such feature, it needs SSI clock query feature, and it needs
ADG clock query feature. Current ADG has rsnd_adg_ssi_clk_try_start()
and it is doing similar things, but it try to setup ADG register in
same time. This is not needed.

This patch adds new rsnd_adg_clk_query() and separates query feature
and register setting feature in adg.c
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NHiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current Renesas sound driver has slots and slots_num in
struct rsnd_dai, but these are very un-understandable naming
(It had named from TDM slots).
In this driver, the "slots" means total usable channels, and
"stot_num" means SSI lane number if Multi SSI was used.
To more understandable code, this patch renames "slots" to
"max_channels", and "slots_num" to "ssi_lane", and replaces related
functions name.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NHiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current SRC/DVC/CTU adds kctrl for each device,
and SRC can adjust its sampling rate during playback,
thus, this feature should be enabled only *during* playback.
This patch controls it more clearly
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd driver is sharing pointer related code between
PIO / DMA. But, it is used only PIO mode now, no longer needed.
This patch cleanup these.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd driver updates pointer when DMA transfer was finished
in DMA transfer mode. But PulseAudio requests more accurate
pointer update when timer mode.
This patch consider about DMA transfer residue and update more
accurate pointer.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

commit 2ea2cc86 ("ASoC: rsnd: remove struct rcar_snd_info")
removed all struct rsnd_dai_path_info related code.
This patch removes unused rsnd_dai_path_info.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Renesas R-Car Gen3 can output HDMI sound if SSIU/SSI are connected to
R-Car built-in HDMI device (R-Car Gen3 built-in HDMI device will be
controlled by DRM/KMS driver).
If SSIx was connected to HDMI0/1 on DT, SSI driver will detect it
automatically by this patch.
Note is that now Renesas R-Car sound driver is assuming that it is
using OF-graph base simple card for HDMI sound.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

To enable OF-graph base DT on rsnd driver, and to keep compatible
previous normal sound card style, it need to support both
"rcar_sound,dai" and "ports" (or "port") on DT.

This patch modify rsnd_dai_of_node() to parse
"rcar_sound,dai" and "ports" (or "port") as phase 1. It can detect
graph base style, but do nothing at this point.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current SSI uses PDTA bit which indicates data that Input/Output
data are Right-Aligned. But, 24bit sound should be Left-Aligned
in this HW. Because Linux is using Right-Aligned data, and HW uses
Left-Aligned data, current 24bit data is missing lower 8bit.
To fix this issue, this patch removes PDTA bit, and shift 8bit
in necessary module
Reported-by: NHiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NHiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

rsnd_mod_make_sure() will be used any situation,
thus, under DEBUG is not realistic.
This patch move it to non DEBUG area
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd driver is using rsnd_kctrl_new_m/s/e function,
but the differences are very few.
This patch merge these rsnd_kctrl_new_m/s/e into rsnd_kctrl_new
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NHiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rcar driver is trying to remove kctrl when remove time.
But, 1) rcar driver can't/shouldn't remove before removing sound
card driver, 2) sound card driver will call snd_ctl_dev_free()
and removes all kctrls by snd_ctl_remove().
Thus, rsnd_kctrl_remove() is not necessary. Current implementation
will get Oops when removing rcar driver after sound card.
This patch fix this issue.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

commit 5f222a29 ("ASoC: rsnd: use for_each_rsnd_mod_xxx() ...")
modifies rsnd_dai_call() to use for_each_rsnd_mod_arrays().

Current rsnd is incrementing iterator in rsnd_mod_next(),
but the iterator will indicate +1 position in for_each loop in
this case. Incremental position should be inside for()
Reported-by: NHoan Nguyen An <na-hoan@jinso.co.jp>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

commit 5f222a29 ("ASoC: rsnd: use for_each_rsnd_mod_xxx() ...")
modifies rsnd_dai_call() to use for_each_rsnd_mod_arrays().

Current rsnd is incrementing iterator in rsnd_mod_next(),
but the iterator will indicate +1 position in for_each loop in
this case. Incremental position should be inside for()
Reported-by: NHoan Nguyen An <na-hoan@jinso.co.jp>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd driver enables ADG clock when .probe timing,
but it breaks sound after Suspend/Resume. These should be setups
every suspend/resume timing too.
This patch is tested on R-Car Gen3 Salvator-X board
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NGaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

SSIU was controlled by SSI before, but
commit c7f69ab5("ASoC: rsnd: use mod base common method on SSIU")
separated it into ssiu.c

But, it didn't care about rsnd_get_dalign() for judging SSI_BUSIF_DALIGN
register value which changes the stream data order.
This function will be called from cmd/src/ssiu now, but current code
still cares ssi, not ssiu.
This patch fix it up
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NHiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current register name of "SSICKR" was came from R-Car Gen1
which is very old style. It is called as "BRGCKR" on R-Car Gen2/Gen3.
Let's rename it
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Renesas sound SSIU has SSI_SYS_STATUS register whick will
be changed if over/under run was occurred.
Current rsnd driver is handling over/under run error on SSI/SRC,
but doesn't on SSIU.
HW guys can't guarantee correct behavior if it already had error bit
on status register when it start.
Thus, it should be cleared every start timing. This patch do it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

R-Car Gen1 didn't have SSIU IP, and it was part of SRU.
In Gen2, SSIU was created and it has original register.
Let's cleanup rsnd_reg for SSIU, because this driver
doesn't support Gen1 SRU any more.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Gen1 support had been removed. "Gen2 only" comment is
no longer needed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current Renesas Sound driver requests DMA channel when .probe timing,
and release it when .remove timing. And use DMA on .start/.stop
But, Audio DMAC power ON was handled when request timing (= .probe),
and power OFF was when release timing (= .remove).
This means Audio DMAC power is always ON during driver was enabled.
To fixup this issue, it should request/release DMA channel on each
playback/recorde timing.
But, DMA channel request/release function uses mutex lock inside.
This means it will breaks current spinlock's interrupt protect.
To solve this issue, DMA channel request/release function needs to
be called from non-spinlock area. This patch adds its callback.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

DMA mod is now connected to stream via rsnd_dai_connect().
This means DMA mod can use .remove for its clearance.
rsnd_dma_detach() is no longer needed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current Renesas Sound driver is based on DeviceTree, and no one is
using this driver from non DT. Non-DT support is no longer needed.
Let's remove it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd driver is using too complex macro for for-loop of each mod.
In order to simplify this issue, this patch adds new rsnd_mod_next()
which is non-macro.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

commit 1a5658c2 ("ASoC: rsnd: count .probe/.remove for
rsnd_mod_call()") solved multi-resource-free issue, by putting
.probe/.remove under count control. But,it breaks sound mixing case
(if it was used under DPCM). In such case, it uses MIXn/DVCn/SSIn,
and these should be always probed.
This patch reverted above patch, and solved the same issue by
modifing _rsnd_kctrl_remove() function.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd_mod_call is counting its calling count to avoid unbalanced
function pair calling for error cases (ex init <-> quit).
SSI parent is now controlled as "mod" on current rsnd driver. Because of
this reason, SSI .remove function will be called twice if it was used as
SSI parent when user tried unbind. But probe/remove pair were not
counted. This patch counts probe/remove functions to avoid it.
Special thans Hiep
Reported-by: NHiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

SRC has Sync/Async mode, and it can't use Sync mode when Capture
with CMD. In Async mode, it needs to care about in/out SRC rate
for settings, but current driver supporting Playback case only.
This patch supports Capture case.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

SRC will convert rate, and then, CMD and SSI want to know its
rate (= SRC.in / SRC.out) for each purpose.
Current driver is supporting only Playback, but SRC+Capture support
needs more flexibility.
This patch adds rsnd_src_get_in/out_rate() for it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current SSI is supporting Normal SSI/Multi mode SSI/TDM mode SSI
and its behavior is based on input channels.
This input channel might be converted by CTU,
and SSI needs to be Multi SSI mode / TDM SSI mode if 6ch input

EX) 6ch input, CTU for 2ch, playback

 6ch    6ch    2ch    2ch    2ch     2ch
 -> SRC -> CTU -> MIX -> DVC -> SSIU -> SSI

EX) 6ch input, no CTU, Multi SSI, playback

 6ch    6ch    6ch    6ch    6ch     2ch
 -> SRC -> CTU -> MIX -> DVC -> SSIU -> SSI0/SSI1/SSI2

Current driver is using rsnd_get_adinr_chan() / rsnd_get_slot_width()
for this purpose, but it is complicated enough without meaning.
This patch adds new rsnd_runtime_channel_xxx() which is caring
CTU/Multi SSI.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch adds Renesas R-Car sound CTU (= Channel Transfer Unit)
very basic support, but not yet enough feature at this point.
Because CTU support needs more complex channel function for
each modules.
To avoid complex patch reviewing, this patch picked up very basic
part only.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Some R-Car sound requests picky register access which needs *force*
register write.
Some status register needs to set 1 to clear status, but we might
read 1 from its register. In such case, current regmap does nothing
and driver will be forever loop
To reduce code complexity, this patch uses regmap _force_
function for all register access.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd supports multi SSI (maximum 4 SSI for 8ch),
and, it should determine whether using each SSI or not in runtime.
Current judgement is vague, and had broken by
c308abe4("ASoC: rsnd: rsnd_ssi_is_multi_slave() macro uses
rsnd_ssi_multi_slaves()")
This patch makes clean it, and solve this issue.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>