with BIOS probing only we offer a non functional headphone swith and
volume slider.
Signed-off-by: NGuido Günther <agx@sigxcpu.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix this build error when CONFIG_PM is not set:
ound/pci/hda/hda_intel.c: In function 'azx_bus_reset':
sound/pci/hda/hda_intel.c:1270: error: implicit declaration of function 'snd_pcm_suspend_all'
sound/pci/hda/hda_intel.c:1271: error: implicit declaration of function 'snd_hda_suspend'
sound/pci/hda/hda_intel.c:1272: error: implicit declaration of function 'snd_hda_resume'
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Enable all three capture channels, including the missing nid 7 which is
the only one capable of capturing DMIC input

Enable Headphone amp for the HP jack. This causes a volume boost for
headphones, but does not cause any noticeable effect for light loads
like other amps, so there is no need to make it configurable.

Add Input Mix capture mux setting to capture the output of the playback
input mux (that is, what goes out the speakers except for PCM)

Hack another coef register because the stereo DMIC for some reason
produces a nonstandard sum/difference signal. I found a bit to make it
just use the sum signal for both channels, which makes it behave like a
standard mono microphone. The stereo is useless anyway (they're 1cm apart).

Tested working: Three capture channels, mic in, line in, DMIC.

Tested not working: CD. Not sure why, might be unconnected in the actual
hardware or a CD drive issue.

Also looked at SPDIF. It appears to work (emitter lights up inside the
HP out jack) but I lack a proper miniTOSLINK cable to test it.
Signed-off-by: NHector Martin <hector@marcansoft.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Short story: this laptop has 5.1 built-in speakers which you *really*
want to use (the not-so-"sub" woofer is what makes the audio above
average for a laptop), so 6-channel support is important (plus a decent
asound.conf to upmix stereo). It also has the 3 typical jacks that ought
to have a selectable mode. And it's based on ALC889, which sucks.

Rationale/explanations:

The const_channel_count stuff was added because, for a laptop like this,
you always have 6 channels available (internal speakers) but still need
to set the mode for the 3 external jacks. Therefore, the device always
needs to be in 6-channel mode but there still needs to be a mixer
control for the jack mode. You could use line/mic-in at the same time as
the 6 internal speakers, for example. You might be tempted to make it
even smarter by dynamically switching the max channel count when
headphones are plugged in (therefore muting the internal speakers and
reducing the physical channel count to the jack channel mode), but as a
user I consider this to be harmful because I want the audio to blow up
to 6 channels / upmixed as soon as I unplug the headphones, and having
opened the device while in 2-channel mode would prevent this from
working (and always making 6-channel mode available doesn't do any harm).

The hardware needs EAPD turned on and the DACs routed to the internal
speaker pins, so the patch adds those verbs.

The ALC889 CLFE and subsequent (side/aux, here unused) DACs do NOT work
by default, at least here. I wasted much time trying to talk to
Realtek/pshou about this, but they just kept sending me useless updates
to patch_realtek.c that did nothing relevant. In the end I gave up and
brute forced the issue by trying to flip every bit in the proprietary
coefficient registers, and eventually found the two magic registers that
need to be cleared to enable all DACs. I have only heard Acer users
complain, but that might be because ALC889 is pretty new and using 5.1
(and noticing the missing center/lfe channels) might not be that common.
If this is a generalized issue with all ALC889 systems then those verbs
should probably be moved to a common verb array.

The internal mic is untested and probably doesn't work.

These settings will probably work for other Acer Gemstone laptops with
the same 5.1 speaker config. When identified, those should be added to
the PCI subsystem ID list.
Signed-off-by: NHector Martin <hector@marcansoft.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The reset of a BUS controller during operations is somehow risky and
shouldn't be done inevitably for devices that have apparently no such
codec-communication problems.

This patch adds the check of the hardware and limits the bus-reset
capability.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some machines machine cause a severe CORB/RIRB stall in certain
weird conditions, such as PA access at the start up together with
fglrx driver.  This seems unable to be recovered without the controller
reset.

This patch allows the bus controller reset at critical errors so
that the communication gets recovered again.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Rearrange alc268_cfg_tbl[] in the order of vendor id, and group some
entries using SND_PCI_QUIRK_MASK().
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Currently, LG R510 is only able to produce sound on headphones, the
internal speakers are not working.

The user tested and confirmed that with model=Dell headphones,
internal speakers and the microphone are working flawlessly.
Tested-by: NSerdar Soytetir <tulliana@gmail.com>
Signed-off-by: NOzan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

this is a patch against current snapshot that adds:
6 channels support for the MB5 model
Signed-off-by: NKacper Szczesniak <kacper@qwe.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix issues for 3 generations of HP workstations.

The modest modifications do the following:
1. Change the second MIC from device 3 to device 1
2. Init the "boost" values to "0" by default

From: John Brown <john.brown3@hp.com>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch changes Line In as Out Switch and Mic In as Out Switch to
enums for consistency, and causes all mic and line in ports to be probed
and controls to be added appropriately.
Signed-off-by: NNickolas Lloyd <ultrageek.lloyd@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Support 8 channel HDMI audio for MCP78/7A
Signed-off-by: NWei Ni <wni@nvidia.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ICH6_GCTL_RESET was wrongly set to another bit by the commit
b21fadb9.  This caused a problem when
the codec needs really a reset (e.g. recovering from the communication
error at probe).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The commit 86d190e7 reverted the bit
flip of LED GPIO for HP DX and DV4-1222nr.  Fixed now.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added some missing register bits definitions to reduce magic numbers.
Also renamed some to follow the names on the datasheet.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In the single_cmd mode, the hardware cannot store the multiple replies
like on RIRB, thus each verb has to sync and wait for the response no
matter whether the return value is needed or not.  Otherwise it may
result in a wrong return value from the previous verb.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

A docking mic control is shown by default. The Compaq Presario
CQ60 laptop has no docking connector, so designate it as a
CXT5051_HP model.
This makes the phantom mixer slider disappear.
Signed-off-by: NTony Vroon <tony@linx.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds a debug mode to make the codec communication
synchronous.  Define SND_HDA_SUPPORT_SYNC_WRITE in hda_codec.c,
and the call of snd_hda_codec_write*() will become synchronous,
i.e. wait for the reply from the codec at each time issuing a verb.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In the single_cmd mode, the current driver code doesn't do any update
for RIRB just for any safety reason.  But, actually the RIRB and
single_cmd mode don't conflict.  Unsolicited events can be delivered
even while using the single_cmd mode.

This patch allows the handling of unsolicited events with single_cmd
mode, just always checking RIRB independent from single_cmd flag.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

- Remove unneeded semicolons
- Introduce spec->gpio_led to specify the GPIO bit for LED control
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When a codec communication error occurs, the CORB/RIRB counters should
be reset first before re-issuing the verb.  Simply call azx_free_cmd_io()
and azx_init_cmd_io() to achieve that.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some Realtek codecs like ALC861 seem to support only VREF50 while the
current driver assumes it's only VREF80.  Check other VREF bits to set
the correct value.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The recent fix for the headphone volume control on IDT/STAC codecs
resulted in the removal of invalid "Side" volume eventually.  But,
if the front panel doesn't exist, this setup could be regarded as a
sort of regression, as reported in kernel bug #13250.

Now as a workaround, a new model 5stack-no-fp is added so that the user
without the front panel can choose this one explicitly.

Reference: bko#13250
	http://bugzilla.kernel.org/show_bug.cgi?id=13250Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ASUS W5Fm needs the fixed codec-slots to probe to override the BIOS
problem like W5F.
Tested-by: NAlp Kılıç <kilic.alp@gmail.com>
Signed-off-by: NOzan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fixes https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4121

Taken from https://bugzilla.redhat.com/show_bug.cgi?id=498060Signed-off-by: NAdam Williamson <awilliam@redhat.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The digital beep tone is calculated in two different ways depending
on the codec chip.  The standard one is using a divider, and another
one is a linear tone for IDT/STAC codecs.  Currently, only the
latter type is used for all codecs, which resulted in a wrong tone
pitch.

This patch adds the calculation of the standard HD-audio type.
Also clean-up the fields in hda_beep struct.

Reference: bko#13162
	http://bugzilla.kernel.org/show_bug.cgi?id=13162Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add proper prefix to each kernel message in hda_intel.c.
Also, avoid the unneeded prefix when CONFIG_SND_VERBOSE_PRINTK is used
together with snd_print*().

Reference: bko#13207
	http://bugzilla.kernel.org/show_bug.cgi?id=13207Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds support for MacBook 3,1 sound by adding a model new
"mb31" with the appropriate init verbs, mixers and channel modes to
the ALC883 configuration. patch_alc882() and patch_alc883() are
modified to handle the MacBook 3,1 sound-chip (Realtek ALC889A)
correctly.
Signed-off-by: NTorben Schulz <public@letorbi.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The PCI entries of Creative with HD-audio class can be the devices
with emu20k1/emu20k2 chips.  These are supported better by snd-ctxfi
driver.  With that driver, the device will mutate from HD-audio to
its native class.

This patch adds a simple ifdef to avoid the conflict of device probe
between snd-hda-intel and snd-ctxfi drivers.  1102:0009 seems still
OK to be added as it has no emu20kx chip, and is a pure HD-audio
device.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Show the actual chip name in 'unknown model..' info messages for
Realtek codecs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Split the name string in hda_codec struct to vendor_name and chip_name
strings to be stored directly from the preset name.
Since mostly only the chip name is referred in many patch_*.c, this
results in the reduction of many codes in the end.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds a mixer control for the STAC92XX boards to control the
DC bias of mic ports, allowing recording from both powered and
non-powered sources.  It replaces the "Mic Output Switch" with "Mic Jack
Mode" to switch between Mic, Line In, and Line Out.
Signed-off-by: NNickolas Lloyd <ultrageek.lloyd@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added the codec SSID for MacBook Pro 5,1 as compatible as MP51.
However, the headphone auto-muting function doesn't work.  So,
this is just a tentative solution.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The model=acer for ALC883/889 doesn't work well for the recent Acer
Aspire laptops.  Since model=auto works better nowadays, it's safer
to use the default fallback instead of the Acer specific one.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add specific configuration for Samsung NC10 mini notebook.  Internal
mic/speakers will be correctly muted when plugging in external ones.
Mixer controls are added for speakers, headphones and PC beep.
"Boost" is added for the microphones.
Signed-off-by: NChris Pockelé <chris.pockele.f1@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added the missing descriptions and the model names for Realtek codecs
to the documentation and the config table.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>