The 'wacom_wireless_work' function does not recalculate the tablet's
resolution, causing the value contained in the 'features' struct to
always be reported to userspace. This value is valid only for the pen
interface, meaning that the value will be incorrect for the touchpad (if
present). This in particular causes problems for libinput which relies
on the reported resolution being correct.

This patch adds the necessary calls to recalculate the resolution for
each interface. This requires a little bit of code shuffling since both
the 'wacom_set_default_phy' and 'wacom_calculate_res' are declared below
their new first point of use in 'wacom_wireless_work'.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

As an extension of aef3156d, there is no sense in repeatedly calling the
'wacom_set_report' and 'wacom_get_report' functions if they return an
error. Getting an error from them implies that the device is out to lunch:
either a hard error code was returned or repeated attempts at recovering
from a "soft" error all failed. In either case, doing even more retries is
not likely to resolve whatever is wrong.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The input_free_device() function tests whether its argument is NULL and
then returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NJiri Kosina <jkosina@suse.com>

We can't pass a NULL to input_unregister_device().

Fixes: 2a6cdbdd ('HID: wacom: Introduce new 'touch_input' device')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Instead of having a single 'input_dev' device that will take either pen
or touch data depending on the type of the device, create seperate devices
devices for each. By splitting things like this, we can support devices
(e.g. the I2C "AES" sensors in some newer tablet PCs) that send both pen
and touch reports from a single endpoint.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This splits the 'wacom_setup_pentouch_input_capabilites' function into
pieces dedicated to doing setup for just the pen interface and just
the touch interface. This makes it easier to focus on the relevant
piece when making changes.

This patch introduces no functional changes.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Historically, both the touch and pad tools would have shared the
'BTN_TOOL_FINGER' type. Any time you needed to distinguish the two, you
had to use some other bit of knowledge (e.g. that the pad was on the same
interface as the pen, and thus 'touch_max' would be zero).

To make these checks more readable, we introduce WACOM_DEVICETYPE_PAD.
Although we still have to rely on other bits of knowledge to set this
bit on the right interface (since it cannot be detected from the HID
descriptor), it can be done just once inside 'wacom_setup_device_quirks'.

This patch introduces no functional changes.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The USB devices that this driver has historically supported segregate the
pen and touch portions of the tablet. Oftentimes the segregation would be
done at the interface level, though on occasion (e.g. Cintiq 24HDT) the
tablet would combine two totally independent USB devices behind an internal
USB hub. Because pen and touch never shared the same interface, it made
sense for the 'device_type' to store a single value: "pen" or "touch".

Recently, however, some I2C devices have been created which combine the
two. A first step to accomodating this is to expand 'device_type' so that
it can represent two (or potentially more) types simultaneously. To do
this, we treat it as a bitfield and set/check individual bits rather
than using the '=' and '==' operators.

This should not result in any functional change since no supported devices
(that I'm aware of, at least) have HID descriptors that indicate both
pen and touch reports on a single interface.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

A little bit of cleanup work for 'wacom_update_name' to make it easier on
the eyes. Creates a temporary 'name' variable on which we'll perform our
edits. Once the name is in its final form, it will be copied (with
appropriate suffix) to 'wacom_wac->name' and 'wacom_wac->pad_name'.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Hardware may not respond to a request for the HID_DG_CONTACTMAX feature and
we should be tolerant of such a failure. This is especially true when using
hid-replay where the hardware doesn't exist, but also for devices attached
to a flaky bus. This patch increases the number of allowable retries to
match other calls to 'wacom_get_report' and also provides a fallback which
forces 'touch_max = 16' (enough for any Wacom device seen so far).
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Retrying on -EPIPE makes very little sense since this typically indicates
a problem that will not just disappear on its own. For instance, the USB
documentation states that it will be sent if the endpoint is stalled or
the device has disconnected. Instead, we should retry if -EAGAIN is
received since this indicates a temporary error condition such as a busy
bus.

In addition to adjusting the conditions we retry under, we also log an
error on failure so that we can be aware of what's going on.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The last patch was careful to maintain backwards-compatible behavior
by forcing device_type to BTN_TOOL_PEN (and printing a warning) if it
were still uninitialized after scanning the HID descriptor and applying
quirks. We should be more strict with HID_GENERIC devices, however,
since there is no a priori guarantee that it is a tablet or touchpad.
If the device_type is still uninitialized for a HID_GENERIC device then
we assume that it isn't something the driver can work with and so fail
the probe.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Currently, we assume a device_type of BTN_TOOL_PEN before scanning the
HID descriptor and then change the device_type if what we discover
proves that assumption wrong. This way of doing things makes it more
difficult to figure out if a device (particularly a HID_GENERIC device)
actually does tablet/touch input or is something completley different.

This patch leaves device_type at its initial value of 0 and then calls
'wacom_parse_hid' for every device (not just those that have touch).
As we map the usages, we can set the device_type as before. After we're
finished, we can then check if the value is still zero and do whatever
is most appropriate.

Detecting the pen can be a little tricky on most Wacom devices because
the descriptors describe opaque blobs. Fortunately, older Wacom tablets
have the HID_DG_DIGITIZER usage on the pen's application collection and
newer tablets seem to have a similar vendor-defined usage that we can
trigger on.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The naming logic currently assumes that all devices will be a pen, finger,
or pad. Though this has historically been the case, the new HID_GENERIC
catch-all may cause us to probe devices with Wacom's 056A VID which aren't
any of these types (e.g. the "Cintiq 24HDT Monitor Control"). This patch
updates the logic so that no suffix will be added to the device name if
the device type is unknown.
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

HID generic devices share the same default name, "Wacom HID". This
causes userland programs to show same device names for different
devices, which would confuse end users with same device names for
different devices too.

This patch uses name retrieved from HID descriptor, if a meaningful
name is reported. Otherwise, affix its product ID to "Wacom HID".

Names from descriptor may contain extra whitespaces. To comfort
readers' eyes, we removed those extra whitespaces too.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

That is where they belong...
Signed-off-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

It makes probe routine easy to follow.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The quirk was added for devices that support both pen and touch.  It decides if
a device supports multiple inputs by hardcoded feature type. However, for some
devices, we do not know if they support both before accessing their HID
descriptors.

This patch relies on dynamically assigned device_type to make the decision.
Also, we make it certain that wacom_wac->shared is always created. That is, the
driver will not be loaded if it fails to create wacom_wac->shared.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

If noone listens to the input device when a tool comes in proximity,
the tablet does not send the in-prox event when a client becomes available.
That means that no events will be sent until the tool is taken out of
proximity.

In this situation, ask for the report WACOM_REPORT_INTUOSREAD which will
read the corresponding feature and generate an in-prox event.
To make some generation of hardware working, we need to unset the
quirk NO_GET set by hid-core because the interfaces are seen as "boot
mouse".

We don't schedule this read in a worker while we are in an IO interrupt.
We know that usbhid will do it asynchronously. If this is triggered by
uhid, then this is obviously a client side bug :)
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Change the ownership of power_supply structure from each driver
implementing the class to the power supply core.

The patch changes power_supply_register() function thus all drivers
implementing power supply class are adjusted.

Each driver provides the implementation of power supply. However it
should not be the owner of power supply class instance because it is
exposed by core to other subsystems with power_supply_get_by_name().
These other subsystems have no knowledge when the driver will unregister
the power supply. This leads to several issues when driver is unbound -
mostly because user of power supply accesses freed memory.

Instead let the core own the instance of struct 'power_supply'.  Other
users of this power supply will still access valid memory because it
will be freed when device reference count reaches 0. Currently this
means "it will leak" but power_supply_put() call in next patches will
solve it.

This solves invalid memory references in following race condition
scenario:

Thread 1: charger manager
Thread 2: power supply driver, used by charger manager

THREAD 1 (charger manager)         THREAD 2 (power supply driver)
==========================         ==============================
psy = power_supply_get_by_name()
                                   Driver unbind, .remove
                                     power_supply_unregister()
                                     Device fully removed
psy->get_property()

The 'get_property' call is executed in invalid context because the driver was
unbound and struct 'power_supply' memory was freed.

This could be observed easily with charger manager driver (here compiled
with max17040 fuel gauge):

$ cat /sys/devices/virtual/power_supply/cm-battery/capacity &
$ echo "1-0036" > /sys/bus/i2c/drivers/max17040/unbind
[   55.725123] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[   55.732584] pgd = d98d4000
[   55.734060] [00000000] *pgd=5afa2831, *pte=00000000, *ppte=00000000
[   55.740318] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
[   55.746210] Modules linked in:
[   55.749259] CPU: 1 PID: 2936 Comm: cat Tainted: G        W       3.19.0-rc1-next-20141226-00048-gf79f475f3c44-dirty #1496
[   55.760190] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[   55.766270] task: d9b76f00 ti: daf54000 task.ti: daf54000
[   55.771647] PC is at 0x0
[   55.774182] LR is at charger_get_property+0x2f4/0x36c
[   55.779201] pc : [<00000000>]    lr : [<c034b0b4>]    psr: 60000013
[   55.779201] sp : daf55e90  ip : 00000003  fp : 00000000
[   55.790657] r10: 00000000  r9 : c06e2878  r8 : d9b26c68
[   55.795865] r7 : dad81610  r6 : daec7410  r5 : daf55ebc  r4 : 00000000
[   55.802367] r3 : 00000000  r2 : daf55ebc  r1 : 0000002a  r0 : d9b26c68
[   55.808879] Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
[   55.815994] Control: 10c5387d  Table: 598d406a  DAC: 00000015
[   55.821723] Process cat (pid: 2936, stack limit = 0xdaf54210)
[   55.827451] Stack: (0xdaf55e90 to 0xdaf56000)
[   55.831795] 5e80:                                     60000013 c01459c4 0000002a c06f8ef8
[   55.839956] 5ea0: db651000 c06f8ef8 daebac00 c04cb668 daebac08 c0346864 00000000 c01459c4
[   55.848115] 5ec0: d99eaa80 c06f8ef8 00000fff 00001000 db651000 c027f25c c027f240 d99eaa80
[   55.856274] 5ee0: d9a06c00 c0146218 daf55f18 00001000 d99eaa80 db4c18c0 00000001 00000001
[   55.864468] 5f00: daf55f80 c0144c78 c0144c54 c0107f90 00015000 d99eaab0 00000000 00000000
[   55.872603] 5f20: 000051c7 00000000 db4c18c0 c04a9370 00015000 00001000 daf55f80 00001000
[   55.880763] 5f40: daf54000 00015000 00000000 c00e53dc db4c18c0 c00e548c 0000000d 00008124
[   55.888937] 5f60: 00000001 00000000 00000000 db4c18c0 db4c18c0 00001000 00015000 c00e5550
[   55.897099] 5f80: 00000000 00000000 00001000 00001000 00015000 00000003 00000003 c000f364
[   55.905239] 5fa0: 00000000 c000f1a0 00001000 00015000 00000003 00015000 00001000 0001333c
[   55.913399] 5fc0: 00001000 00015000 00000003 00000003 00000002 00000000 00000000 00000000
[   55.921560] 5fe0: 7fffe000 be999850 0000a225 b6f3c19c 60000010 00000003 00000000 00000000
[   55.929744] [<c034b0b4>] (charger_get_property) from [<c0346864>] (power_supply_show_property+0x48/0x20c)
[   55.939286] [<c0346864>] (power_supply_show_property) from [<c027f25c>] (dev_attr_show+0x1c/0x48)
[   55.948130] [<c027f25c>] (dev_attr_show) from [<c0146218>] (sysfs_kf_seq_show+0x84/0x104)
[   55.956298] [<c0146218>] (sysfs_kf_seq_show) from [<c0144c78>] (kernfs_seq_show+0x24/0x28)
[   55.964536] [<c0144c78>] (kernfs_seq_show) from [<c0107f90>] (seq_read+0x1b0/0x484)
[   55.972172] [<c0107f90>] (seq_read) from [<c00e53dc>] (__vfs_read+0x18/0x4c)
[   55.979188] [<c00e53dc>] (__vfs_read) from [<c00e548c>] (vfs_read+0x7c/0x100)
[   55.986304] [<c00e548c>] (vfs_read) from [<c00e5550>] (SyS_read+0x40/0x8c)
[   55.993164] [<c00e5550>] (SyS_read) from [<c000f1a0>] (ret_fast_syscall+0x0/0x48)
[   56.000626] Code: bad PC value
[   56.011652] ---[ end trace 7b64343fbdae8ef1 ]---
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>

[for the nvec part]
Reviewed-by: NMarc Dietrich <marvin24@gmx.de>

[for compal-laptop.c]
Acked-by: NDarren Hart <dvhart@linux.intel.com>

[for the mfd part]
Acked-by: NLee Jones <lee.jones@linaro.org>

[for the hid part]
Acked-by: NJiri Kosina <jkosina@suse.cz>

[for the acpi part]
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Add new structure 'power_supply_config' for holding run-time
initialization data like of_node, supplies and private driver data.

The power_supply_register() function is changed so all power supply
drivers need updating.

When registering the power supply this new 'power_supply_config' should be
used instead of directly initializing 'struct power_supply'. This allows
changing the ownership of power_supply structure from driver to the
power supply core in next patches.

When a driver does not use of_node or supplies then it should use NULL
as config. If driver uses of_node or supplies then it should allocate
config on stack and initialize it with proper values.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: NPavel Machek <pavel@ucw.cz>

[for the nvec part]
Reviewed-by: NMarc Dietrich <marvin24@gmx.de>

[for drivers/platform/x86/compal-laptop.c]
Reviewed-by: NDarren Hart <dvhart@linux.intel.com>

[for drivers/hid/*]
Reviewed-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Declare the POWER_SUPPLY_PROP_PRESENT property to provide userspace
with a way to determine if the battery on a wireless tablet is plugged
in. Although current wireless tablets do not explicitly report this
information, it can be inferred from other state information. In
particular, a battery is assumed to be present if any of the following
are true: a non-zero battery level reported, the battery is reported as
charging, or the tablet is operating wirelessly.

Note: The last condition above may not strictly hold for the Graphire
Wireless (it charges from a DC barrel jack instead of a USB port), but I
do not know what is reported in the no-battery condition.
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The status packet for tablets which can use a wireless module contains a
bit that is set if the battery is charging. This bit will be 0 if either
a battery is not present or if the battery has reached full charge. Note
that the charging circuit may continue to charge the battery for a short
time after reaching "100%".
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Tablets like the Intuos, Intuos Pro, and Bamboo have a connector for an
optional wireless module that can be connected on the fly. The presence
(or absence) of this module is indicated in a status report recieved
from the tablet. This patch adds a workqueue function that will create
or destroy a power_supply object at runtime to match the current state
of the WACOM_QUIRK_BATTERY flag.
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The stylus of this device works just fine out of the box.
The touch is seen by default as a mouse with relative events and some
gestures.
The wireless and the wired version have slightly different firmwares, but
the debug mode 2 on the feature 2 is common to the 2 devices. In this mode,
all the reports are emitted through the debug interface (pen, raw touch
and mouse emulation), so we have to re-route manually the events.

We keep the Pen interface as a HID_GENERIC one because it works, and only
parse the raw touches while discarding the mouse emulation & gestures.

Switching the default in raw mode allows us to have a consistent user
experience accross all the multitouch touchpads (and enable the touch part
of the devices).

Note that the buttons of this devices are reported through the touch
interface. There is no 'Pad' interface. It seemed more natural to have
the BTN_LEFT and BTN_RIGHT reported with the touch because they are
placed under the touch interface and it looks like they belong to the
touch part.
Tested-by: NJosep Sanchez Ferreres <josep.sanchez.ferreres@est.fib.upc.edu>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The Bamboo PAD in debug mode needs to re-route events from the debug
interface to the Pen interface. This can be easily done with
hid_input_report(), but that means that we need to keep a reference to
the various hid_devices.

There should be only one touch and one pen interface per physical tablet,
so there is no need to keep a list of hid-devices, plain pointers are
sufficient.
Tested-by: NJosep Sanchez Ferreres <josep.sanchez.ferreres@est.fib.upc.edu>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

These devices have accelerometers. To report accelerometer coordinates, a new
property, INPUT_PROP_ACCELEROMETER, is added.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

We introduced nice macros in wacom_wac.c to check whether a field is
a pen or a touch one.

wacom_usage_mapping() still uses it's own tests, which are not in sync with
the wacom_wac tests (.application is not checked).

That means that some legitimate fields might be filtered out from the
usage mapping, and thus will not be used properly while receiving the
events.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

If a HID descriptor places HID_DG_CONTACTID before HID_DG_X and HID_DG_Y then
the ABS_X and ABS_Y will not be automatically initialized by the call to
input_mt_init_slots. To ensure that this is not a problem, we relocate that
call to occur after HID parsing has been completed and we've initalized all the
multitouch axes.
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Since the conversion from USB to HID (in v3.17), some people reported a
freeze on boot with the wacom driver. Hans managed to get a stacktrace:

[  240.272331] Call Trace:
[  240.272338]  [<ffffffff813de7b9>] ? usb_hcd_submit_urb+0xa9/0xb10
[  240.272347]  [<ffffffff81555579>] schedule+0x29/0x70
[  240.272355]  [<ffffffff815559e6>] schedule_preempt_disabled+0x16/0x20
[  240.272363]  [<ffffffff81557365>] __mutex_lock_slowpath+0xe5/0x230
[  240.272372]  [<ffffffff815574c7>] mutex_lock+0x17/0x30
[  240.272380]  [<ffffffffa063c1d2>] wacom_resume+0x22/0x50 [wacom]
[  240.272396]  [<ffffffffa01aea8a>] hid_resume_common+0xba/0x110 [usbhid]
[  240.272404]  [<ffffffff813e5890>] ? usb_runtime_suspend+0x80/0x80
[  240.272417]  [<ffffffffa01aeb1d>] hid_resume+0x3d/0x70 [usbhid]
[  240.272425]  [<ffffffff813e44a6>] usb_resume_interface.isra.6+0xb6/0x120
[  240.272432]  [<ffffffff813e4774>] usb_resume_both+0x74/0x140
[  240.272439]  [<ffffffff813e58aa>] usb_runtime_resume+0x1a/0x20
[  240.272446]  [<ffffffff813b1912>] __rpm_callback+0x32/0x70
[  240.272453]  [<ffffffff813b1976>] rpm_callback+0x26/0xa0
[  240.272460]  [<ffffffff813b2d71>] rpm_resume+0x4b1/0x690
[  240.272468]  [<ffffffff812ab992>] ? radix_tree_lookup_slot+0x22/0x50
[  240.272475]  [<ffffffff813b2c1a>] rpm_resume+0x35a/0x690
[  240.272482]  [<ffffffff8116e9c9>] ? zone_statistics+0x89/0xa0
[  240.272489]  [<ffffffff813b2f90>] __pm_runtime_resume+0x40/0x60
[  240.272497]  [<ffffffff813e4272>] usb_autopm_get_interface+0x22/0x60
[  240.272509]  [<ffffffffa01ae8d9>] usbhid_open+0x59/0xe0 [usbhid]
[  240.272517]  [<ffffffffa063ac85>] wacom_open+0x35/0x50 [wacom]
[  240.272525]  [<ffffffff813f37b9>] input_open_device+0x79/0xa0
[  240.272534]  [<ffffffffa048d1c1>] evdev_open+0x1b1/0x200 [evdev]
[  240.272543]  [<ffffffff811c899e>] chrdev_open+0xae/0x1f0
[  240.272549]  [<ffffffff811c88f0>] ? cdev_put+0x30/0x30
[  240.272556]  [<ffffffff811c17e2>] do_dentry_open+0x1d2/0x320
[  240.272562]  [<ffffffff811c1cd1>] finish_open+0x31/0x50
[  240.272571]  [<ffffffff811d2202>] do_last.isra.36+0x652/0xe50
[  240.272579]  [<ffffffff811d2ac7>] path_openat+0xc7/0x6f0
[  240.272586]  [<ffffffff811cf012>] ? final_putname+0x22/0x50
[  240.272594]  [<ffffffff811d42d2>] ? user_path_at_empty+0x72/0xd0
[  240.272602]  [<ffffffff811d43fd>] do_filp_open+0x4d/0xc0
[...]

So here, wacom_open is called, and then wacom_resume is called by the
PM system. However, wacom_open already took the lock when wacom_resume
tries to get it. Freeze.

A little bit of history shows that this already happened in the past
- commit f6cd3783 ("Input: wacom - fix runtime PM related deadlock"),
and the solution was to call first the PM function before taking the lock.

The lock was introduced in commit commit e7224094 ("Input: wacom -
implement suspend and autosuspend") when the autosuspend feature has
been added. Given that usbhid already takes care of this very same
locking between suspend/resume, I think we can simply kill the lock
in open/close.

The lock is now used also with LEDs, so we can not remove it completely.
Reported-by: NHans Spath <inbox-546@hans-spath.de>
Tested-by: NHans Spath <inbox-546@hans-spath.de>
CC: stable@vger.kernel.org # v3.17+
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

In several hid drivers it is necessary to calculate the length of an
hid_report. This patch exports the existing static function hid_report_len of
hid-core.c as an inline function in hid.h
Signed-off-by: NMathieu Magnaudet <mathieu.magnaudet@enac.fr>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

PAD can be on pen interface (Intuos Pro and Cintiq series) or touch
interface (Bamboo PT and Intuos PT series) or its own interface
(Bamboo pen-only and Intuos Pen M/S). We need to mark it independently.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Bamboo models do not support HID_DG_CONTACTMAX. Plus, Bamboo pen-only
has touch descriptor. This leads to some complications in the code.

This patch also fixes duplicated PAD interfeaces for Intuos Pen
models.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

ISDv4 and v5 are plain HID devices. We can directly implement a generic
HID parsing/handling and remove the need to manually add those PID in
the list of supported devices.

This patch implements the pen support only. The finger part will come in
a later patch.

To be properly notified of an .event() and a .report(), we need to force
hid-core to go through the HID parsing. By default, wacom.ko binds only
hidraw, so the hid parsing is not done by hid-core. When a true HID device
is there, we add the flag HID_CLAIMED_DRIVER to hid->claimed which will
force hid-core to parse the incoming reports.
(Note that this can be easily backported by directly setting the .claimed
flag to HID_CLAIMED_DRIVER even if hid-core does not support
HID_CONNECT_DRIVER)
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This allows to have the input devices ready in while parsing the reports
descriptor.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

If the input can be created earlier during probe, we can already populate
them while reading the report descriptor. This way, we can rely on the
hid subsystem directly for tablets which already provide a meaningful
report descriptor (like ISDv4-5).

This patch only splits the allocation and registration, but do not
change where we allocate the input. This will come in a later patch.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

When we have to deal with new elements in probe, having the exit labels
named sequencially is a pain to maintain. Put a meaningful name instead
so that we do not have to renumber them on inserts.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: NJason Gerecke <killertofu@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Some Wacom tablets (at least the ISDv4 found in the Lenovo X230) timeout
during probe while retrieving the input reports.
The only time this information is valuable is during the feature_mapping
stage, so we can ask for it there and discard the generic input reports
retrieval.

This gives a code path closer to the wacom.ko driver when it was in the
input subtree (not HID).

Cc: stable@vger.kernel.org # requires cherry-pick of c64d8834Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Currently, tablets connected to the WL receiver all share the same
VID/PID. There is no way for the user space to know which one is which
besides parsing the name. We can force the PID to be set to the
actual hardware. This way, the input device will have the correct PID
which can be match in libwacom.

With only this trick, the pad input does not inherit the ID_INPUT_TABLET
udev property from its parent. We can force udev to accept it by declaring
a BTN_STYLUS which is never used.

This way, tablets connected through WL can be used from the user point of
view in the same way they are used while connected through wire.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>