The Marvell Berlin boards have a group based pinmuxing mechanism. This
adds the core driver support. We actually do not need any information
about the pins here and only have the definition of the groups.

Let's take the example of the uart0 pinmuxing on the BG2Q. Balls BK4 and
BH6 are muxed to respectively UART0 RX and TX if the group GSM12 is set
to mode 0:

Group	Modes	Offset Base	Offset	LSB	Bit Width
GSM12	3	sm_base		0x40	0x10	0x2

Ball	Group	Mode 0		Mode 1		Mode 2
BK4	GSM12	UART0_RX	IrDA0_RX	GPIO9
BH6	GSM12	UART0_TX	IrDA0_TX	GPIO10

So in order to configure BK4 -> UART0_TX and BH6 -> UART0_RX, we need
to set (sm_base + 0x40 + 0x10) &= ff3fffff.

As pin control registers are part of either chip control or system
control registers, that deal with a bunch of other functions we rely
on a regmap instead of exclusively remapping any resources.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

In case of resolving power management or similar issues it might be useful
to have these properties included in the debugfs output.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

If chip->to_irq is NULL ACPI GPIO helpers don't register GPIO event
handlers thus preventing any ACPI GPIO triggered events. Solve this by
calling gpiochip_add() after we have set up drivers chip->to_irq hook.
Signed-off-by: NJin Yao <yao.jin@intel.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Now that the x86 dynamic IRQ allocation problem has been resolved with
commmit 62a08ae2 (genirq: x86: Ensure that dynamic irq allocation does
not conflict), we can add back Baytrail-T ACPI ID to the pinctrl driver.

This makes the driver to work on Asus T100 where it is needed for several
things like ACPI GPIO events and SD card detection.

References: https://bugzilla.kernel.org/show_bug.cgi?id=68291Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NJin Yao <yao.jin@intel.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add #ifdefs to allow r8a73a4 Multiplatform build. Needed
to enable r8a73a4 Multiplatform support.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add #ifdefs to allow sh73a0 Multiplatform build. Needed
to enable sh73a0 Multiplatform support.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add #ifdefs to allow r8a7740 Multiplatform build. Needed
to enable r8a7740 Multiplatform support.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

In the multiplatform kernel case the IRQs associated with the PFC GPIOs
are specified through DT. The pinmux_irq irq field is thus ignored by
the code, and doesn't need to be set.

This will allow removing the mach/irq.h include from pfc-*.c files that
was required for the irq_pin() macro used to initialize the irq field.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Enable the freshly introduced Kconfig options whenever their matching
architecture is enabled.

Since the Kconfig symbols for these machines are going through a different
tree, keep PINCTRL_SUNXI around for the moment to avoid breaking the defconfig.
It should be removed eventually.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Introduce the syscons for grf and pmu and deprecate the previous register
areas.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This allows the basic registers of the general register files to be supplied
by a syscon instead of being mapped locally.

The GRF registers contain a lot more than pinctrl functions like dma, usb-phy
and general soc control and status registers, intermixed with the iomux, pull
and drive-strength registers.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When the pmu registers are supplied through a syscon regmap we do not need
to map the registers ourself.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Currently the pmu registers containing pin pull settings on the rk3188 are mapped
locally when bank0 is instantiated. Add an alternative that can resolve the pmu
from a syscon phandle.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Convert rockchip_get_bank_data to use the struct rockchip_pinctrl because
later on we need to check a value from it when registering the gpio banks.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This allows us to use syscons in the future.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Deprecate secondary register area for rk3188 pulls. Instead use big enough
initial mapping of grf registers to catch all.

The now deprecated register is still supported though.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Pinctrl cleanup and reworks for 3.16

This serie of patch:
  - Moves the Allwinner pinctrl driver to a folder of its own
  - removes the sunxi-pinctrl-pins header, and split the driver into a core
    one, with all the logic, and smaller drivers, one for each SoC, that
    declare the pins, and will provide to the core the set of pins.
  - And does a few cleanups here and there.

The way that reset is handled right now is that it is made optional for every
pinctrl driver, while actually, it isn't used at all for the main pin
controllers so far, and while it's mandatory for the A31's secondary pin
controller.

Move the reset functions out of the core and in the driver, where they can be
made mandatory.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add one Kconfig option for each driver. This will allow to better control which
driver is enabled, instead of having either all or nothing.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Move the pin description to a driver specific to be.

This is the final step toward retiring pinctrl-sunxi-pins.h that used to define
all the pins for all the Allwinner SoCs in a single header, that would have in
turn result in having these structures in the final binary as many times as the
header was included.

We can finally remove that header, and remove all the driver part of the
pinctrl-sunxi core.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This will allow to have multiple drivers using the same core code, and
eventually, retire pinctrl-sunxi-pins.h
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The previous code was calling of_iomap, which doesn't do any resource
management, and doesn't call request_mem_region either. Use
devm_ioremap_resource that do both.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

We previously had an evergrowing (and exhaustive) list of the pins that could
be used on any Allwinner SoCs. These defines were then used by each pinctrl
driver to declare the list of functions for this pin. Since it's pretty much
all boilerplate, we can remove it just by a single macro.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This will allow to create numerous files without crippling the main pinctrl
directory.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The ranges and nranges were never used. Remove them.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The pins description structure were declared as const, but the of_device_id
data magic was losing it silently.

Make sure we have it on both sides.

And now that we're using const, we can also remove the useless cast in probe.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Fix copy/paste error in pinctrl_pin_desc for pin 0.
Signed-off-by: NAndy Gross <agross@codeaurora.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This commit extends the pinctrl mvebu logic with a new driver to cover
Orion5x SoC. It supports the definitions for the 5181l, 5182 and 5281
variants of Orion5x, which are the three ones supported by the old
style MPP code in arch/arm/mach-orion5x/.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

In some cases it is nice to be able to simply control a gpio output
via the PIN_CONFIG_OUTPUT option without having a driver control it.
Thus add support for it to the rockchip pinctrl driver.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Till now pinconf_get only set the argument value into the config parameter
effectively removing the actual config param value. As other pinctrl drivers
do, it might be nicer to keep the config param intact.
Therefore construct a real pinconfig value from param and arg in pinconf_get
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This switches the SiRF pinctrl driver over to using the gpiolib
irqchip helpers simplifying some of the code.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

all gpio banks are in one chip, that makes software clean in mapping
irq and gpio.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The sirfsoc_irqchip_to_bank() is obviously misnamed, as it is
not converting an irqchip to a bank but converts a gpiochip
to a bank so rename it sirfsoc_gpiochip_to_bank().
Acked-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Define a new binding for the Qualcomm TLMMv2 based pin controller inside the
IPQ8064.
Signed-off-by: NAndy Gross <agross@codeaurora.org>
Reviewed-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds pinctrl definitions for the GPIO pins of the TLMM v2 block in the
Qualcomm IPQ8064 platform.
Signed-off-by: NAndy Gross <agross@codeaurora.org>
Reviewed-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>