- 08 12月, 2009 15 次提交
-
-
由 Lennert Buytenhek 提交于
Don't forget to call pci_disable_device() if pci_request_regions() fails during probe. Signed-off-by: NLennert Buytenhek <buytenh@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Lennert Buytenhek 提交于
The time between loading the helper image and starting to upload the main firmware image should be at least 5 ms or so. We were doing an msleep(1) before, and 1 ms appears to not be enough in almost all cases, but building with HZ=100 has always masked this so far. Bumping the msleep argument to 5 fixes firmware loading e.g. when HZ=1000. Some firmware images need more than 200ms to initialize. Bump the ready code timeout to 500ms to accommodate for this. Signed-off-by: NLennert Buytenhek <buytenh@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Lennert Buytenhek 提交于
Before issuing any firmware commands, we wait for the transmit rings to drain, to prevent control versus data path synchronization issues. In some cases, this can end up taking longer than the current hardcoded limit of 5 seconds, for example if the transmit rings are filled with packets for a host that has dropped off the air and we end up retransmitting every pending packet at the lowest rate a couple of times. This patch changes mwl8k_tx_wait_empty() to only bail out on timeout expiry if there was no change in the number of packets pending in the transmit rings during the waiting period. If at least one transmit ring entry was reclaimed while we were waiting, we are apparently still making progress, and we'll allow waiting for another timeout period. Signed-off-by: NLennert Buytenhek <buytenh@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Lennert Buytenhek 提交于
Some firmware commands can under some circumstances take more than 2 seconds to complete. This patch bumps the timeout up to 10 seconds, and prints a message whenever a command takes more than 2 seconds. Signed-off-by: NLennert Buytenhek <buytenh@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Lennert Buytenhek 提交于
On 8366, bit 6 in the rx descriptor rate field indicates whether the packet was received on a 20MHz or 40MHz channel, and is not part of the MCS index. Handle this properly, which then prevents hitting the WARN_ON and being dropped in ieee80211_rx(). Signed-off-by: NLennert Buytenhek <buytenh@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Lennert Buytenhek 提交于
When inserting a DMA header into a packet for transmission, mwl8k_add_dma_header() would blindly zero the addr4 field, which is not a good idea if the packet being transmitted is actually a 4-address packet. Also, if the transmitted packet was a 4-address with QoS packet, the memmove() to do the needed header reshuffling would inadvertently overwrite the first two bytes of the packet payload with the QoS field. This fixes both of these issues. Signed-off-by: NLennert Buytenhek <buytenh@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Lennert Buytenhek 提交于
Packets exchanged between the mwl8k driver and the firmware always have a 4-address header without QoS field. For QoS packets, the QoS field is passed to/from the firmware via the tx/rx descriptors. We were handling this correctly on transmit, but not on receive -- if a QoS packet was received, we would leave garbage in the QoS field in the packet passed up to the stack, which is Bad(tm). Also, if the packet received on the air was a 4-address without QoS packet, we would forget to skb_pull the 2-byte DMA length prefix off. This patch adds an argument to the ->rxd_process() receive descriptor operation to retrieve the QoS field from the receive descriptor, and extends mwl8k_remove_dma_header() to insert this field back into the packet if the packet received is a QoS packet. It also fixes mwl8k_remove_dma_header() to strip off the length prefix in all cases. Signed-off-by: NLennert Buytenhek <buytenh@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Lennert Buytenhek 提交于
There exist 12 802.11b/g rates, but mwl8k supports two additional (non-standard) rates, and includes those rates in rate bitmasks and in its internal rate table that hardware rate indices index. Commit "mwl8k: report rate and other information for received frames" added one of the nonstandard rates to the mwl8k_rates table to make the OFDM rates in the table line up with the rate indices that are reported in the receive descriptor (so that we can just simply copy the receive descriptor rate index into ieee80211_rx_status::rate_idx) and bumped MWL8K_IEEE_LEGACY_DATA_RATES from 12 to 13, but this screwed up the UPDATE_STADB command struct layout, as it also uses that define, for its legacy_rates array. To avoid having to convert rate indices and legacy rate bitmaps (e.g. ieee80211_bss_conf::basic_rates) between the 12-rate mac80211 format and the 14-rate mwl8k format, we'll report all 14 rates in our wiphy's band, but filter out the nonstandard ones e.g. in the case of the UPDATE_STADB command which only accepts 12 rates. In the commands that accept 14 rates (SET_AID, SET_RATE), replace the use of the MWL8K_RATE_INDEX_MAX_ARRAY define in the command struct by the constant 14, to make it clearer that these commands accept 14 rates. Signed-off-by: NLennert Buytenhek <buytenh@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Lennert Buytenhek 提交于
The MCS bitmaps in the SET_RATE command structure were of the wrong size, due to use of the wrong define for the array length. Just hardcode the lengths as 16, and do the same for the MCS bitmaps in other command structures. Signed-off-by: NLennert Buytenhek <buytenh@marvell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vivek Natarajan 提交于
Not only ps_sdata but also IEEE80211_CONF_PS is to be considered before restoring PS in scan_ps_disable(). For instance, when ps_sdata is set but CONF_PS is not set just because the dynamic timer is still running, a sw scan leads to setting of CONF_PS in scan_ps_disable instead of restarting the dynamic PS timer. Also for the above case, a null data frame is to be sent after returning to operating channel which was not happening with the current implementation. This patch fixes this too. Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com> Reviewed-by: NKalle Valo <kalle.valo@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
hwsim testing has revealed that when the MLME recalculates the idle state of the device, it sometimes does so before sending the final deauthentication or disassociation frame. This patch changes the place where the idle state is recalculated, but of course driver transmit is typically asynchronous while configuration is expected to be synchronous, so it doesn't fix all possible cases yet. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Kalle Valo 提交于
The bssid can be zero when null data template is set in wl1251_op_config(). It's enough, and especially safe, to set it once after association. Signed-off-by: NKalle Valo <kalle.valo@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Kalle Valo 提交于
bssid needs to be copied first in wl1251_op_bss_info_changed(), otherwise templates will have incorrect bssid and power save will not work correctly. Signed-off-by: NKalle Valo <kalle.valo@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Kalle Valo 提交于
There was a warning from wl1251_op_bss_info_changed(): wl1251: WARNING Set ctsprotect failed 0 It was printed always, it's completely false and can be removed. Signed-off-by: NKalle Valo <kalle.valo@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
CC [M] drivers/net/wireless/iwlwifi/iwl-tx.o drivers/net/wireless/iwlwifi/iwl-tx.c: In function ‘iwl_tx_agg_stop’: drivers/net/wireless/iwlwifi/iwl-tx.c:1356: warning: passing argument 1 of ‘ieee80211_stop_tx_ba_cb_irqsafe’ from incompatible pointer type include/net/mac80211.h:2128: note: expected ‘struct ieee80211_vif *’ but argument is of type ‘struct ieee80211_hw *’ Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 06 12月, 2009 19 次提交
-
-
由 David S. Miller 提交于
Conflicts: drivers/net/pcmcia/fmvj18x_cs.c drivers/net/pcmcia/nmclan_cs.c drivers/net/pcmcia/xirc2ps_cs.c drivers/net/wireless/ray_cs.c
-
由 Linus Torvalds 提交于
Merge branch 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (40 commits) tracing: Separate raw syscall from syscall tracer ring-buffer-benchmark: Add parameters to set produce/consumer priorities tracing, function tracer: Clean up strstrip() usage ring-buffer benchmark: Run producer/consumer threads at nice +19 tracing: Remove the stale include/trace/power.h tracing: Only print objcopy version warning once from recordmcount tracing: Prevent build warning: 'ftrace_graph_buf' defined but not used ring-buffer: Move access to commit_page up into function used tracing: do not disable interrupts for trace_clock_local ring-buffer: Add multiple iterations between benchmark timestamps kprobes: Sanitize struct kretprobe_instance allocations tracing: Fix to use __always_unused attribute compiler: Introduce __always_unused tracing: Exit with error if a weak function is used in recordmcount.pl tracing: Move conditional into update_funcs() in recordmcount.pl tracing: Add regex for weak functions in recordmcount.pl tracing: Move mcount section search to front of loop in recordmcount.pl tracing: Fix objcopy revision check in recordmcount.pl tracing: Check absolute path of input file in recordmcount.pl tracing: Correct the check for number of arguments in recordmcount.pl ...
-
由 Linus Torvalds 提交于
Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: tracing: Fix trace_marker output tracing: Fix event format export tracing: Fix return value of tracing_stats_read()
-
由 Linus Torvalds 提交于
Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: genirq: Fix spurious irq seqfile conversion genirq: switch /proc/irq/*/spurious to seq_file irq: Do not attempt to create subdirectories if /proc/irq/<irq> failed irq: Remove unused debug_poll_all_shared_irqs() irq: Fix docbook comments irq: trivial: Fix typo in comment for #endif
-
由 Linus Torvalds 提交于
Merge branch 'core-softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'core-softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: softlockup: Fix hung_task_check_count sysctl
-
由 Linus Torvalds 提交于
Merge branch 'core-signal-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'core-signal-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: signal: Print warning message when dropping signals signal: Fix alternate signal stack check
-
由 Linus Torvalds 提交于
Merge branch 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits) rcu: Make RCU's CPU-stall detector be default rcu: Add expedited grace-period support for preemptible RCU rcu: Enable fourth level of TREE_RCU hierarchy rcu: Rename "quiet" functions rcu: Re-arrange code to reduce #ifdef pain rcu: Eliminate unneeded function wrapping rcu: Fix grace-period-stall bug on large systems with CPU hotplug rcu: Eliminate __rcu_pending() false positives rcu: Further cleanups of use of lastcomp rcu: Simplify association of forced quiescent states with grace periods rcu: Accelerate callback processing on CPUs not detecting GP end rcu: Mark init-time-only rcu_bootup_announce() as __init rcu: Simplify association of quiescent states with grace periods rcu: Rename dynticks_completed to completed_fqs rcu: Enable synchronize_sched_expedited() fastpath rcu: Remove inline from forward-referenced functions rcu: Fix note_new_gpnum() uses of ->gpnum rcu: Fix synchronization for rcu_process_gp_end() uses of ->completed counter rcu: Prepare for synchronization fixes: clean up for non-NO_HZ handling of ->completed counter rcu: Cleanup: balance rcu_irq_enter()/rcu_irq_exit() calls ...
-
由 Linus Torvalds 提交于
Merge branch 'core-printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'core-printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: ratelimit: Make suppressed output messages more useful printk: Remove ratelimit.h from kernel.h ratelimit: Fix/allow use in atomic contexts ratelimit: Use per ratelimit context locking
-
由 Linus Torvalds 提交于
Merge branch 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: mutex: Fix missing conditions to build mutex_spin_on_owner() mutex: Better control mutex adaptive spinning config locking, task_struct: Reduce size on TRACE_IRQFLAGS and 64bit locking: Use __[SPIN|RW]_LOCK_UNLOCKED in [spin|rw]_lock_init() locking: Remove unused prototype locking: Reduce ifdefs in kernel/spinlock.c locking: Make inlining decision Kconfig based
-
由 Linus Torvalds 提交于
Merge branch 'core-ipi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'core-ipi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: generic-ipi: Add smp_call_function_any() generic-ipi: Fix misleading smp_call_function*() description
-
由 Linus Torvalds 提交于
Merge branch 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits) x86, Calgary IOMMU quirk: Find nearest matching Calgary while walking up the PCI tree x86/amd-iommu: Remove amd_iommu_pd_table x86/amd-iommu: Move reset_iommu_command_buffer out of locked code x86/amd-iommu: Cleanup DTE flushing code x86/amd-iommu: Introduce iommu_flush_device() function x86/amd-iommu: Cleanup attach/detach_device code x86/amd-iommu: Keep devices per domain in a list x86/amd-iommu: Add device bind reference counting x86/amd-iommu: Use dev->arch->iommu to store iommu related information x86/amd-iommu: Remove support for domain sharing x86/amd-iommu: Rearrange dma_ops related functions x86/amd-iommu: Move some pte allocation functions in the right section x86/amd-iommu: Remove iommu parameter from dma_ops_domain_alloc x86/amd-iommu: Use get_device_id and check_device where appropriate x86/amd-iommu: Move find_protection_domain to helper functions x86/amd-iommu: Simplify get_device_resources() x86/amd-iommu: Let domain_for_device handle aliases x86/amd-iommu: Remove iommu specific handling from dma_ops path x86/amd-iommu: Remove iommu parameter from __(un)map_single x86/amd-iommu: Make alloc_new_range aware of multiple IOMMUs ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw: (31 commits) GFS2: Fix glock refcount issues writeback: remove unused nonblocking and congestion checks (gfs2) GFS2: drop rindex glock to refresh rindex list GFS2: Tag all metadata with jid GFS2: Locking order fix in gfs2_check_blk_state GFS2: Remove dirent_first() function GFS2: Display nobarrier option in /proc/mounts GFS2: add barrier/nobarrier mount options GFS2: remove division from new statfs code GFS2: Improve statfs and quota usability GFS2: Use dquot_send_warning() VFS: Export dquot_send_warning GFS2: Add set_xquota support GFS2: Add get_xquota support GFS2: Clean up gfs2_adjust_quota() and do_glock() GFS2: Remove constant argument from qd_get() GFS2: Remove constant argument from qdsb_get() GFS2: Add proper error reporting to quota sync via sysfs GFS2: Add get_xstate quota function GFS2: Remove obsolete code in quota.c ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6由 Linus Torvalds 提交于
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (30 commits) TOMOYO: Add recursive directory matching operator support. remove CONFIG_SECURITY_FILE_CAPABILITIES compile option SELinux: print denials for buggy kernel with unknown perms Silence the existing API for capability version compatibility check. LSM: Move security_path_chmod()/security_path_chown() to after mutex_lock(). SELinux: header generation may hit infinite loop selinux: Fix warnings security: report the module name to security_module_request Config option to set a default LSM sysctl: require CAP_SYS_RAWIO to set mmap_min_addr tpm: autoload tpm_tis based on system PnP IDs tpm_tis: TPM_STS_DATA_EXPECT workaround define convenient securebits masks for prctl users (v2) tpm: fix header for modular build tomoyo: improve hash bucket dispersion tpm add default function definitions LSM: imbed ima calls in the security hooks SELinux: add .gitignore files for dynamic classes security: remove root_plug SELinux: fix locking issue introduced with c6d3aaa4 ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (50 commits) pcmcia: rework the irq_req_t typedef pcmcia: remove deprecated handle_to_dev() macro pcmcia: pcmcia_request_window() doesn't need a pointer to a pointer pcmcia: remove unused "window_t" typedef pcmcia: move some window-related code to pcmcia_ioctl.c pcmcia: Change window_handle_t logic to unsigned long pcmcia: Pass struct pcmcia_socket to pcmcia_get_mem_page() pcmcia: Pass struct pcmcia_device to pcmcia_map_mem_page() pcmcia: Pass struct pcmcia_device to pcmcia_release_window() drivers/pcmcia: remove unnecessary kzalloc pcmcia: correct handling for Zoomed Video registers in topic.h pcmcia: fix printk formats pcmcia: autoload module pcmcia pcmcia/staging: update comedi drivers PCMCIA: stop duplicating pci_irq in soc_pcmcia_socket PCMCIA: ss: allow PCI IRQs > 255 PCMCIA: soc_common: remove 'dev' member from soc_pcmcia_socket PCMCIA: soc_common: constify soc_pcmcia_socket ops member PCMCIA: sa1111: remove duplicated initializers PCMCIA: sa1111: wrap soc_pcmcia_socket to contain sa1111 specific data ...
-
由 David Daney 提交于
Use the new unreachable() macro instead of for(;;); Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 David Daney 提交于
Use the new unreachable() macro instead of for(;;); Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com> CC: Heiko Carstens <heiko.carstens@de.ibm.com> CC: linux390@de.ibm.com CC: linux-s390@vger.kernel.org Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 David Daney 提交于
Use the new unreachable() macro instead of while(1); Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Acked-by: NRalf Baechle <ralf@linux-mips.org> CC: linux-mips@linux-mips.org Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 David Daney 提交于
Use the new unreachable() macro instead of for(;;);. When allyesconfig is built with a GCC-4.5 snapshot on i686 the size of the text segment is reduced by 3987 bytes (from 6827019 to 6823032). Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Acked-by: N"H. Peter Anvin" <hpa@zytor.com> CC: Thomas Gleixner <tglx@linutronix.de> CC: Ingo Molnar <mingo@redhat.com> CC: x86@kernel.org Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 David Daney 提交于
Starting with version 4.5, GCC has a new built-in function __builtin_unreachable() that can be used in places like the kernel's BUG() where inline assembly is used to transfer control flow. This eliminated the need for an endless loop in these places. The patch adds a new macro 'unreachable()' that will expand to either __builtin_unreachable() or an endless loop depending on the compiler version. Change from v1: Simplify unreachable() for non-GCC 4.5 case. Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Acked-by: NRalf Baechle <ralf@linux-mips.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 05 12月, 2009 6 次提交
-
-
由 Johannes Berg 提交于
My patch "mac80211: correctly place aMPDU RX reorder code" uses an skb queue for MPDUs that were released from the buffer. I intentially didn't initialise and use the skb queue's spinlock, but in this place forgot that the code variant that doesn't touch the spinlock is needed. Thanks to Christian Lamparter for quickly spotting the bug in the backtrace Reinette reported. Reported-by: NReinette Chatre <reinette.chatre@intel.com> Bug-identified-by: NChristian Lamparter <chunkeey@googlemail.com> Tested-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Samuel Ortiz 提交于
When debugging the wifi firmware, we need to disable the wimax core to gain some memory space. The default value will keep the wimax core enabled. Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Samuel Ortiz 提交于
Wifi and wimax coexistence mode is set by wifi at boot time. There can be several modes, defined by priority tables. User space components can decide which one to select by writing to /sys/module/iwmc3200wifi/parameters/wiwi with this patch, before bringing the interface up. Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Samuel Ortiz 提交于
When sending the wiwi coexistence priority table, we should not tell the LMAC that we want a response. Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Samuel Ortiz 提交于
This update follows the firmware engineers recommendations. Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-