This allows for upper levels in the driver, e.g the TC offload code to add
e-switch offloaded steering rules. The caller provides the rule spec for
matching, action, source and destination vports.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the offloads mode, some slow path rules are added by the driver (e.g
send-to-vport), while offloaded rules are to be added from upper layers.

The slow path rules have lower priority and we don't want matching on
offloaded rules to suffer from extra steering hops related to the slow
path rules.

We use two priorities, one for offloaded rules (fast path), and one for
the control rules (slow path). To allow for that, we enable two priorities
for the FDB namespace in the FS core code.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currenly, the code that programs the flow actions into the firmware
doesn't check if was actually asked to offload the statistics, fix that.

Fixes: aad7e08d ('net/mlx5e: Hardware offloaded flower filter statistics support')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit utilize the ability of ConnectX-4 to bulk read flow counters.
Few bulk counter queries could be done instead of issuing thousands of
firmware commands per second to get statistics of all flows set to HW,
such as those programmed when we offload tc filters.

Counters are stored sorted by hardware id, and queried in blocks (id +
number of counters).

Due to hardware requirement, start of block and number of counters in a
block must be four aligned.
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NAmir Vadai <amir@vadai.me>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to use bulk counters, we need to have counters sorted by id.
Signed-off-by: NAmir Vadai <amir@vadai.me>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Elad Kanfi says:

====================
Code style fixes

Fix all checkpatch warnings and errors, and reuse code
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add inline function that checks if there is a pending tx packet.
Signed-off-by: NElad Kanfi <eladkan@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix following coding style problems :

ERROR: else should follow close brace '}'
+	}
+	else { /* !dst_is_aligned */

WARNING: Missing a blank line after declarations
+			u32 buf = nps_enet_reg_get(priv, NPS_ENET_REG_RX_BUF);
+			put_unaligned_be32(buf, reg);

WARNING: Missing a blank line after declarations
+		u32 buf;
+		ioread32_rep(priv->regs_base + NPS_ENET_REG_RX_BUF, &buf, 1);

CHECK: Blank lines aren't necessary before a close brace '}'
+
+	}

total: 1 errors, 2 warnings, 1 checks, 683 lines checked
Signed-off-by: NElad Kanfi <eladkan@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marcelo Ricardo Leitner says:

====================
sctp: allow GSO frags to access the chunk too

Patchset is named after the most important fix in it. First two patches
are preparing the grounds for the 3rd patch.

After the 3rd, they are not strictly logically related to the patchset,
but I kept them together as they depend on each other.

More details on patch changelogs.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently only read-only checks are performed up to the point on where
we check if peer is ECN capable, checks which we can avoid otherwise.
The flag ecn_ce_done is only used to perform this check once per
incoming packet, and nothing more.

Thus this patch moves the peer check up.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should not clear that flag when switching to a new skb from a GSO skb
because it would cause ECN processing to happen multiple times per GSO
skb, which is not wanted. Instead, let it be processed once per chunk.
That is, in other words, once per IP header available.

Fixes: 90017acc ("sctp: Add GSO support")
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Identifying address family operations during rx path is not something
expensive but it's ugly to the eye to have it done multiple times,
specially when we already validated it during initial rx processing.

This patch takes advantage of the now shared sctp_input_cb and make the
pointer to the operations readily available.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SCTP will try to access original IP headers on sctp_recvmsg in order to
copy the addresses used. There are also other places that do similar access
to IP or even SCTP headers. But after 90017acc ("sctp: Add GSO
support") they aren't always there because they are only present in the
header skb.

SCTP handles the queueing of incoming data by cloning the incoming skb
and limiting to only the relevant payload. This clone has its cb updated
to something different and it's then queued on socket rx queue. Thus we
need to fix this in two moments.

For rx path, not related to socket queue yet, this patch uses a
partially copied sctp_input_cb to such GSO frags. This restores the
ability to access the headers for this part of the code.

Regarding the socket rx queue, it removes iif member from sctp_event and
also add a chunk pointer on it.

With these changes we're always able to reach the headers again.

The biggest change here is that now the sctp_chunk struct and the
original skb are only freed after the application consumed the buffer.
Note however that the original payload was already like this due to the
skb cloning.

For iif, SCTP's IPv4 code doesn't use it, so no change is necessary.
IPv6 now can fetch it directly from original's IPv6 CB as the original
skb is still accessible.

In the future we probably can simplify sctp_v*_skb_iif() stuff, as
sctp_v4_skb_iif() was called but it's return value not used, and now
it's not even called, but such cleanup is out of scope for this change.

Fixes: 90017acc ("sctp: Add GSO support")
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The next patch needs 8 bytes in there. sctp_ulpevent has a hole due to
bad alignment; msg_flags is using 4 bytes while it actually uses only 2, so
we shrink it, and iif member (4 bytes) which can be easily fetched from
another place once the next patch is there, so we remove it and thus
creating space for 8 bytes.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We process input path in other files too and having access to it is
nice, so move it to a header where it's shared.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Comments from Frank Kellerman on last doc update:
- extra whitespace in front of a neigh show command
- convert the brief link example to 'vrf red'
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2016-07-13

Here's our main bluetooth-next pull request for the 4.8 kernel:

 - Fixes and cleanups in 802.15.4 and 6LoWPAN code
 - Fix out of bounds issue in btmrvl driver
 - Fixes to Bluetooth socket recvmsg return values
 - Use crypto_cipher_encrypt_one() instead of crypto_skcipher
 - Cleanup of Bluetooth connection sysfs interface
 - New Authentication failure reson code for Disconnected mgmt event
 - New USB IDs for Atheros, Qualcomm and Intel Bluetooth controllers

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update vrf documentation for changes made to 4.4 - 4.8 kernels
and iproute2 support for vrf keyword.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Increment the mgmt revision due to the recently added new
reason code for the Disconnected event.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If link is disconnected due to Authentication Failure (PIN or Key
Missing status) userspace will be notified about this with proper error
code. Many LE profiles define "PIN or Key Missing" status as indication
of remote lost bond so this allows userspace to take action on this.

@ Device Connected: 88:63:DF:88:0E:83 (1) flags 0x0000
        02 01 1a 05 03 0a 18 0d 18 0b 09 48 65 61 72 74  ...........Heart
        20 52 61 74 65                                    Rate
> HCI Event: Command Status (0x0f) plen 4
      LE Read Remote Used Features (0x08|0x0016) ncmd 1
        Status: Success (0x00)
> ACL Data RX: Handle 3585 flags 0x02 dlen 11
      ATT: Read By Group Type Request (0x10) len 6
        Handle range: 0x0001-0xffff
        Attribute group type: Primary Service (0x2800)
> HCI Event: LE Meta Event (0x3e) plen 12
      LE Read Remote Used Features (0x04)
        Status: Success (0x00)
        Handle: 3585
        Features: 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00
          LE Encryption
< HCI Command: LE Start Encryption (0x08|0x0019) plen 28
        Handle: 3585
        Random number: 0x0000000000000000
        Encrypted diversifier: 0x0000
        Long term key: 26201cd479a0921b6f949f0b1fa8dc82
> HCI Event: Command Status (0x0f) plen 4
      LE Start Encryption (0x08|0x0019) ncmd 1
        Status: Success (0x00)
> HCI Event: Encryption Change (0x08) plen 4
        Status: PIN or Key Missing (0x06)
        Handle: 3585
        Encryption: Disabled (0x00)
< HCI Command: Disconnect (0x01|0x0006) plen 3
        Handle: 3585
        Reason: Authentication Failure (0x05)
> HCI Event: Command Status (0x0f) plen 4
      Disconnect (0x01|0x0006) ncmd 1
        Status: Success (0x00)
> HCI Event: Disconnect Complete (0x05) plen 4
        Status: Success (0x00)
        Handle: 3585
        Reason: Connection Terminated By Local Host (0x16)
@ Device Disconnected: 88:63:DF:88:0E:83 (1) reason 4

@ Device Connected: C4:43:8F:A3:4D:83 (0) flags 0x0000
        08 09 4e 65 78 75 73 20 35                       ..Nexus 5
> HCI Event: Command Status (0x0f) plen 4
      Authentication Requested (0x01|0x0011) ncmd 1
        Status: Success (0x00)
> HCI Event: Link Key Request (0x17) plen 6
        Address: C4:43:8F:A3:4D:83 (LG Electronics)
< HCI Command: Link Key Request Reply (0x01|0x000b) plen 22
        Address: C4:43:8F:A3:4D:83 (LG Electronics)
        Link key: 080812e4aa97a863d11826f71f65a933
> HCI Event: Command Complete (0x0e) plen 10
      Link Key Request Reply (0x01|0x000b) ncmd 1
        Status: Success (0x00)
        Address: C4:43:8F:A3:4D:83 (LG Electronics)
> HCI Event: Auth Complete (0x06) plen 3
        Status: PIN or Key Missing (0x06)
        Handle: 75
@ Authentication Failed: C4:43:8F:A3:4D:83 (0) status 0x05
< HCI Command: Disconnect (0x01|0x0006) plen 3
        Handle: 75
        Reason: Remote User Terminated Connection (0x13)
> HCI Event: Command Status (0x0f) plen 4
      Disconnect (0x01|0x0006) ncmd 1
        Status: Success (0x00)
> HCI Event: Disconnect Complete (0x05) plen 4
        Status: Success (0x00)
        Handle: 75
        Reason: Connection Terminated By Local Host (0x16)
@ Device Disconnected: C4:43:8F:A3:4D:83 (0) reason 4
Signed-off-by: NSzymon Janc <szymon.janc@codecoup.pl>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Trace EMAD messages going down to HW and up from HW. Devlink needs to be
registered before EMAD init so the trace function can be called
with valid devlink handle.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
v1->v2:
- Use trace_devlink_hwmsg directly
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define a tracepoint and allow user to trace messages going to and from
hardware associated with devlink instance.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following sparse warning:

net/dsa/dsa2.c:680:6: warning:
 symbol '_dsa_unregister_switch' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix missing clk_disable_unprepare() call before return
from dwceqos_probe() in the error handling case of invalid
fixed-link.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following sparse warnings:

drivers/net/ethernet/mediatek/mtk_eth_soc.c:79:5: warning:
 symbol '_mtk_mdio_write' was not declared. Should it be static?
drivers/net/ethernet/mediatek/mtk_eth_soc.c:98:5: warning:
 symbol '_mtk_mdio_read' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

security initialized after alloc workqueue, so we should exit security
before destroy workqueue in the error handing.

Fixes: 648af7fc ("rxrpc: Absorb the rxkad security module")
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PTR_ERR should access the value just tested by IS_ERR, otherwise
the wrong error code will be returned.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This script helps to create bonding network devices based on synthetic NIC
(the virtual network adapter usually provided by Hyper-V) and the matching
VF NIC (SRIOV virtual function). So the synthetic NIC and VF NIC can
function as one network device, and fail over to the synthetic NIC if VF is
down.

Mayjor distros (RHEL, Ubuntu, SLES) supported by Hyper-V are supported by
this script.
Signed-off-by: NHaiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

isr function issues SPI read command to mrf to obtain INTSTAT.
SPI transfer is 2 bytes, but value of 2nd byte is not defined.
This had the effect that only the first ISR worked as intended. The
second ISR read incorrect INTSTAT values. Observed on Raspberry PI B+.
Signed-off-by: NWalter Mack <wmack@componentsw.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The Makefile controlling compilation of this file is obj-y,
meaning that it currently is never being built as a module.

Since MODULE_ALIAS is a no-op for non-modular code, we can simply
remove the MODULE_ALIAS_NETPROTO variant used here.

We replace module.h with kmod.h since the file does make use of
request_module() in order to load other modules from here.

We don't have to worry about init.h coming in via the removed
module.h since the file explicitly includes init.h already.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=05 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3490 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/1600623Signed-off-by: NDmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

   drivers/net/dsa/b53/b53_srab.c: In function 'b53_srab_probe':
>> drivers/net/dsa/b53/b53_srab.c:388:20: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
      pdata->chip_id = (u32)of_id->data;
                       ^
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Kconfig currently controlling compilation of this code is:

init/Kconfig:config BPF_SYSCALL
init/Kconfig:   bool "Enable bpf() system call"

...meaning that it currently is not being built as a module by anyone.

Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.

Note that MODULE_ALIAS is a no-op for non-modular code.

We replace module.h with init.h since the file does use __init.

Cc: Alexei Starovoitov <ast@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

idx can be returned as -ENOSPC, so we should check for this first
before using it as an index into nn->vxlan_usecnt[] to avoid an
out of bounds array offset read.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable lan91x adapters in some ARM machines and models
when booted with an ACPI kernel.
Signed-off-by: NJeremy Linton <jeremy.linton@arm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some comments weren't updated to reflect the renaming of ndo's and the
change of arguments.
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Acked-by: NAlexander Duyck <aduyck@mirantis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As requested by Scott, removing him.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>