alloc_workqueue replaces deprecated create_workqueue().

A dedicated workqueue has been used since the workqueue
mlxsw_wq is used for FDB notif. processing with workitems that are
involved in normal device operation && because it's a network device
which can be depended upon during memory reclaim.

Workitems &trans->timeout_dw and &mlxsw_sp->fdb_notify.dw,
map to mlxsw_sp_fdb_notify_work (processes FDB notifications from the
underlying device and resolves the netdev to which the entry points to
and notifies the bridge using the switchdev notifier) and
mlxsw_emad_trans_timeout_work (provides async EMAD register access)
respectively. They require forward progress under memory pressure and
hence, WQ_MEM_RECLAIM has been set.

Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary here.
Signed-off-by: NBhaktipriya Shridhar <bhaktipriya96@gmail.com>
Tested-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

alloc_workqueue replaces deprecated create_workqueue().

A dedicated workqueue has been used since the workitem viz
(&lio->txq_status_wq.wk.work which maps to octnet_poll_check_txq_status)
is involved in a brief poll routine for checking transmit queue status
and is an intergral part of normal device operation.
WQ_MEM_RECLAIM has been set to guarantee forward progress under memory
pressure, which is a requirement here.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary.

flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty.
Signed-off-by: NBhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mlx4 RSS is limited to spread incoming packets to a power of two number
of queues.

An uniformly distibuted traffic would be split on queues 0 to N-1, N
being a power of two, each queue having a 1/N weight.

If number of RX queues is not a power of two, upper RX queues do not
receive traffic.

ethtool -x is lying, because it pretends some queues have higher weight.

Before patch:

lpaa24:~# ethtool -L eth1 rx 24
lpaa24:~# ethtool -x eth1
RX flow hash indirection table for eth1 with 24 RX ring(s):
    0:      0     1     2     3     4     5     6     7
    8:      8     9    10    11    12    13    14    15
   16:      0     1     2     3     4     5     6     7
RSS hash key:
e0:7c:3a:89:07:55:b6:58:69:cc:f4:e5:24:62:e3:25:88:6c:42:5b:d2:cb:9a:d2:e0:06:e1:dc:f9:09:a1:89:0f:a0:30:43:73:6f:0c:b6

If this information was correct, user space tools could expect queues 0
to 7 to receive twice more traffic than queues 8 to 15

After patch :

lpaa24:~# ethtool -L eth1 rx 24
lpaa24:~# ethtool -x eth1
RX flow hash indirection table for eth1 with 24 RX ring(s):
    0:      0     1     2     3     4     5     6     7
    8:      8     9    10    11    12    13    14    15
RSS hash key:
da:7b:09:60:f1:ac:67:b4:d0:72:d4:ec:a2:e5:80:0a:ad:50:22:1a:f8:f9:66:54:5f:22:45:c3:88:f4:57:82:c1:c1:90:ed:70:cb:40:ce
lpaa24:~# ethtool -X eth1 equal 8
lpaa24:~# ethtool -x eth1
RX flow hash indirection table for eth1 with 24 RX ring(s):
    0:      0     1     2     3     4     5     6     7
    8:      0     1     2     3     4     5     6     7
RSS hash key:
da:7b:09:60:f1:ac:67:b4:d0:72:d4:ec:a2:e5:80:0a:ad:50:22:1a:f8:f9:66:54:5f:22:45:c3:88:f4:57:82:c1:c1:90:ed:70:cb:40:ce
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NMaciej Żenczykowski <maze@google.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace netdev_alloc_skb_ip_align() with napi_alloc_skb() which can save
several CPU cycles by avoiding having to disable and re-enable IRQs.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: bgmac: Misc improvements

This patch series add minor changes to the bgmac driver:

- properly bind net_device with its backing device structure such that
  we can locate the device using common helper functions

- add support for ethtool statistics reading the HW MIB counters which
  is useful for debugging

- add netdev statistics throughout the TX/RX path to know what is going on
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a few netdev statistics to report transmitted and received bytes and
packets and a few obvious errors.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Read the statistics from the BGMAC's builtin MAC and return them to
user-space using the standard ethtool helpers.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for allowing different helpers to be utilized against
network devices created by the bgmac driver, make sure that we bind the
net_device with core->dev.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A draft version of the MTU Advice feature bit was specified as 25.  This
bit is not within the allowed range for network device feature bits, and
should be changed to be feature bit 3 to fully comply with the spec.

Fixes 14de9d11 ('virtio-net: Add initial MTU advice feature')
Signed-off-by: NAaron Conole <aconole@redhat.com>
Suggested-by: N"Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Frank Kellermann reported a kernel crash with 4.5.0 when IPv6 is
disabled at boot using the kernel option ipv6.disable=1. Using
current net-next with the boot option:

$ ip link add red type vrf table 1001

Generates:
[12210.919584] BUG: unable to handle kernel NULL pointer dereference at 0000000000000748
[12210.921341] IP: [<ffffffff814b30e3>] fib6_get_table+0x2c/0x5a
[12210.922537] PGD b79e3067 PUD bb32b067 PMD 0
[12210.923479] Oops: 0000 [#1] SMP
[12210.924001] Modules linked in: ipvlan 8021q garp mrp stp llc
[12210.925130] CPU: 3 PID: 1177 Comm: ip Not tainted 4.7.0-rc1+ #235
[12210.926168] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[12210.928065] task: ffff8800b9ac4640 ti: ffff8800bacac000 task.ti: ffff8800bacac000
[12210.929328] RIP: 0010:[<ffffffff814b30e3>]  [<ffffffff814b30e3>] fib6_get_table+0x2c/0x5a
[12210.930697] RSP: 0018:ffff8800bacaf888  EFLAGS: 00010202
[12210.931563] RAX: 0000000000000748 RBX: ffffffff81a9e280 RCX: ffff8800b9ac4e28
[12210.932688] RDX: 00000000000000e9 RSI: 0000000000000002 RDI: 0000000000000286
[12210.933820] RBP: ffff8800bacaf898 R08: ffff8800b9ac4df0 R09: 000000000052001b
[12210.934941] R10: 00000000657c0000 R11: 000000000000c649 R12: 00000000000003e9
[12210.936032] R13: 00000000000003e9 R14: ffff8800bace7800 R15: ffff8800bb3ec000
[12210.937103] FS:  00007faa1766c700(0000) GS:ffff88013ac00000(0000) knlGS:0000000000000000
[12210.938321] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[12210.939166] CR2: 0000000000000748 CR3: 00000000b79d6000 CR4: 00000000000406e0
[12210.940278] Stack:
[12210.940603]  ffff8800bb3ec000 ffffffff81a9e280 ffff8800bacaf8c8 ffffffff814b3135
[12210.941818]  ffff8800bb3ec000 ffffffff81a9e280 ffffffff81a9e280 ffff8800bace7800
[12210.943040]  ffff8800bacaf8f0 ffffffff81397c88 ffff8800bb3ec000 ffffffff81a9e280
[12210.944288] Call Trace:
[12210.944688]  [<ffffffff814b3135>] fib6_new_table+0x24/0x8a
[12210.945516]  [<ffffffff81397c88>] vrf_dev_init+0xd4/0x162
[12210.946328]  [<ffffffff814091e1>] register_netdevice+0x100/0x396
[12210.947209]  [<ffffffff8139823d>] vrf_newlink+0x40/0xb3
[12210.948001]  [<ffffffff814187f0>] rtnl_newlink+0x5d3/0x6d5
...

The problem above is due to the fact that the fib hash table is not
allocated when IPv6 is disabled at boot.

As for the VRF driver it should not do any IPv6 initializations if IPv6
is disabled, so it needs to know if IPv6 is disabled at boot. The disable
parameter is private to the IPv6 module, so provide an accessor for
modules to determine if IPv6 was disabled at boot time.

Fixes: 35402e31 ("net: Add IPv6 support to VRF device")
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify the RxRPC connect() implementation.  It will just note the
destination address it is given, and if a sendmsg() comes along with no
address, this will be assigned as the address.  No transport struct will be
held internally, which will allow us to remove this later.

Simplify sendmsg() also.  Whilst a call is active, userspace refers to it
by a private unique user ID specified in a control message.  When sendmsg()
sees a user ID that doesn't map to an extant call, it creates a new call
for that user ID and attempts to add it.  If, when we try to add it, the
user ID is now registered, we now reject the message with -EEXIST.  We
should never see this situation unless two threads are racing, trying to
create a call with the same ID - which would be an error.

It also isn't required to provide sendmsg() with an address - provided the
control message data holds a user ID that maps to a currently active call.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFabien Siron <fabien.siron@epita.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I am not sure mlx4_en_netpoll() is doing anything useful right now.

mlx4 has different NAPI structures for RX and TX, and netpoll only wants
to drain TX queues.

Lets schedule NAPI polls on TX, not RX.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: Broadcom BCM53xx switches support

This patch series adds support for the Broadcom BCM53xx series aka RoboSwitches.

This driver is largely based on Jonas Gorski's b53 driver for OpenWrt which can
be found here:

https://dev.openwrt.org/browser/trunk/target/linux/generic/files/drivers/net/phy/b53

a few bug fixes and DSA-ifycation later, here is what we got.

This has been successfully tested in the following configurations:

- Broadcom BCM53011 using the SRAB bus layer with 4 ports LAN, 1 port WAN

- A Broadcom BCM7445 device with an internal Starfighter 2 switch (bcm_sf2.c)
  and a Broadcom BCM53125 hanging off one of its ports connected via MDIO, creating
  two trees hanging off each other, and this works!

- A Broadcom BCM53125 MDIO connected to a Lamobo/Bananapi R1 board using the STMMAC
  MDIO driver

For now, we do not enable Broadcom tags, because there are different
generations of switches being supported which have different tag formats, but
the plan is to enable them later on.

Support for different HW features will be added later: EEE, Compact Field
Processor (TCAM) once this initial cut gets accepted.

Testing and bug reports welcome!
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for configuration VLANs on B53 devices by implementing the
port VLAN add/del/dump functions. We currently default to a behavior
which is equivalent to having VLAN filtering turned on, where all VLANs
not programmed into the VLAN port-based vector will be discarded on
ingress.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for HW bridging by tying the ports together in the same port
VLAN mask when they belong to the same bridge, and isolating them to be
alone with the CPU port when they are not.

Propagate STP states from the bridge layer to the switch's HW mapping
when requested.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds support for FDB add/delete/dump using the ARL read/write logic and
the ARL search logic for faster dumps. The code is made flexible enough
it could support devices with a different register layout like BCM5325
and BCM5365 which have fewer number of entries or pack values into a
single 64 bits register.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Broadcom BCM7445 STB chip has an issued in its revision D0 which was
previously worked around in drivers/net/dsa/bcm_sf2.c where we may
end-up double programming the integrated BCM7445 switch (bcm_sf2) and an
external Broadcom switch such as BCM53125, since these are mostly
register compatible.

Add a small quirk which just defers probing until we are sitting on the
slave DSA MDIO bus, which will allow us to intercept reads/writes and
funnel them through the SF2 internal MDIO master (which happens to
disconnect its pseudo PHY).
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for Broadcom's BCM53xx switch family, also known
as RoboSwitch. Some of these switches are ubiquituous, found in home
routers, Wi-Fi routers, DSL and cable modem gateways and other
networking related products.

This drivers adds the library driver (b53_common.c) as well as a few bus
glue drivers for MDIO, SPI, Switch Register Access Block (SRAB) and
memory-mapped I/O into a SoC's address space (Broadcom BCM63xx/33xx).

Basic operations are supported to bring the Layer 1/2 up and running,
but not much more at this point, subsequent patches add the remaining
features.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: bcm_sf2: add VLAN support

This is long overdue, finally add support for VLANs in the Broadcom Starfigther
2 switch driver.

There are a few things that make us differ from e.g; mv88e6xxx.c:

- we keep a software cache of which VLANs are enabled and which are not to
  dramatically speed up the VLAN dump operation, we do not have any HW operation
  which would only return the list of valid VLAN entries, they would have to be
  all queried one by one, with 4K vlans, this takes a while

- the default behavior is equivalent to setting VLAN filtering to 1, still working
  on implementing a proper port_vlan_filtering callback, but I figured the most
  conservative behavior is probably okay anyway

- without enabling VLANs, the default behavior is to receive any 802.1q frames
  (per the DSA documentation), however, once we start enabling VLAN support, if
  an interface leaves the bridge, we still want it to receive all 802.1q frames
  so we utiliez the "Join all VLAN" feature of the switch to perform that
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for configuring VLANs on the Broadcom Starfigther2 switch.
This is all done through the bridge vlan facility just like other DSA
drivers.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the definitions for the VLAN registers that we are going to
manipulate in subsequent patches.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Re-order the bcm_sf2_sw_setup() function so that it is at the far end of
the driver to avoid any kind of forward declarations.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a helper function to fast age something that is controlled by the
caller: port, VLAN. We will use this to implement a VLAN fast age
operation.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net: better lockdep annotations

Introduction of qdisc->running seqcount added lockdep false positives.

While chasing the bug, it came to me that we had a lot of copies of the
same stuff in virtual drivers.

This patch series has the qdisc->running fix (considers that a trylock
is attempted in lockdep terminology), and adds a generic helper so
that we no longer have to patch many virtual drivers when a new per-device
or per-qdisc lock is added.

Thanks to David Ahern for reporting the issue and testing my patches :)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case a qdisc is used on a ipvlan device, we need to use different
lockdep classes to avoid false positives.

Use the new netdev_lockdep_set_classes() generic helper.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case a qdisc is used on a macvlan device, we need to use different
lockdep classes to avoid false positives.

Use the new netdev_lockdep_set_classes() generic helper.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case a qdisc is used on a vrf device, we need to use different
lockdep classes to avoid false positives.

Use the new netdev_lockdep_set_classes() generic helper.
Reported-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Tested-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is time to add netdev_lockdep_set_classes() helper
so that lockdep annotations per device type are easier to manage.

This removes a lot of copies and missing annotations.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) qdisc_run_begin() is really using the equivalent of a trylock.
  Instead of using write_seqcount_begin(), use a combination of
  raw_write_seqcount_begin() and correct lockdep annotation.

2) sch_direct_xmit() should use regular spin_lock(root_lock)

Fixes: f9eb8aea ("net_sched: transform qdisc running bit into a seqcount")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I'm hitting 5 second timeout in rndis_filter_set_rss_param() while setting
RSS parameters for the device. When this happens we end up returning
-ETIMEDOUT from the function and rndis_filter_device_add() falls back to
setting

        net_device->max_chn = 1;
        net_device->num_chn = 1;
        net_device->num_sc_offered = 0;

but after a moment the rndis request succeeds and subchannels start to
appear. netvsc_sc_open() does unconditional nvscdev->num_sc_offered-- and
it becomes U32_MAX-1. Consequent rndis_filter_device_remove() will hang
while waiting for all U32_MAX-1 subchannels to appear and this is not
going to happen.

The immediate issue could be solved by adding num_sc_offered > 0 check to
netvsc_sc_open() but we're getting out of sync with the host and it's not
easy to adjust things later, e.g. in this particular case we'll be creating
queues without a user request for it and races are expected. Same applies
to other parts of the driver which have the same completion timeout.

Following the trend in drivers/hv/* code I suggest we remove all these
timeouts completely. As a guest we can always trust the host we're running
on and if the host screws things up there is no easy way to recover anyway.
Signed-off-by: NVitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: NHaiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ipip6_tunnel_xmit() is called immediately after checking that
skb->protocol is  htons(ETH_P_IPV6) so there is no need
to check it a second time.

Found by inspection.
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NDinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Westphal says:

====================
sched, cbq: remove OVL_STRATEGY/POLICE support

iproute2 does not implement any options that result in the
TCA_CBQ_OVL_STRATEGY/TCA_CBQ_POLICE attributes being set/used.

This series removes these two attributes from cbq and makes kernel reject
 them via EOPNOTSUPP in case they are present.

The two followup changes then remove several features from qdisc
infrastructure that are then no longer used/needed.  These are:
 - The 'drop' method provided by most qdiscs
 - the 'reshape_fail' function used by some qdiscs
 - the __parent member in struct Qdisc

I tested this with allmod and allyesconfig builds and also with
a brief cbq script:

  tc qdisc add dev eth0 root handle 1:0 cbq bandwidth 10Mbit avpkt 1000 cell 8
  tc class add dev eth0 parent 1:0 classid 1:1 est 1sec 8sec cbq bandwidth 10Mbit rate 5Mbit prio 1 allot 1514 maxburst 20 cell 8 avpkt 1000 bounded split 1:0 defmap 3f
  tc class add dev eth0 parent 1:0 classid 1:2 est 1sec 8sec cbq bandwidth 10Mbit rate 5Mbit prio 1 allot 1514 maxburst 20 cell 8 avpkt 1000 bounded split 1:0 defmap 3f
  tc filter add dev eth0 parent 1:0 protocol ip prio 1 u32 match ip tos 0x10 0xff classid 1:1 police rate 2Mbit burst 10K reclassify
  tc filter add dev eth0 parent 1:0 protocol ip prio 1 u32 match ip tos 0x0c 0xff classid 1:2
  tc filter add dev eth0 parent 1:0 protocol ip prio 2 u32 match ip tos 0x10 0xff classid 1:2
  tc filter add dev eth0 parent 1:0 protocol ip prio 3 u32 match ip tos 0x0 0x0 classid 1:2

No changes since v1 except patch #5 to fix up struct Qdisc layout.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Earlier commits removed two members from struct Qdisc which places
next_sched/gso_skb into a different cacheline than ->state.

This restores the struct layout to what it was before the removal.
Move the two members, then add an annotation so they all reside in the
same cacheline.

This adds a 16 byte hole after cpu_qstats.

The hole could be closed but as it doesn't decrease total struct size just
do it this way.
Reported-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

after removal of TCA_CBQ_OVL_STRATEGY from cbq scheduler, there are no
more callers of ->drop() outside of other ->drop functions, i.e.
nothing calls them.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the removal of TCA_CBQ_POLICE in cbq scheduler qdisc->reshape_fail
is always NULL, i.e. qdisc_rehape_fail is now the same as qdisc_drop.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

iproute2 doesn't implement any cbq option that results in this attribute
being sent to kernel.

To make use of it, user would have to

- patch iproute2
- add a class
- attach a qdisc to the class (default pfifo doesn't work as
  q->handle is 0 and cbq_set_police() is a no-op in this case)
- re-'add' the same class (tc class change ...) again
- user must also specifiy a defmap (e.g. 'split 1:0 defmap 3f'), since
  this 'police' feature relies on its presence
- the added qdisc must be one of bfifo, pfifo or netem

If all of these conditions are met and _some_ leaf qdiscs, namely
p/bfifo, netem, plug or tbf would drop a packet, kernel calls back into
cbq, which will attempt to re-queue the skb into a different class
as indicated by the parents' defmap entry for TC_PRIO_BESTEFFORT.

[ i.e. we behave as if tc_classify returned TC_ACT_RECLASSIFY ].

This feature, which isn't documented or implemented in iproute2,
and isn't implemented consistently (most qdiscs like sfq, codel, etc
drop right away instead of attempting this reclassification) is the
sole reason for the reshape_fail and __parent member in Qdisc struct.

So remove TCA_CBQ_POLICE support from the kernel, reject it via EOPNOTSUPP
so userspace knows we don't support it, and then remove no-longer needed
infrastructure in followup commit.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

since initial revision of cbq in 2004 iproute 2 has never implemented
support for TCA_CBQ_OVL_STRATEGY, which is what needs to be set to
activate the class->drop() call (TC_CBQ_OVL_DROP strategy must be
set by userspace value must be set by userspace).

David Miller says:
   It seems really safe to kill this thing off, flag an error if someone
   tries to set the attribute, and therefore kill off all of the
   non-default cbq_ovl_*() functions.

A followup commit can then remove all .drop qdisc methods since this
removed the only caller.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ip6 GRE tap device should not be forced to down state to change
the mac address and should allow live address change for tap device
similar to ipv4 gre.
Signed-off-by: NShweta Choudaha <schoudah@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David Ahern says:

====================
net: vrf: Improve use of FIB rules

Currently, VRFs require 1 oif and 1 iif rule per address family per
VRF. As the number of VRF devices increases it brings scalability
issues with the increasing rule list. All of the VRF rules have the
same format with the exception of the specific table id to direct the
lookup. Since the table id is available from the oif or iif in the
loopup, the VRF rules can be consolidated to a single rule that pulls
the table from the VRF device.

This solution still allows a user to insert their own rules for VRFs,
including rules with additional attributes. Accordingly, it is backwards
compatible with existing setups and allows other policy routing as
desired.

Hopefully v5 is the charm; my e-waste can is getting full.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>