Energy Efficient Ethernet on 82579 and I217 should only be enabled if not
disabled by the user, if the link is full duplex and the link partner has
similar EEE capabilities (stored in different EMI registers on the two
different parts).

After enabling EEE, read the IEEE MMD register 3.1 (which is also stored in
different EMI registers on the two different parts) to clear the count of
received Tx/Rx LPI indications.

Also, rename I217_EEE_100_SUPPORTED to I82579_EEE_100_SUPPORTED to indicate
the bit is valid starting with I82579 (released before I217).
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When connected to certain switches, the 82577 PHY might drop link
unexpectedly.  Work around the issue by setting the Mean Square Error
higher than the hardware default.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The Extended Management Interface (EMI) registers are accessed by first
writing the EMI register offset to the EMI_ADDR regiter and then either
reading or writing the data to/from the EMI_DATA register.  Add helper
functions for performing these steps and convert existing EMI register
accesses accordingly.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On I217, the bit that indicates an invalid EEPROM (NVM) image checksum has
changed from previous ICH/PCH LOMs.  When validating the EEPROM checksum,
check the appropriate bit on different devices.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When data blocks are written to the EEPROM, the HW/SW/FW semaphore must be
held for the duration.  With large data blocks on 80003es2lan, 82571 and
82572, this can take too long and cause the firmware to take ownership of
the semaphore and consequently ownership of writes to the EEPROM.
Instead, acquire and release the semaphore for each page of the block
written.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Enables flow control to be set in SerDes autoneg mode. This is what is
done for copper, but relies on a different set of register/bit checks
since this is all done within the Mac registers.

Remove inapplicable comment in defines.h
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since submit 621b4d66 the bnx2x driver support FW GRO.
However, when using the device with GRO enabled in bridging
scenarios throughput is very low, as the bridge expects all
incoming packets to be passed with CHECKSUM_PARTIAL -
a demand which is satisfied by the SW GRO implementation,
but was missed in the bnx2x driver implementation (which returned
CHECKSUM_UNNECESSARY).

Now, given that the traffic is supported by FW GRO (TCP/IP),
the bnx2x driver calculates the pseudo checksum by itself,
passing skbs with CHECKSUM_PARTIAL and giving a much better
throughput when receiving GRO traffic.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When enabling interrupts, acknowledge the interrupt only
after configuring the IGU to the correct interrupt mode
(otherwise it would dirty selftests)
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get better control over interrupts during panic, and allow FW to
test outgoing Tx packets when stop-on-error is allowed.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This revises and enhances the bnx2x register dump facilities,
adding support for `ethtool -w' on top of `ethtool -d'.
Signed-off-by: NMiriam Shitrit <miris@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a device is configured to act as either iscsi or fcoe
device in its nvram, prevent the other from being misused by
preventing its activation in the driver.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On rare occasions, self test link may fail since the link is
being sampled while it's still being stabilized.
To correct this behaviour, try to sample the link for 2 seconds
prior to declaring a failure.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current logic causes chips running in switch dependent multi-function
FCoE mode not to configure their MAC, leading to an all 0s MAC.

This patch configures the interface with the SAN Mac instead.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Self-tests following boot from SAN have failed as the
UNDI driver might leave some NIG interrupt indications.

This patch does the clean-up, clearing those indications
and allowing the test to pass.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	Documentation/networking/ip-sysctl.txt
	drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c

Both conflicts were simply overlapping context.

A build fix for qlcnic is in here too, simply removing the added
devinit annotations which no longer exist.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TG3_PHY_AUXCTL_SMDSP_ENABLE/DISABLE macros do a blind write to the phy
auxiliary control register and overwrite the EXT_PKT_LEN (bit 14) resulting
in intermittent crc errors on jumbo frames with some link partners. Change
the code to do a read/modify/write.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When netconsole is enabled, logging messages generated during tg3_open
can result in a null pointer dereference for the uninitialized tg3
status block. Use the irq_sync flag to disable polling in the early
stages. irq_sync is cleared when the driver is enabling interrupts after
all initialization is completed.
Signed-off-by: NNithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit a5e371f6 ("drivers/net: delete
all code/drivers depending on CONFIG_MCA") most of the MCA drivers went,
including the Kconfig/Makefile hooks for ibmlana, but it seems that I
missed the "git rm" on these actual driver files, and with the namespace
overlap with machine check architecture, it got missed by various git
grep type checking done at that time.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
The following patchset contains netfilter fixes for 3.8-rc3,
they are:

* fix possible BUG_ON if several netns are in use and the nf_conntrack
  module is removed, initial patch from Gao feng, final patch from myself.

* fix unset return value if conntrack zone are disabled at
  compile-time, reported by Borislav Petkov, fix from myself.

* fix display error message via dmesg for arp_tables, from Jan Engelhardt.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch corrects some problems with LSM/SELinux that were introduced
with the multiqueue patchset.  The problem stems from the fact that the
multiqueue work changed the relationship between the tun device and its
associated socket; before the socket persisted for the life of the
device, however after the multiqueue changes the socket only persisted
for the life of the userspace connection (fd open).  For non-persistent
devices this is not an issue, but for persistent devices this can cause
the tun device to lose its SELinux label.

We correct this problem by adding an opaque LSM security blob to the
tun device struct which allows us to have the LSM security state, e.g.
SELinux labeling information, persist for the lifetime of the tun
device.  In the process we tweak the LSM hooks to work with this new
approach to TUN device/socket labeling and introduce a new LSM hook,
security_tun_dev_attach_queue(), to approve requests to attach to a
TUN queue via TUNSETQUEUE.

The SELinux code has been adjusted to match the new LSM hooks, the
other LSMs do not make use of the LSM TUN controls.  This patch makes
use of the recently added "tun_socket:attach_queue" permission to
restrict access to the TUNSETQUEUE operation.  On older SELinux
policies which do not define the "tun_socket:attach_queue" permission
the access control decision for TUNSETQUEUE will be handled according
to the SELinux policy's unknown permission setting.
Signed-off-by: NPaul Moore <pmoore@redhat.com>
Acked-by: NEric Paris <eparis@parisplace.org>
Tested-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new permission to align with the new TUN multiqueue support,
"tun_socket:attach_queue".

The corresponding SELinux reference policy patch is show below:

 diff --git a/policy/flask/access_vectors b/policy/flask/access_vectors
 index 28802c5..a0664a1 100644
 --- a/policy/flask/access_vectors
 +++ b/policy/flask/access_vectors
 @@ -827,6 +827,9 @@ class kernel_service

  class tun_socket
  inherits socket
 +{
 +       attach_queue
 +}

  class x_pointer
  inherits x_device
Signed-off-by: NPaul Moore <pmoore@redhat.com>
Acked-by: NEric Paris <eparis@parisplace.org>
Tested-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

spin_is_locked() on a non !SMP build is kind of useless.

BUG_ON(!spin_is_locked(xx)) is guaranteed to crash.

Just remove this check in reqsk_fastopen_remove() as
the callers do hold the socket lock.
Reported-by: NKetan Kulkarni <ketkulka@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Dave Taht <dave.taht@gmail.com>
Acked-by: NH.K. Jerry Chu <hkchu@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull devicetree fixes from Rob Herring:
 "Two fixes to prevent unconditional re-compile of dts files on arm and
  arm64."

* tag 'dt-fixes-for-3.8' of git://sources.calxeda.com/kernel/linux:
  ARM: dts: prevent *.dtb from always being rebuilt
  arm64: dts: prevent *.dtb from always being rebuilt

Andrew Morton pointed this out a month ago, and then I completely forgot
about it.

If we read a partial last page of a block device, we will zero out the
end of the page, but since that page can then be mapped into user space,
we should also make sure to flush the cache on architectures that have
virtual caches.  We have the flush_dcache_page() function for this, so
use it.

Now, in practice this really never matters, because nobody sane uses
virtual caches to begin with, and they largely exist on old broken RISC
arhitectures.

And even if you did run on one of those obsolete CPU's, the whole "mmap
and access the last partial page of a block device" behavior probably
doesn't actually exist.  The normal IO functions (read/write) will never
see the zeroed-out part of the page that migth not be coherent in the
cache, because they honor the size of the device.

So I'm marking this for stable (3.7 only), but I'm not sure anybody will
ever care.
Pointed-out-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: stable@vger.kernel.org  # 3.7
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ifb should lookup devices in the appropriate namespace.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: NKosta Zertsekel <konszert@marvell.com>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet pointed out that act_mirred needs to find the current net_ns,
and struct net pointer is not provided in the call chain.  His original
patch made use of current->nsproxy->net_ns to find the network namespace,
but this fails to work correctly for userspace code that makes use of
netlink sockets in different network namespaces.  Instead, pass the
"struct net *" down along the call chain to where it is needed.

This version removes the ifb changes as Eric has submitted that patch
separately, but is otherwise identical to the previous version.
Signed-off-by: NBenjamin LaHaise <bcrl@kvack.org>
Tested-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only user is cxgb3 driver.

old_neigh is used to check device change, but it must not happen
on redirect.  In this sense, we can remove old_neigh argument.
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull sound fixes from Takashi Iwai:
 "Most of commits found here are for ASoC device specific fixes,
  arizona, cs4271, wm5102, wm2200, etc, in addition to a couple of
  memory leak fixes in ASoC core.

  Other than that, regression fixes in HD-audio and USB-audio, and a fix
  for new Realtek codecs."

* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (30 commits)
  ALSA: usb-audio: Fix NULL dereference by access to non-existing substream
  ALSA: hda - Add support of new codec ALC284
  ALSA: usb-audio: Make ebox44_table static
  ALSA: hdspm - Fix wordclock status on AES32
  Revert "ALSA: hda - Shut up pins at power-saving mode with Conexnat codecs"
  ALSA: hda - Disable runtime D3 for Intel CPT & co
  ALSA: pxa27x: fix ac97 warm reset
  ALSA: pxa27x: fix ac97 cold reset
  ASoC: wm_adsp: Ensure that block writes are from DMA aligned addresses
  ASoC: wm2000: Fix sense of speech clarity enable
  ASoC: wm5100: Remove DSP B and left justified formats
  ASoC: arizona: Remove DSP B and left justified AIF modes
  ASoC: wm2200: Remove DSP B and left justified AIF modes
  ASoC: wm5102: Improve speaker enable performance
  ASoC: core: fix the memory leak in case of remove_aux_dev()
  ASoC: core: fix the memory leak in case of device_add() failure
  ASoC: cs42l52: Catch no-match case in cs42l52_get_clk
  ASoC: lm49453: Update lm49453_reg_defs values as per LM49453 HW revision-B
  ASoC: lm49453: Fix adc, mic and sidetone volume ranges
  ASoC: arizona: Correct FLL source definitions
  ...

The removal of the 8390 EISA drivers actually comprises the
complete content of the EISA probe block, so we can now remove
that block, and its hook into the unified probe.  Note that
the deleted comment mentions PCI probes, but they long since
moved elsewhere, so no PCI probes are touched here.

We get rid of the orphaned EISA probe prototypes, and a couple
of left over MCA probe prototypes at the same time.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ipv6_prefix_equal() just casts its arguments and it is the only
user of __ipv6_prefix_equal().
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce __ipv6_addr_diff64() to to find the first different
bit between two addresses on 64bit architectures.

32bit version is still available as __ipv6_addr_diff32(),
and __ipv6_addr_diff() automatically selects appropriate
version.
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull staging fixes from Greg Kroah-Hartman:
 "Here are a number of small fixes to staging drivers for your 3.8-rc3
  tree.

  Well, the omapdrm fixes aren't really "small" but they were waiting on
  a number of other drm patches to go in through the drm tree, and got
  delayed by my vacation over the holidays.  They are totally
  self-contained, everyone involved have acked them, and they fix issues
  that people have been having with the driver.

  Other than that one, it's a bunch of tiny bugfixes for a number of
  reported issues.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'staging-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (36 commits)
  staging: zram: fix invalid memory references during disk write
  staging: tidspbridge: use prepare/unprepare on dsp clocks
  staging: tidspbridge: Fix build breakage due to splitting CM functions.
  staging: comedi: comedi_test: fix race when cancelling command
  staging: comedi: Kconfig: COMEDI_NI_AT_A2150 should select COMEDI_FC
  staging: comedi: prevent auto-unconfig of manually configured devices
  staging: comedi: fix minimum AO period for NI 625x and NI 628x
  staging: vme_pio2: fix oops on module unloading
  staging: speakup: avoid out-of-range access in synth_add()
  staging: speakup: avoid out-of-range access in synth_init()
  staging: rtl8192e: Fix failure to check pci_map_single()
  staging: rtl8187se: Fix failure to check pci_map_single()
  staging: drm/imx: fix double free bug in error path
  staging: drm/imx: several bug fixes
  staging: drm/imx: check return value of ipu_reset()
  staging: drm/omap: fix flags in dma buf exporting
  staging: drm/omap: use omapdss low level API
  staging/fwserial: Update TODO file per reviewer comments
  staging/fwserial: Limit tx/rx to 1394-2008 spec maximum
  staging/fwserial: Refine Kconfig help text
  ...

Pull USB fixes from Greg Kroah-Hartman:
 "Here are a bunch of USB fixes for your 3.8-rc3 tree.  They all either
  fix problems that have been reported (like the xhci/hub changes) or
  add new device ids to existing drivers.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'usb-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (39 commits)
  usb: ftdi_sio: Crucible Technologies COMET Caller ID - pid added
  usb: host: ohci-tmio: fix compile warning
  USB: Add device quirk for Microsoft VX700 webcam
  USB: ehci-fsl: fix regression on mpc5121e
  usb: chipidea: Allow disabling streaming not only in udc mode
  USB: fsl-mph-dr-of: fix regression on mpc5121e
  USB: select USB_ARCH_HAS_EHCI for MXS
  USB: hub: handle claim of enabled remote wakeup after reset
  USB: cdc-acm: Add support for "PSC Scanning, Magellan 800i"
  USB: option: add Nexpring NP10T terminal id
  USB: option: add Telekom Speedstick LTE II
  USB: option: blacklist network interface on ZTE MF880
  usb: imx21-hcd: Include missing linux/module.h
  USB: option: Add new MEDIATEK PID support
  USB: ehci: make debug port in-use detection functional again
  USB: usbtest: fix test number in log message
  xhci: Avoid "dead ports", add roothub port polling.
  USB: Handle warm reset failure on empty port.
  USB: Ignore port state until reset completes.
  USB: Increase reset timeout.
  ...