This device claims TSO and checksum support for vlans.  It also
allows a user to control vlan acceleration offloading.  As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO and hw checksums.

In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This results in corrupted frames sent on the wire.

This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.

Fix this by using vlan_get_protocol() helper.

CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device claims TSO and checksum support for vlans.  It also
allows a user to control vlan acceleration offloading.  As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.

In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This will results in corrupted frames sent on the wire.

This patch extract the protocol value correctly and corrects TSO
for non-accelerated traffic.

CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device claims  TSO support for vlans.  It also allows a
user to control vlan acceleration offloading.  As such, it is
possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.

In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO information.  This results
in corrupted frames sent on the wire.  Corruptions include
incorrect IP total length and invalid IP checksum.

This patch extract the protocol value correctly and corrects TSO
for non-accelerated traffic.

CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The receive hang detection routine was never being run when
PTP was enabled.

Change-ID: I200f35b0f3190d31b595df89d678f4c8a2131ba0
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In some functions we might be doing potential dereference
without a check. This patch puts the check in place for all these
functions. Also fix the "for loops" so that we increment VF at the
right place so that we always do it even if we are short-circuiting
the loop through continue.

Change-ID: Id4276cfb1e841031bb7b6d6790c414242f364a9f
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Whenever we get a Tx hang we issue a PFR, which means we send AQ
messages to VFS about the reset coming. Unfortunately with the recent
fix to be able to send messages to all VFS which earlier was not
happening at all we now are sending messages to not just the VFS that
are up but also to VFS that are not up.  AQ complains about this and
sends us an error in ARQ called LAN overflow event for a queue. We
check if the queue belongs to a VF and if it does we try to send a
vc_notify_vf_reset message to that VF. Well if the VF is not up/enabled
we will be entering this function with a non-active VF id. In this
function we were assuming VF struct is populated but it won't be if
the VF is not active.

Change-ID: Ic6733cda4582d3609fe6d83b2872bb2dcdc73f4a
Signed-off-by: NAshish N Shah <ashish.n.shah@intel.com>
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines.  This issue was reported by checkpatch.

A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):

// <smpl>

@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@

- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;

// </smpl>

[bhelgaas: add semantic patch]
Signed-off-by: NBenoit Taine <benoit.taine@lip6.fr>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

There is an excessive space character between the word and the
period in the debug message. So delete it.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The macro E1000_success is meant to be E1000_SUCCESS. As the return
statement in the function is good as is, let's simply correct the
comment for this trivial matter.

Additionally E1000_ERR_HOST_INTERFACE_COMMAND is supposed to be
-E1000_ERR_HOST_INTERFACE_COMMAND.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Tested-By: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Correct typo in the name of the type given to sizeof.  Because it is the
size of a pointer that is wanted, the typo has no impact on compilation or
execution.

This problem was found using Coccinelle (http://coccinelle.lip6.fr/).  The
semantic patch used can be found in message 0 of this patch series.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Tested-By: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fixes the following sparse warnings:

drivers/net/ethernet/intel/i40e/i40e_nvm.c:254:13: warning:
 symbol 'i40e_write_nvm_aq' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Tested-By: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix missing include in Intel i40e driver. Without this include linux next
tree won't compile.
Signed-off-by: NLucas Tanure <tanure@linux.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

All other add functions for lists have the new item as first argument
and the position where it is added as second argument.  This was changed
for no good reason in this function and makes using it unnecessary
confusing.

The name was changed to hlist_add_behind() to cause unconverted code to
generate a compile error instead of using the wrong parameter order.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NKen Helias <kenhelias@firemail.de>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>	[intel driver bits]
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Removing VF driver during device still in reset caused guest OS panic.

in the i40evf_remove(), we're trying to clean mac_filter_list which has
not been initialized since the device is still stuck at the reset.
The change is to initialize the filter_list before setting any task.

Change-ID: I8b59df7384416c7e6f2d264b598f447e1c2c92b0
Signed-off-by: NSerey Kong <serey.kong@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the driver is loaded and then unloaded before the interface is
brought up, then it will allocate a MAC filter entry and never free it.
To fix this, on unload, run through the mac filter list and free all the
entries. We also do this during reset recovery when the driver cannot
contact the PF and needs to shut down completely.

Change-ID: I15fabd67eb4a1bfc57605a7db60d0b5d819839db
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a memory leak. Driver was allocating memory for queue vectors on
init but not freeing them on shutdown. These need to be freed at two
different times: during module unload, and during reset recovery when
the driver cannot contact the PF driver and needs to give up.

Change-ID: I7c1d0157a776e960d4da432dfe309035aad7c670
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add in an adapter state check to prevent re-arming watchdog timer after
i40evf_remove has been called and timer has been deleted.

Change-ID: I636ba7c6322be8cbf053231959f90c0a2d8d803a
Signed-off-by: NAshish Shah <ashish.n.shah@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously defined state I40E_VFR_VFACTIVE uses bit 1 which is now set to
"reserved."  Update the state checks to also include I40E_VFR_COMPLETED.
This change will allow the VF to work with both existing and future PFs.

Change-ID: Ifd1d34f79f3b0ffd6d2550ee4dadc55825ff52f8
Signed-off-by: NAshish Shah <ashish.n.shah@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the ability of a VF to set unicast promiscuous mode.
Considered to be a security risk to allow VFs to receive traffic
intended for other VFs so don't allow it, simply ignore the flag.

Also fix it to send the correct seid to aq for multicast promiscuous set.

Change-ID: Icb9c49a281a8e9d3aeebf991ef1533ac82b84b14
Signed-off-by: NAshish Shah <ashish.n.shah@intel.com>
Tested-by: NJim Young  <jamesx.m.young@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes comment for reset reason

Change-ID: I6fda4fa292255e6eb0f874502b4d38d722149b10
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver was converted to use snprintf everywhere but this one function.
Just use snprintf, instead of sprintf.

Also a small spelling correction in a comment.

Change-ID: I59d45f94a52754c7b4cd6034df9a61d8132b7f77
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The local loopback should only be enabled for VSIs that are supporting
cascaded VEBs or VEPA setups.  This is not the case here, and we need
to stop the VEB from echoing the VMDQ VSI packets back at the VSI.

Change-ID: I9dfb6ac79db24d04360d7efde62d81e20abc5090
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vf_id needs to be offset by the vf_base_id from hw function capabilities
for the case of multiple PFs.

Change-ID: I20ca8621f98e9cdf98649380b8eeaa35db52677c
Signed-off-by: NAshish Shah <ashish.n.shah@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the HW registers are no longer in debug mode and many are
locked down for writes, we need to expose the Firmware API request
used to do writes on the driver's behalf.

Change-ID: I09a05c4dc9ea0b24c00193faac34d7799eaa8496
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds newly added FCoE files to the build but only if FCoE module is configured.

Also, updates i40e document for added FCoE support.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds FCoE specific code to existing i40e core driver to:-

1. have separate FCoE VSI with additional FCoE queues pairs.
2. have FCoE related hash defines.
3. have additional FCoE related stats code.
4. export and then re-use existing functions required by FCoE build.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds FCoE ( Fibre Channel Over Ethernet ) code for
Intel XL710 adapters. This patch is limited to only new FCoE
offloads code in newly added files by this patch and then
following patches in the series modifies rest of the existing
driver to enable FCoE with i40e driver.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Tested-by: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding a function, and associated calls, to flush writes to (read) the LPIC
MAC register before entering the shutdown flow.  This fixes the problem
of the PHY never negotiating a 100M link (if both sides of the link support
EEE and 100M link) when Runtime PM is enabled.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The process of shutting down the system causes a call to the close PM
callback.  The reset in close causes a loss of link, and the resultant
LSC interrupt causes the Runtime PM idle callback to be called.  The
check for link (while link is down) in the idle callback is wiping the
information about the EEE ability of the link partner.  The information is
still gone when the PHY is powered back up in the shutdown flow.  This
causes EEE in S5 to fail when Runtime PM is active.

Save the link partner's EEE ability in the idle callback so that a Runtime
PM event will not cause a loss of this information.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On I217 and newer hardware, EEE is enabled in the PHY by the software
when link is up and disabled by the hardware when link is lost.

To enable EEE in Sx (When both ends of the link support, and are enabled
for, EEE and 100Mbps), we need to disable LPLU and configure the PHY to
automatically enable EEE when link is up, since there will be no software
to complete the task.

To configure this in the PHY, the Auto Enable LPI bit in the Low Power
Idle GPIO Control register must be set.  For normal operation in S0, this
bit must be cleared.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Adding code to check and respond to previously ignored return values
from NVM access functions.

Issue discovered through static analysis.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Modifying the jumbo frame workaround for 82579, i217 and i218 client parts
to increase the gap between the read and write pointers in the Tx FIFO.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make return values more direct, eliminating some gotos and
otherwise unneeded conditionals. This also eliminates some
local variables. Also a few minor cleanups in affected code
so checkpatch won't complain.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

All of the code involved with returning the supported physical
layer is actually unused, so delete it.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If ixgbe_write_mbx is called and no mbx->ops.write method
exists, no error code is returned. The corresponding read
function explicitly returns an error in such a case as do
other functions, so this appears to be a minor bug. Fix
it for consistency, and generate return values directly
to make things clearer.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In the function ixgbe_get_swfw_sync_semaphore, an incorrect
check was treating success as failure and vice-versa. This led
to manipulating the IXGBE_SWFW_SYNC register without holding
the software semaphore first, which is an error. In addition,
if getting the REGSMP bit in the IXGBE_SW_FW_SYNC register
timed out, no error code would be returned, making the caller
think that it had successfully acquired the lock. Fix both of
those issues and clean up the function a bit, such as make the
name in the comment match the function.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Failure to acquire the semaphore would lead to a spurious release
of the semaphore in several functions. Do not release a semaphore
that you did not get.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Convert some udelay calls to the preferred usleep_range.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>