- 30 8月, 2014 5 次提交
-
-
由 Shahed Shaikh 提交于
This patch adds support to run Power On Self Test (POST) for 83xx adapters. POST can be run in 3 different speed modes : i) Fast mode (takes about 690 ms) ii) Medium mode (takes about 2930 ms) iii) Slow mode (takes about 7500 ms) To run POST, firmware file with name "83xx_post_fw.bin" should be present under /lib/firmware directory. load_fw_file module parameter is used to specify POST operation and its speed mode. load_fw_file = 2 : Fast mode load_fw_file = 3 : Medium mode load_fw_file = 4 : Slow mode Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jitendra Kalsaria 提交于
As per recommendation, msleep() may sleep longer than intended time for values less than 20ms. So, use usleep_range() instead of msleep() Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shahed Shaikh 提交于
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jitendra Kalsaria 提交于
o Update the port type information o Advertise correct link modes and autonegotiation o Add support to change link speed Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Daniel Borkmann 提交于
Replace occurences of skb_get_queue_mapping() and follow-up netdev_get_tx_queue() with an actual helper function. Signed-off-by: NDaniel Borkmann <dborkman@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 8月, 2014 2 次提交
-
-
由 Francois Romieu 提交于
Leftover from 6e1d0b89 ("r8169:add support for RTL8168H and RTL8107E"). Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com> Cc: Chun-Hao Lin <hau@realtek.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next由 David S. Miller 提交于
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2014-08-27 This series contains updates to i40e and i40evf. Carolyn provides two patches, first changes the wording of the flow director add/remove and asynchronous failure messages to include the fd_id to try and add some way to track the operations on a given fd_id. Second adds a check during handle_link_event for unqualified modules when link is down and there is a module plugged in. Anjali provides four patches to i40e/i40evf. First update flow director messages so that a user can tell if a filter was added or deleted. Then updates the ATR policy to not auto-disable ATR when we have errors in programming. The disabling of ATR when we got programming errors was buggy and was still adding new rules and causing continuous errors. With this policy change, we flush instead when we see too many errors. In addition she adds a flow director flush counter to ethtool to help know how many times the interface had to flush and replay the flow director filter table. Updates the driver to ignores a driver perceived transmit hang if the number of descriptors pending is less than 4, and instead log a stat when this situation happens. This is because the queue progresses forward and the stack never experiences a real hang in these situations. Shannon provides three patches for i40e/i40evf, first enables the l2tsel bit on receive queue contexts that are assigned to VFs so that the VF can get the stripped VLAN tag. Then adds a max buffer size parameter to the print helper to be sure the code knows when to stop. Lastly, remove the complaint when removing the default MAC VLAN filter. This was because old firmware had an incorrect MAC VLAN filter that needed to be replaced at startup, and now newer firmware does not have this problem. So now we only add the new filter if the removal succeeded and no need to complain if the removal fails. Ashish provides a change to vsi->num_queue_pairs to equal the number that is configured by the VF. This limits the number of queues that are enabled/disabled and fixes the mismatch case for when a VF configures fewer queues than is allocated to it by the PF. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 28 8月, 2014 33 次提交
-
-
由 David S. Miller 提交于
Mirror the changes made to ixgbe in commit 2367a173 ("ixgbe: flush when in xmit_more mode and under descriptor pressure") Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Mirror the changes made to ixgbe in commit 2367a173 ("ixgbe: flush when in xmit_more mode and under descriptor pressure") Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Daniel Borkmann 提交于
When xmit_more mode is being used and the ring is about to become full or the stack has stopped the ring, enforce a tail pointer write to the hw. Otherwise, we could risk a TX hang. Code suggested by Alexander Duyck. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: NDaniel Borkmann <dborkman@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Florian Fainelli says: ==================== Broadcom BCM7xxx PHY updates for new entries Another week, another set of updates for the Broadcom BCM7xxx PHY driver. This patch set cleanups the existing definitions, adds a macro to ease the addition of future chips, and finally add two new SoCs to the list of supported chips. Resending since the first patch did not make it to the list, sorry about that. Changes in v2: - rephrased commit message for patch 1 to make it pass majordomo capital triple X was rejected ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Add two new entries to the Broadcom BCM7xxx internal PHY driver for BCM7250 and BCM7364 chips. Those chips share the usual 28nm process Gigabit PHY sequence and require the same workarounds so far. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Broadcom started to use a new OUI for its 2013 and newer products: D4-01-29 which translates into 0xae025000 for a 32-bits OUI, add its definition. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
PHY_BCM_OUI_4 is missing two significant digits that actually make it an OUI, add those missing bits so it becomes usable again for matching. Fixes: b560a58c ("net: phy: add Broadcom BCM7xxx internal PHY driver") Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
All 28nm Gigabit PHYs supported by the driver have the same callbacks, the only differences being the 32-bits OUI and the name. Use a macro to factor this, making it easier in the future to add new entries. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Florian Fainelli says: ==================== dsa: Broadcom Starfighter 2 switch support This patch series adds support for the Broadcom Starfighter 2 (Roboswitch successor) using the existing DSA infrastructure. This integrated switch is heavily used in Set Top Box, Cable gateways and DSL gateways products from Broadcom, and to a larger extent the new ARM-based Wi-Fi routers although slightly differently. Changes in v5 are the introduction of ETH_P_XDSA as suggested by Alexander to help capture applications see this is a multiplexed DSA approach now. Changes in v4 are the introducing of an indirection level for DSA switch tag protocols receive and transmit functions. I intentionnaly did not address one comment from Alexander who suggested to move port_names and port_dn in a separate structure since that involves touching arch/arm/ and arch/blackfin/ code which I am not yet comfortable doing. Notable changes in v3 is the preliminary patch that reworks the skb->protocol override helpers for non-Ethertype switch tags, based on feedback from Alexander Duyck. The biggest changes from v1 of this patch series are: - use the new fixed PHY helpers - improved the switch driver with more complete features (interrupts, (RG)MII configuration, memory arrays power down/up, port disabling/enable VLAN separation Future work will focus on bringing the upstream driver in feature parity with the current downstream driver, including: - adding Wake-on-LAN support to the switch - adding suspend/resume callbacks for S2/S3 Power Management modes - extending the switch register interface to cover BCM5310X SoCs ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
The sungem driver has "phy_read()" and "phy_write()" functions, which we need to rename because the generic phy layer is about to export generic interfaces with the same name. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Add the binding documentation for the Broadcom Starfighter 2 integrated switch hardware. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Add documentation for a bunch of new optional properties described in ethernet.txt and fixed-link.txt, this includes: 'phy-handle', 'phy-mode' and the 'fixed-link' subnode. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Add support for the Broadcom Starfigther 2 switch chip using a DSA driver. This switch driver supports the following features: - configuration of the external switch port interface: MII, RevMII, RGMII and RGMII_NO_ID are supported - support for the per-port MIB counters - support for link interrupts for special ports (e.g: MoCA) - powering up/down of switch memories to conserve power when ports are unused Finally, update the compatible property for the DSA core code to match our switch top-level compatible node. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Add support for the 4-bytes Broadcom tag that built-in switches such as the Starfighter 2 might insert when receiving packets, or that we need to insert while targetting specific switch ports. We use a fake local EtherType value for this 4-bytes switch tag: ETH_P_BRCMTAG to make sure we can assign DSA-specific network operations within the DSA drivers. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Allow switch drivers to hook a PHY link update callback to perform port-specific link work. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Whenever libphy determines that the link status of a given PHY/port has changed, allow to call into the switch driver link adjustment callback so proper actions can be taken care of by the switch driver upon link notification. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
In case switch port tagging is disabled (voluntarily, or the switch just does not support it), allow us to continue using the defined set of dsa_device_ops in net/dsa/slave.c. We introduce dsa_protocol_is_tagged() to check whether we need to override skb->protocol and go through the DSA-specifif packet_type function, or if we just go on and receive the SKB through the normal path. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Modify the DSA slave interface to be bound to an arbitray PHY, not just the ones that are available as child PHY devices of the switch MDIO bus. This allows us for instance to have external PHYs connected to a separate MDIO bus, but yet also connected to a given switch port. Under certain configurations, the physical port mask might not be a 1:1 mapping to the MII PHYs mask. This is the case, if e.g: Port 1 of the switch is used and connects to a PHY at a MDIO address different than 1. Introduce a phys_mii_mask variable which allows driver to implement and divert their own MDIO read/writes operations for a subset of the MDIO PHY addresses. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
We will later use the per-port device_node pointer to fetch a bunch of port-specific properties. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
We might need to fetch additional resources from the device tree node pointer, such as register ranges or other properties. Keep a device_node pointer around for this. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
In preparation for updating the DSA code and avoid using ifdefs there, provide an empty stub for fixed_phy_set_link_update when CONFIG_FIXED_PHY is not selected. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Add a generic UniMAC MDIO bus driver and its Device Tree binding, which can be used by the BCMGENET driver as-is, and the upcoming Starfighter 2 Ethernet switch MDIO bus controller. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
DSA is currently registering one packet_type function per EtherType it needs to intercept in the receive path of a DSA-enabled Ethernet device. Right now we have three of them: trailer, DSA and eDSA, and there might be more in the future, this will not scale to the addition of new protocols. This patch proceeds with adding a new layer of abstraction and two new functions: dsa_switch_rcv() which will dispatch into the tag-protocol specific receive function implemented by net/dsa/tag_*.c dsa_slave_xmit() which will dispatch into the tag-protocol specific transmit function implemented by net/dsa/tag_*.c When we do create the per-port slave network devices, we iterate over the switch protocol to assign the DSA-specific receive and transmit operations. A new fake ethertype value is used: ETH_P_XDSA to illustrate the fact that this is no longer going to look like ETH_P_DSA or ETH_P_TRAILER like it used to be. This allows us to greatly simplify the check in eth_type_trans() and always override the skb->protocol with ETH_P_XDSA for Ethernet switches tagged protocol, while also reducing the number repetitive slave netdevice_ops assignments. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
The sungem driver has "phy_read()" and "phy_write()" functions, which we need to rename because the generic phy layer is about to export generic interfaces with the same name. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
The dmfe driver has "phy_read()" and "phy_write()" functions, which we need to rename because the generic phy layer is about to export generic interfaces with the same name. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Unfortunately, the USB gadget layer has this weird things where NULL skbs are passed into ops->ndo_start_xmit() in order to trigger the dev->wrap() calls to build packets. This is completely outside of the allowable range of sane arguments for the ndo_start_xmit method. All invocations of ndo_start_xmit() should be with non-NULL SKB arguments. Put back the direct call, but with a comment explaining how this is not acceptable in the long term. Reported-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Romain Perier 提交于
Some platforms have special bank registers which might be used to select the correct clock or the right mode for Media Indepent Interface controllers. Sometimes, it is also required to activate vcc regulators in the right order to supply the ethernet controller at the right time. This patch is an architecture refactoring of the arc-emac device driver. It adds a new software design which allows to add specific platform glue layer. Each platform has now its own module which performs custom initialization and remove for the target and then calls to the core driver. Signed-off-by: NRomain Perier <romain.perier@gmail.com> Reviewed-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Romain Perier 提交于
This is an api changes for the emac_mdio.c module. It will be required later when arc_emac_probe/arc_emac_remove will no longer use 'struct platform_device'. Signed-off-by: NRomain Perier <romain.perier@gmail.com> Reviewed-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Romain Perier 提交于
This is a preparation of an api changes for the emac_main.c module. The involved functions are arc_emac_probe and arc_emac_remove. Signed-off-by: NRomain Perier <romain.perier@gmail.com> Reviewed-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Westphal 提交于
only written once. Signed-off-by: NFlorian Westphal <fw@strlen.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Incorrect checking of array instead of array contents in panic_dump flow - results of commit e2611998 ("bnx2x: Safe bnx2x_panic_dump()"). Reported-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 hayeswang 提交于
Replace the strncpy with strlcpy, and use sizeof to determine the length. Signed-off-by: NHayes Wang <hayeswang@realtek.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
We lost one when xmit_more was added. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-