Call ixgbe_copy_dcb_cfg() earlier in the ixgbe_dcbnl_set_all() so that
we can learn if this is going to fail as early as possible.  Previously,
ixgbe_down or ixgbe_close were being called before this check and the
IXGBE_RESETTING bit was being set and cleared.  Worse if this failed
the corresponding ixgbe_up/ndo_open would not called.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NPJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the correct bit BIT_PG_TX when tx PG settings are set.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NPJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change fixes an issue in igbvf with mapped_as_page being left set
after a page is unmapped which results in buffers which are mapped via map
single being unmapped as page.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hello David Miller,

I fix a bug in ks8851_mll driver, which has existed since 2.6.32-rc6.

>From : David J. Choi <david.choi@micrel.com>

Fix a bug that the data pointers in the interrupt handler are set wrong, which is related with the 5th parameter of request_irq().

Signed-off-by : David J. Choi <david.choi@micrel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bug fix in be2net for newer generation of BladeEngine ASIC.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netdev_open() will return without cleaning up net device or hardware state
if firmware loading fails.  This results in a BUG() on a second attempt to
bring the interface up, reported in
<http://bugzilla.kernel.org/show_bug.cgi?id=15091>, and probably has even
worse effects if the driver is removed afterwards.

Call netdev_close() to clean up on failure.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=15091Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Reported-by: NMichael Moffatt <michael@moffatt.org.nz>
Tested-by: NMichael Moffatt <michael@moffatt.org.nz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I got below kernel oops when I try to bring down the network interface if
ftrace is enabled. The root cause is drv_ampdu_action() is passed with a
NULL ssn pointer in the BA session tear down case. We need to check and
avoid dereferencing it in trace entry assignment.

BUG: unable to handle kernel NULL pointer dereference
Modules linked in: at (null)
IP: [<f98fe02a>] ftrace_raw_event_drv_ampdu_action+0x10a/0x160 [mac80211]
*pde = 00000000
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
[...]
Call Trace:
 [<f98fdf20>] ? ftrace_raw_event_drv_ampdu_action+0x0/0x160 [mac80211]
 [<f98dac4c>] ? __ieee80211_stop_rx_ba_session+0xfc/0x220 [mac80211]
 [<f98d97fb>] ? ieee80211_sta_tear_down_BA_sessions+0x3b/0x50 [mac80211]
 [<f98dc6f6>] ? ieee80211_set_disassoc+0xe6/0x230 [mac80211]
 [<f98dc6ac>] ? ieee80211_set_disassoc+0x9c/0x230 [mac80211]
 [<f98dcbb8>] ? ieee80211_mgd_deauth+0x158/0x170 [mac80211]
 [<f98e4bdb>] ? ieee80211_deauth+0x1b/0x20 [mac80211]
 [<f8987f49>] ? __cfg80211_mlme_deauth+0xe9/0x120 [cfg80211]
 [<f898b870>] ? __cfg80211_disconnect+0x170/0x1d0 [cfg80211]

Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit 0b5ccb2e(title:ipv6: reassembly: use seperate reassembly queues for
conntrack and local delivery) has broken the saddr&&daddr member of
nf_ct_frag6_queue when creating new queue.  And then hash value
generated by nf_hashfn() was not equal with that generated by fq_find().
So, a new received fragment can't be inserted to right queue.

The patch fixes the bug with adding member of user to nf_ct_frag6_queue structure.
Signed-off-by: NShan Wei <shanwei@cn.fujitsu.com>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I have seen RX stalls on a machine that experienced a suspected
OOM.  After the stall, the RX buffer is empty on the guest side
and there are exactly 16 entries available on the host side.  As
the number of entries is less than that required by a maximal
skb, the host cannot proceed.

The guest did not have a refill job scheduled.

My diagnosis is that an OOM had occured, with the delayed refill
job scheduled.  The job was able to allocate at least one skb, but
not enough to overcome the minimum required by the host to proceed.

As the refill job would only reschedule itself if it failed completely
to allocate any skbs, this would lead to an RX stall.

The following patch removes this stall possibility by always
rescheduling the refill job until the ring is totally refilled.

Testing has shown that the RX stall no longer occurs whereas
previously it would occur within a day.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The low-level MCDI code always uses 32-bit MMIO operations, and
callers must pad input and output buffers to multiples of 4 bytes.
The MCDI NVRAM functions are not doing this.  Also, their buffers are
declared as variable-length arrays with no explicit maximum length.

Switch to a fixed buffer size based on the chunk size used by the
MTD driver (which is a multiple of 4).
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to a hardware bug in the SFC9000 family, the firmware must
transfer raw GMAC statistics to host memory before aggregating them
into the cooked (speed-independent) MAC statistics.  Extend the stats
buffer to support this.

The length of the buffer is explicit in the MAC_STATS command, so this
change is backward-compatible on both sides.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By rounding up the buffer size to power of 2, several expensive
modulus operations can be avoided.  This patch also solves a bug where
the gap need when ring gets full was not being accounted for.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently qlge tries to release regions even if they were not allocated.
This causes messages like the following in the kernel log

Trying to free nonexistent resource <00000000006af400-00000000006af4ff>
Trying to free nonexistent resource <00003c04ff9f4000-00003c04ff9f7fff>
Trying to free nonexistent resource <00003c04ffc00000-00003c04ffcfffff>

This patch fixes the goto logic in order to not release the resources
if they were not allocated.
Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Among other changes, this commit:

   commit 06d0f066
   Author: Sujith <Sujith.Manoharan@atheros.com>
   Date:   Thu Feb 12 10:06:45 2009 +0530

   ath9k: Enable Fractional N mode

changed the hw attach code to fix up initialization values only for
dual band devices, however the commit message did not give a reason as
to why this would be useful or necessary.

According to tests by Jorge Boncompte, this breaks at least some
2GHz-only cards, so the code should be changed back to the
unconditional INI fixup.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Reported-by: NJorge Boncompte <jorge@dti2.net>
Cc: stable@kernel.org
Tested-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are a few station addresses that are
char *, instead of the normal u8 *; gcc
gives pointer signedness warnings for some
of those, so use u8 * consistently.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

GC is non-existent in netns, so after you hit GC threshold, no new
dst entries will be created until someone triggers cleanup in init_net.

Make xfrm4_dst_ops and xfrm6_dst_ops per-netns.
This is not done in a generic way, because it woule waste
(AF_MAX - 2) * sizeof(struct dst_ops) bytes per-netns.

Reorder GC threshold initialization so it'd be done before registering
XFRM policies.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Obviously, this register had some other impact that is causing
the regression.  Either it is masking some other access or needs
to be reset in some path.

Either, way it is best to just revert the change for 2.6.33

This reverts commit 166a0fd4.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bruno Prémont found commit 9793241f
(vlan: Precise RX stats accounting) added a regression for non
hw accelerated vlans.

[   26.390576] BUG: unable to handle kernel NULL pointer dereference at (null)
[   26.396369] IP: [<df856b89>] vlan_skb_recv+0x89/0x280 [8021q]

vlan_dev_info() was used with original device, instead of
skb->dev. Also spotted by Américo Wang.
Reported-By: NBruno Prémont <bonbons@linux-vserver.org>
Tested-By: NBruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"ip xfrm state|policy count" report SA/SP count from init_net,
not from netns of caller process.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Y2_HW_WOL_ON/Y2_HW_WOL_OFF should be set and cleared per chip,
not per port.  On dual port cards, Y2_HW_WOL_ON should be
enabled if either sky2 port has WOL enabled.

Found while reviewing code for a WOL regression, though this is
probably not the cause of the regression.
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Found this problem when testing IPv6 from a KVM guest to a remote
host via e1000e device on the host.
The following patch fixes the check for IPv6 GSO packet in Intel
ethernet drivers to use skb_is_gso_v6(). SKB_GSO_DODGY is also set
when packets are forwarded from a guest.
Signed-off-by: NSridhar Samudrala <sri@us.ibm.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After removing the skb_dma_map/unmap calls the exception handling in
igb_tx_map_adv is not correct.  The issue is that the count value was not
being correctly handled so as a result we were not rewinding the ring as
back as we should have been.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add igbvf to the list of supported Intel drivers and Alex to the list of
maintainers.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When testing the "e1000: enhance frame fragment detection" (and e1000e)
patches we found some bugs with reducing the MTU size.  The 1024 byte
descriptor used with the 1000 mtu test also (re) introduced the
(originally) reported bug, and causes us to need the e1000_clean_tx_irq
"enhance frame fragment detection" fix.

So what has occured here is that 2.6.32 is only vulnerable for mtu <
1500 due to the jumbo specific routines in both e1000 and e1000e.
So, 2.6.32 needs the 2kB buffer len fix for those smaller MTUs, but
is not vulnerable to the original issue reported.  It has been pointed
out that this vulnerability needs to be patched in older kernels that
don't have the e1000 jumbo routine.  Without the jumbo routines, we
need the "enhance frame fragment detection" fix the e1000, old
e1000e is only vulnerable for < 1500 mtu, and needs a similar
fix.  We split the patches up to provide easy backport paths.

There is only a slight bit of extra code when this fix and the
original "enhance frame fragment detection" fixes are applied, so
please apply both, even though it is a bit of overkill.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fmvj18x_cs, serial_cs:
 add new id
 Panasonic lan & modem card (model name:AL-VML101)
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only the first two fields of mcc wrb - embedded, payload_len
need to be cpu_to_le32() swapped while issuing a cmd to the hw.
The fields tag0, tag1 are opaque and returned back to cpu as is...
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Please add support for Microsoft MN-120 PCMCIA network card. It's an
old card, I know, but adding support is very easy. You just need to
get tulip_core.c to recognise its vendor/device ID.

Patch for kernel 2.6.32.4 (and many previous) attached.

 .....Ron Murray
Signed-off-by: NRon Murray <rjmx@rjmx.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pages are posted to the rxq in such a way that more than one frag
can share the page. The last frag that uses the page unmaps the
page.  In the case when a page is not fully used (due to lack of space in rxq)
the last frag that uses the page is not being set as a "last_page_user";
instead, the next frag in the rxq is incorrectly being set.

The fix has also been tested on ppc64 with 64k pages...
Signed-off-by: NSathya Perla <sathyap@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Intel WiMax Wireless Link 6050 can show under more than one USB
ID. Add support for all, introducing a generic flag (i2400mu->i6050)
that denotes a 6x50 based device.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf: x86: Add support for the ANY bit
  perf: Change the is_software_event() definition
  perf: Honour event state for aux stream data
  perf: Fix perf_event_do_pending() fallback callsite
  perf kmem: Print usage help for unknown commands
  perf kmem: Increase "Hit" column length
  hw-breakpoints, perf: Fix broken mmiotrace due to dr6 by reference change
  perf timechart: Use tid not pid for COMM change

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: Reassign prev and switch_count when reacquire_kernel_lock() fail
  sched: Fix vmark regression on big machines

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: retry FS IOs even if it has failed with AC_ERR_INVALID

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  tty: fix race in tty_fasync
  serial: serial_cs: oxsemi quirk breaks resume
  serial: imx: bit &/| confusion
  serial: Fix crash if the minimum rate of the device is > 9600 baud
  serial-core: resume serial hardware with no_console_suspend
  serial: 8250_pnp: use wildcard for serial Wacom tablets
  nozomi: quick fix for the close/close bug
  compat_ioctl: Supress "unknown cmd" message on serial /dev/console

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  Staging: hv: fix smp problems in the hyperv core code
  Staging: et131x: Fix 2.6.33rc1 regression in et131x
  Staging: asus_oled: fix oops in 2.6.32.2

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  Revert "sysdev: fix prototype for memory_sysdev_class show/store functions"
  driver-core: fix devtmpfs crash on s390

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: isp1362: fix build failure on ARM systems via irq_flags cleanup
  USB: isp1362: better 64bit printf warning fixes
  USB: fix usbstorage for 2770:915d delivers no FAT
  USB: Fix level of isp1760 Reloading ptd error message
  USB: FHCI: avoid NULL pointer dereference
  USB: Fix duplicate sysfs problem after device reset.
  USB: add speed values for USB 3.0 and wireless controllers
  USB: add missing delay during remote wakeup
  USB: EHCI & UHCI: fix race between root-hub suspend and port resume
  USB: EHCI: fix handling of unusual interrupt intervals
  USB: Don't use GFP_KERNEL while we cannot reset a storage device
  USB: fix bitmask merge error
  usb: serial: fix memory leak in generic driver
  USB: serial: fix USB serial fix kfifo_len locking