On 64 bit systems the agp_info struct has a 4 byte hole between
->agp_mode and ->aper_base.  We need to clear it to avoid disclosing
stack information to userspace.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

PCF8523 uses 1-12 to represent month according to datasheet.
link: www.nxp.com/documents/data_sheet/PCF8523.pdf.
Signed-off-by: NChris Cui <chris.wei.cui@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Under "heavy" RX load, the driver cannot handle the descriptors fast
enough. In detail, when a descriptor is consumed, its used flag is
cleared and once the RX budget is consumed all descriptors with a
cleared used flag are prepared to receive more data. Under load though,
the HW may constantly receive more data and use those descriptors with a
cleared used flag before they are actually prepared for next usage.

The head and tail pointers into the RX-ring should always be valid and
we can omit clearing and checking of the used flag.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Coverage data suggests that the unlikely case of receiving data while
the receive handler is running may not be that unlikely.
Coverage data after running iperf for a while:
    91320:  891:	work_done = bp->macbgem_ops.mog_rx(bp, budget);
    91320:  892:	if (work_done < budget) {
     2362:  893:		napi_complete(napi);
        -:  894:
        -:  895:		/* Packets received while interrupts were disabled */
     4724:  896:		status = macb_readl(bp, RSR);
     2362:  897:		if (unlikely(status)) {
      762:  898:			if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
      762:  899:				macb_writel(bp, ISR, MACB_BIT(RCOMP));
        -:  900:			napi_reschedule(napi);
        -:  901:		} else {
     1600:  902:			macb_writel(bp, IER, MACB_RX_INT_FLAGS);
        -:  903:		}
        -:  904:	}
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When data is received during the driver processing received data the
NAPI is re-scheduled. In that case the RX interrupt should not be
re-enabled.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A few interrupt flags were not cleared in the ISR, resulting in a sytem
trapped in the ISR in cases one of those interrupts occurred. Clear all
flags to avoid such situations.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Just as commit "net: macb: DMA-unmap full rx-buffer"
(48330e08), pass the size that
was used for mapping the memory also to the unmap routine to
avoid warnings from the DMA_API.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It has been determined that the workaround of putting the PHY into MDIO
slow mode to access the PHY id is not necessary with Lynx Point and newer
parts.  The issue that necessitated the workaround has been fixed on the
newer hardware.

We will maintains, as a last ditch attempt, the conversion to MDIO Slow
Mode in the failure branch when attempting to access the PHY id so as to
cover all contingencies.
Signed-off-by: NDave Ertman <davidx.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Several customers have reported a link flap issue on 82579. The symptoms
are random and intermittent link losses when 82579 is connected to specific
link partners. Issue has been root caused as interoperability problem
between 82579 and at least some Broadcom PHYs in the Energy Efficient
Ethernet wake mechanism.

To fix the issue, we are disabling the Phase Locked Loop shutdown in 100M
Low Power Idle.  This solution will cause an increase of power in 100M EEE
link. It will cost additional 28mW in this specific mode.

Cc: Lukasz Adamczuk <lukasz.adamczuk@intel.com>
Signed-off-by: NDave Ertman <davidx.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In commit 772d05c5 "e1000e: slow performance
between two 82579 connected via 10Mbit hub", a workaround was put into place
to address the overaggressive transmit behavior of 82579 parts when connecting
at 10Mbs half-duplex.

This same behavior is seen on i217 and i218 parts as well.  This patch expands
the original workaround to encompass these parts.
Signed-off-by: NDave Ertman <davidx.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is a workaround for a HW erratum on 82579 devices.
Erratum is #23 in Intel 6 Series Chipset and Intel C200 Series Chipset
specification Update June 2013.

Problem: 82579 parts experience packet loss in Gig and 100 speeds
when interconnect between PHY and MAC is exiting K1 power saving state.
This was previously believed to only affect 1Gig speed, but has been observed
at 100Mbs also.

Workaround: Disable K1 for 82579 devices at Gig and 100 speeds.
Signed-off-by: NDave Ertman <davidx.m.ertman@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Carrying out PCI speed/width checks through pcie_get_minimum_link()
on VFs yield wrong results, so remove them.

Fixes: b912b2f8 ('net/mlx4_core: Warn if device doesn't have enough PCI bandwidth')
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When running in SRIOV mode, VM that is assigned with a non-provisioned
Ethernet VFs get themselves a random mac when the Eth driver starts. In
this case, if the IB driver startup code that deals with RoCE runs first,
it will use a zero mac as the source mac for the Para-Virtual CM MADs
which is buggy. To handle that, we change the order of loading.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code that deals with computing the slave id based on a given GID
gave wrong results when the number of single port VFs wasn't the
same for port 1 vs. port 2 and the relevant VF is single ported on
port 2. As a result, incoming CM MADs were dispatched to the wrong VF.
Fixed that and added documentation to clarify the computation steps.

Fixes: 449fc488 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using single ported VFs and the VF is using port 2, we need
to adjust the port accordingly (change it from 1 to 2).

Fixes: 449fc488 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NJack Morgenstein <jackm@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 4d619f62 ("net: cdc_ncm: no point in filling up the NTBs
if we send ZLPs") changed the padding logic for devices with the ZLP
flag set.  This meant that frames of any size will be sent without
additional padding, except for the single byte added if the size is
a multiple of the USB packet size. But if the unpadded size is
identical to the maximum frame size, and the maximum size is a
multiplum of the USB packet size, then this one-byte padding will
overflow the buffer.

Prevent padding if already at maximum frame size, letting usbnet
transmit a ZLP instead in this case.

Fixes: 4d619f62 ("net: cdc_ncm: no point in filling up the NTBs if we send ZLPs")
Reported by: Yu-an Shih <yshih@nvidia.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If NO_DMA=y:

drivers/built-in.o: In function `altera_tse_probe':
altera_tse_main.c:(.text+0x25ec2e): undefined reference to `dma_set_mask'
altera_tse_main.c:(.text+0x25ec78): undefined reference to `dma_supported'
altera_tse_main.c:(.text+0x25ecb6): undefined reference to `dma_supported'
drivers/built-in.o: In function `sgdma_async_read':
altera_sgdma.c:(.text+0x25f620): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f678): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f696): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f6f0): undefined reference to `dma_map_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f702): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `sgdma_tx_buffer':
(.text+0x25f92a): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_rx_status':
(.text+0x25fa24): undefined reference to `dma_sync_single_for_cpu'
make[3]: *** [vmlinux] Error 1
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NVince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not leak kernel-only floppy_raw_cmd structure members to userspace.
This includes the linked-list pointer and the pointer to the allocated
DMA space.
Signed-off-by: NMatthew Daley <mattd@bugfuzz.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Always clear out these floppy_raw_cmd struct members after copying the
entire structure from userspace so that the in-kernel version is always
valid and never left in an interdeterminate state.
Signed-off-by: NMatthew Daley <mattd@bugfuzz.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When building the name for the workqueue thread, make sure a format
string cannot leak in from the disk name.
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

The ubi->free_count should be updated with every insert/remove to/from
the ubi->free list.
Signed-off-by: NTanya Brokhman <tlinder@codeaurora.org>
Reviewed-by: NDolev Raviv <draviv@codeaurora.org>
Acked-by: NRichard Weinberger <richard@nod.at>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

In case of an error (if there are not free PEB's for example),
__wl_get_peb will return a negative value. In order to prevent access
violation we need to test the returned value prior to using it later on.
Signed-off-by: NTatyana Brokhman <tlinder@codeaurora.org>
Reviewed-by: NDolev Raviv <draviv@codeaurora.org>
Acked-by: NRichard Weinberger <richard@nod.at>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

Following arm64 commit bc3ee18a (arm64: init: Move of_clk_init to
time_init()), vexpress_osc_of_setup() is called via of_clk_init() long
before initcalls are issued. Initialising the vexpress oscillators
requires the vespress sysregs to be already initialised, so this patch
adds an explicit call to vexpress_sysreg_of_early_init() in vexpress
oscillator setup function.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Tested-by: NWill Deacon <will.deacon@arm.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Tested-by: NPawel Moll <pawel.moll@arm.com>
Acked-by: NPawel Moll <pawel.moll@arm.com>
Cc: Mike Turquette <mturquette@linaro.org>

Signed-off-by: NDaniele Forsi <dforsi@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NVictor A. Santos <victoraur.santos@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 6a20dbd6,
"tty: Fix race condition between __tty_buffer_request_room and flush_to_ldisc"
correctly identifies an unsafe race condition between
__tty_buffer_request_room() and flush_to_ldisc(), where the consumer
flush_to_ldisc() prematurely advances the head before consuming the
last of the data committed. For example:

           CPU 0                     |            CPU 1
__tty_buffer_request_room            | flush_to_ldisc
  ...                                |   ...
                                     |   count = head->commit - head->read
  n = tty_buffer_alloc()             |
  b->commit = b->used                |
  b->next = n                        |
                                     |   if (!count)                /* T */
                                     |     if (head->next == NULL)  /* F */
                                     |     buf->head = head->next

In this case, buf->head has been advanced but head->commit may have
been updated with a new value.

Instead of reintroducing an unnecessary lock, fix the race locklessly.
Read the commit-next pair in the reverse order of writing, which guarantees
the commit value read is the latest value written if the head is
advancing.
Reported-by: NManfred Schlaegl <manfred.schlaegl@gmx.at>
Cc: <stable@vger.kernel.org> # 3.12.x+
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 6a20dbd6.

Although the commit correctly identifies an unsafe race condition
between __tty_buffer_request_room() and flush_to_ldisc(), the commit
fixes the race with an unnecessary spinlock in a lockless algorithm.

The follow-on commit, "tty: Fix lockless tty buffer race" fixes
the race locklessly.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When 'console=hvc0' is specified to the kernel parameter in x86 KVM guest,
hvc console is setup within a kthread. However, that will cause SEGV
and the boot will fail when the driver is builtin to the kernel,
because currently hvc_console_setup() is annotated with '__init'. This
patch removes '__init' to boot the guest successfully with 'console=hvc0'.
Signed-off-by: NTomoki Sekiyama <tomoki.sekiyama@hds.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The tty atomic_write_lock does not provide an exclusion guarantee for
the tty driver if the termios settings are LECHO & !OPOST.  And since
it is unexpected and not allowed to call TTY buffer helpers like
tty_insert_flip_string concurrently, this may lead to crashes when
concurrect writers call pty_write. In that case the following two
writers:
* the ECHOing from a workqueue and
* pty_write from the process
race and can overflow the corresponding TTY buffer like follows.

If we look into tty_insert_flip_string_fixed_flag, there is:
  int space = __tty_buffer_request_room(port, goal, flags);
  struct tty_buffer *tb = port->buf.tail;
  ...
  memcpy(char_buf_ptr(tb, tb->used), chars, space);
  ...
  tb->used += space;

so the race of the two can result in something like this:
              A                                B
__tty_buffer_request_room
                                  __tty_buffer_request_room
memcpy(buf(tb->used), ...)
tb->used += space;
                                  memcpy(buf(tb->used), ...) ->BOOM

B's memcpy is past the tty_buffer due to the previous A's tb->used
increment.

Since the N_TTY line discipline input processing can output
concurrently with a tty write, obtain the N_TTY ldisc output_lock to
serialize echo output with normal tty writes.  This ensures the tty
buffer helper tty_insert_flip_string is not called concurrently and
everything is fine.

Note that this is nicely reproducible by an ordinary user using
forkpty and some setup around that (raw termios + ECHO). And it is
present in kernels at least after commit
d945cb9c (pty: Rework the pty layer to
use the normal buffering logic) in 2.6.31-rc3.

js: add more info to the commit log
js: switch to bool
js: lock unconditionally
js: lock only the tty->ops->write call

References: CVE-2014-0196
Reported-and-tested-by: NJiri Slaby <jslaby@suse.cz>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NJiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The sleep function was updated to put the serial port to sleep only when necessary.
This appears to resolve the errant behavior of the driver as described in
Kernel Bug 61961 – "My Exar Corp. XR17C/D152 Dual PCI UART modem does not
work with 3.8.0".
Signed-off-by: NMichael Welling <mwelling@ieee.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Per reference manuals of Freescale P1020 and P2020 SoCs, USB controller
present in these SoCs has bit 17 of USBx_CONTROL register marked as
Reserved - there is no PHY_CLK_VALID bit there.

Testing for this bit in ehci_fsl_setup_phy() behaves differently on two
P1020RDB boards available here - on one board test passes and fsl-usb
init succeeds, but on other board test fails, causing fsl-usb init to
fail.

This patch changes ehci_fsl_setup_phy() not to test PHY_CLK_VALID on
controller version 1.6 that (per manual) does not have this bit.
Signed-off-by: NNikita Yushchenko <nyushchenko@dev.rtsoft.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Even if the USB-to-ATAPI converter supported multiple LUNs, this
driver would always detect the same physical device or media because
it doesn't use srb->device->lun in any way.
Tested with an Hewlett-Packard CD-Writer Plus 8200e.
Signed-off-by: NDaniele Forsi <dforsi@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Dan writes:

"The Dell drivers use the same configuration for PIDs:

81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card
81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card
81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card
81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card
81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card

These devices are all clearly Sierra devices, but are also definitely
Gobi-based.  The A8 might be the MC7700/7710 and A9 is likely a MC7750.

>From DellGobi5kSetup.exe from the Dell drivers:

usbif0: serial/firmware loader?
usbif2: nmea
usbif3: modem/ppp
usbif8: net/QMI"

Cc: <stable@vger.kernel.org>
Reported-by: NAceLan Kao <acelan.kao@canonical.com>
Reported-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some OHCI controllers from ATI/AMD seem to have difficulty with
"global" USB suspend, that is, suspending an entire USB bus without
setting the suspend feature for each port connected to a device.  When
we try to resume the child devices, the controller gives timeout
errors on the unsuspended ports, requiring resets, and can even cause
ohci-hcd to hang; see

	http://marc.info/?l=linux-usb&m=139514332820398&w=2

and the following messages.

This patch fixes the problem by adding a new quirk flag to ohci-hcd.
The flag causes the ohci_rh_suspend() routine to suspend each
unsuspended, enabled port before suspending the root hub.  This
effectively converts the "global" suspend to an ordinary root-hub
suspend.  There is no need to unsuspend these ports when the root hub
is resumed, because the child devices will be resumed anyway in the
course of a normal system resume ("global" suspend is never used for
runtime PM).

This patch should be applied to all stable kernels which include
commit 0aa2832d (USB: use "global suspend" for system sleep on
USB-2 buses) or a backported version thereof.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NPeter Münster <pmlists@free.fr>
Tested-by: NPeter Münster <pmlists@free.fr>
CC: <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The following commit:

commit 9ec36caf
Author: Rob Herring <robh@kernel.org>
Date:   Wed Apr 23 17:57:41 2014 -0500

    of/irq: do irq resolution in platform_get_irq

changed platform_get_irq() which now returns EINVAL and EPROBE_DEFER,
in addition to ENXIO. If there's no interrupt for mvmdio, platform_get_irq()
returns EINVAL, but we currently check only for ENXIO.

Fix this by looking for a positive integer, which is the proper way of
validating a virtual interrupt number.

While at it, add a proper handling for the deferral probe case.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phy_state_machine should check whether auto-negotiatin is completed
before changing phydev->state from PHY_NOLINK to PHY_RUNNING. If
auto-negotiation is not completed phydev->state should be set to
PHY_AN.
Signed-off-by: NBalakumaran Kannan <kumaran.4353@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 2ee57d58 ("dm cache: add passthrough mode") inadvertently
removed the deferred set reference that was taken in cache_map()'s
writethrough mode support.  Restore taking this reference.

This issue was found with code inspection.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Acked-by: NJoe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org # 3.13+

This reverts commit 9fb6c9c7.

Tjmax on some Intel CPUs is below 85 degrees C. One known example is
L5630 with Tjmax of 71 degrees C. There are other Xeon processors with
Tjmax of 70 or 80 degrees C. Also, the Intel IA32 System Programming
document states that the temperature target is in bits 23:16 of MSR 0x1a2
(MSR_TEMPERATURE_TARGET), which is 8 bits, not 7.

So even if turbostat uses similar checks to validate Tjmax, there is no
evidence that the checks are actually required. On the contrary, the
checks are known to cause problems and therefore need to be removed.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=75071.

Fixes: 9fb6c9c7 hwmon: (coretemp) Refine TjMax detection
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

According commit d640113f (ACPI: processor: fix acpi_get_cpuid for UP
processor),  BIOS may not provide _MAT or MADT tables and acpi_get_apicid()
always returns -1. For these cases, original code will pass apic_id with
vaule of -1 to acpi_map_cpuid() and it will check the acpi_id. If acpi_id
is equal to zero, ignores apic_id and return zero for CPU0.

Commit b981513f (ACPI / scan: bail out early if failed to parse APIC
ID for CPU) changed the behavior. Return ENODEV when find apic_id is
less than zero after calling acpi_get_apicid(). This causes acpi-cpufreq
driver fails to be loaded on some machines. This patch is to fix it.

Fixes: b981513f (ACPI / scan: bail out early if failed to parse APIC ID for CPU)
References: https://bugzilla.kernel.org/show_bug.cgi?id=73781
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Reported-and-tested-by: NKATO Hiroshi <katoh@mikage.ne.jp>
Reported-and-tested-by: NStuart Foster <smf.linux@ntlworld.com>
Signed-off-by: NLan Tianyu <tianyu.lan@intel.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The ACPI PNP subsystem returns errors from pnpacpi_set_resources()
and pnpacpi_disable_resources() if the _SRS or _DIS methods are not
present, respectively, but it should not do that, because those
methods are optional.  For this reason, modify pnpacpi_set_resources()
and pnpacpi_disable_resources(), respectively, to ignore missing _SRS
or _DIS.

This problem has been uncovered by commit 202317a5 (ACPI / scan:
Add acpi_device objects for all device nodes in the namespace) and
manifested itself by causing serial port suspend to fail on some
systems.

Fixes: 202317a5 (ACPI / scan: Add acpi_device objects for all device nodes in the namespace)
References: https://bugzilla.kernel.org/show_bug.cgi?id=74371Reported-by: Nwxg4net <wxg4net@gmail.com>
Reported-and-tested-by: <nonproffessional@gmail.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>