Move the array declaration to hda_codec.c where it is used and add includes
where the individual presets are declared.

Fixes the following sparse warnings:
sound/pci/hda/patch_realtek.c:13744:25: warning: symbol 'snd_hda_preset_realtek' was not declared. Should it be static?
sound/pci/hda/patch_cmedia.c:729:25: warning: symbol 'snd_hda_preset_cmedia' was not declared. Should it be static?
sound/pci/hda/patch_analog.c:3656:25: warning: symbol 'snd_hda_preset_analog' was not declared. Should it be static?
sound/pci/hda/patch_sigmatel.c:3995:25: warning: symbol 'snd_hda_preset_sigmatel' was not declared. Should it be static?
sound/pci/hda/patch_si3054.c:286:25: warning: symbol 'snd_hda_preset_si3054' was not declared. Should it be static?
sound/pci/hda/patch_atihdmi.c:156:25: warning: symbol 'snd_hda_preset_atihdmi' was not declared. Should it be static?
sound/pci/hda/patch_conexant.c:1721:25: warning: symbol 'snd_hda_preset_conexant' was not declared. Should it be static?
sound/pci/hda/patch_via.c:1962:25: warning: symbol 'snd_hda_preset_via' was not declared. Should it be static?
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The HD-audio parameters are at most 32bit int.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Temp variable in the loop shadows the second argument (which is otherwise
unused in this function).  Change this to defcfg as it is used to hold
the default config.
sound/pci/hda/patch_sigmatel.c:2759:18: warning: symbol 'cfg' shadows an earlier one
sound/pci/hda/patch_sigmatel.c:2734:26: originally declared here
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix the initial num_dacs of 92HD71bxx codecs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added logic to check if AUTO_PIN_FRONT_MIC is available for output
switch, if AUTO_PIN_MIC isn't.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some laptops have a internal analog microphone that is not setup by the BIOS.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added PCI_QUIRKS for laptop that have the 92HDxxx family of codecs.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

STAC_DELL_BIOS quirks were setting the association value wrong
for port 0x0f, which prevented it from being included in hp_outs[].
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix issue on STAC927x codecs that first DAC was getting powered down
even if was being used.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use a private array for TLV entries of virtual master controls instead
of (supposed) static array.  This cleans up the existing codes.

Also, now vmaster assumes the simple dB-range TLV that is the only type
it can handle.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added a new mixer switch to enable/disable the sharing of the default
PCM stream with analog and SPDIF outputs.  When "IEC958 Default PCM"
switch is on, the PCM stream is routed both to analog and SPDIF outputs.
This is the behavior in the earlier version.

Turning this switch off has a merit for some codecs, though.  Some codec
chips don't support 24bit formats for SPDIF but only for analog outputs.
In this case, you can use 24bit format by disabling this switch.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

On several laptops that have STAC9228 codecs have unused DACs,
this powers them down to a D3 state.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In the current scheme, PCM device numbers are assigned incrementally
in the order of codecs.  This causes problems when the codec number
is irregular, e.g. codec #0 for HDMI and codec #1 for analog.  Then
the HDMI becomes the first PCM, which is picked up as the default
output device.  Unfortuantely this doesn't work well with normal
setups.

This patch introduced the fixed device numbers for the PCM types,
namely, analog, SPDIF, HDMI and modem.  The PCM devices are assigned
according to the corresponding PCM type.  After this patch, HDMI will
be always assigned to PCM #3, SPDIF to PCM #1, and the first analog
to PCM #0, etc.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds support for the OQO Model 2 Ultra Mobile PC.
Signed-off-by: NTobin Davis <tdavis@dsl-only.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Some laptop has an internal analog microphone that is 'fixed'.
This patch prevents creating a 'Mic In as Output' switch for
ports that can't be outputs.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Support added for detecting HP jack presence via GPIO on several laptop docks.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add SPDIF playback switch to the slave element list so that it
can be toggled via the master control as well.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

This patch checks to see the Line In/Mic port have the ability
to do output before creating the the control switches.
The 92hd71bxx series of codecs has this issue with the port 0xe,
which only allows input.
Signed-off-by: NMatthew Ranostay <mranostay@embededalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Fixed issue that the incorrect GPIO line was being pulled high
for some STAC9205 based laptops.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Allows for dynamically creating mono out mixer controls and well
as mono mux controls.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add support for the mono mux on several 92HD7xxx codecs.
Creates a dynamic mixer for the mux selection.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Some machines with STAC codecs seem to have problems (e.g. no audible
playback) when the delay in codec-read routine is too short.
I still don't figure out which command sequence causes this problem
(due to lack of test hardware), but it's known that increasing the
delay fixes.  So, added a stupid workaround here temporarily...
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

There are two similar GPIO-enablement codes in patch_sigmatel.c.
Let's clean up.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added a new STAC 9205 quirk for Vostro 1500.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added support for advanced power management support for output ports on
92HD7xxx family of codecs. Inactive output ports are powered down when
the pin sense  doesn't detect a connection, and powered back up when a
connection is sensed.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add master controls using vmaster to codecs that have no real hardware
master volume registers.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Moved 2 systems PCI_QUIRK values to STAC_DELL_BIOS. Also the second
front HP jack is incorrect defined in the BIOS VT's for some laptops,
this patch corrects this.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added a mono output mute mixer for the 92hd71bxx family of codecs, this
also removes the need for the mono out node to explicitly unmuted in the
core init.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

This header file exists only for some hacks to adapt alsa-driver
tree.  It's useless for building in the kernel.  Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it.  This should be really killed in
future.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Dynamically create digital gain mixers for dmics that have out-amp
support. Also some 92HD73xx's codecs don't have DMIC gains, so this also
prevents creating dead mixers.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Some laptops incorrectly assume the front input jack as a line in
instead of a microphone in. Which in turn disables the voltage
reference, in which non-amplified input is not possible.  This patch
enables VREF80 for the input jack.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

The digital mux on STAC codecs doesn't always exist although the
driver builds dmux enum mixer elements unconditionally.
Now the driver creates 'digital input source' mixer elements only
when dmux is available.
Also, the patch adds the missing dmux definition for STAC925x.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Cleaned up STAC927x and added several subsystem id's for more laptops.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added more codecs to the 92HD71 family, as well as support for several
that don't have an analog mixer.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Changed hardware gain mixers for the digital mic's from HDA_OUTPUT to
HDA_INPUT.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Added support for new STAC92HD73 family of codecs. Additionally added
features for multiple analog loopbacks, and multiple dmux mixers.
Regression testing for the analog loopback changes for STAC9205 and
STAC9274D completed with any issues, as well for the dmux changes.
Signed-off-by: NMatthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Volume knob controls with STAC codecs seem to cause problems with some
devices.  Volumes change very slowly or silent suddenly.  It's likely
due to conflict between the software and the hardware volume knob
setup.
Since we'll have a virtual master control in future, it's safer to
remove this control completely right now.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Check the value ranges in ctl put callbacks properly so that
invalid values won't be stored or written to registers.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

When a mic jack is set up as the multiple I/O, it may issue the automute
function wrongly.  This patch fixes the wrong automute detection.
Signed-off-by: NJiang Zhe <zhe.jiang@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Dell laptops have multiple HP jacks that can be used for multi-channel
outputs.  The current auto pincfg handles the speaker as the primary
output and thus cannot handle the multi-channel configuration for such
cases.  This patch adds a workaround to fix this issue by swapping the
HP and speaker during multi-channel setup routines.
Signed-off-by: NJiang Zhe <zhe.jiang@intel.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>