On enslave failure primary_slave can point to new_slave which is to be
freed, and the same applies to curr_active_slave. So check if this is
the case and clean up properly after err_detach because that's the first
error code path after they're set.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The main problem is with vid refcount which only gets bumped up.
Delete the vlans after err_detach as that's the first error path
after the vlans are added.
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add bond_mc_list_flush() after err_detach as that's the first error path
after the addresses are added. The main issue is the mc addresses' refcount
which only gets bumped up.

v2: update log message and don't move code unnecessarily
Signed-off-by: NNikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return -EINVAL when tb[TCA_FW_MASK] is set and head->mask != 0xFFFFFFFF
instead of 0 (ifdef CONFIG_NET_CLS_IND and tb[TCA_FW_INDEV]), as done elsewhere
in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "reason" can come from skb->data[] and it hasn't been capped so it
can be from 0-255 instead of just 0-6.  For example in irlmp_state_dtr()
the code does:

	reason = skb->data[3];
	...
	irlmp_disconnect_indication(self, reason, skb);

Also LMREASON has a couple other values which don't have entries in the
irlmp_reasons[] array.  And 0xff is a valid reason as well which means
"unknown".

So far as I can see we don't actually care about "reason" except for in
the debug code.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
If time allows, please consider pulling the following patchset contains two
late Netfilter fixes, they are:

* Skip broadcast/multicast locally generated traffic in the rpfilter,
  (closes netfilter bugzilla #814), from Florian Westphal.

* Fix missing elements in the listing of ipset bitmap ip,mac set
  type with timeout support enabled, from Jozsef Kadlecsik.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

John W. Linville says:

====================
A few stragglers hoping for 3.9, somewhat delayed due to my travels...

On the mac80211 bits, Johannes says:

"Sadly, I have another pull request -- the idle handling fix broke LED
handling in some cases."

and:

"Yet one more!

This fixes a fairly important/annoying bug -- when roaming between
multiple APs of the same network, the system could get stuck thinking it
was connected to the old one while it really wasn't."

On top of that...

Arend sends a brcmfmac patch that removes advertising a feature that
isn't actually fully supported, and a brcmsmac patch that rearranges
code to request firmware at IFF_UP to play more nicely with being
built into the kernel.

Felix gives us a minor ath9k_htc fix to support the newly released
open source firmware, and an ath9k_hw initvals fix to improve device
stability.

Rafał Miłecki provides a fix for an ssb regression that caused a
serious performance problem with b43.

Zefir Kurtisi offers an ath9k fix to change some kmalloc flags to
allow the DFS detector to be called in softirq context.

Please let me know if there are problems.  If these don't make 3.9,
I'll just pull them into wireless-next -- just let me know if you
want to do it that way!
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit bd090dfc (tcp: tcp_replace_ts_recent() should not be called
from tcp_validate_incoming()) introduced a TS ecr bug in slow path
processing.

1 A > B P. 1:10001(10000) ack 1 <nop,nop,TS val 1001 ecr 200>
2 B < A . 1:1(0) ack 1 win 257 <sack 9001:10001,TS val 300 ecr 1001>
3 A > B . 1:1001(1000) ack 1 win 227 <nop,nop,TS val 1002 ecr 200>
4 A > B . 1001:2001(1000) ack 1 win 227 <nop,nop,TS val 1002 ecr 200>

(ecr 200 should be ecr 300 in packets 3 & 4)

Problem is tcp_ack() can trigger send of new packets (retransmits),
reflecting the prior TSval, instead of the TSval contained in the
currently processed incoming packet.

Fix this by calling tcp_replace_ts_recent() from tcp_ack() after the
checks, but before the actions.
Reported-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alex Efros reported rpfilter module doesn't match following packets:
IN=br.qemu SRC=192.168.2.1 DST=192.168.2.255 [ .. ]
(netfilter bugzilla #814).

Problem is that network stack arranges for the locally generated broadcasts
to appear on the interface they were sent out, so the IFF_LOOPBACK check
doesn't trigger.

As -m rpfilter is restricted to PREROUTING, we can check for existing
rtable instead, it catches locally-generated broad/multicast case, too.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

The type when timeout support was enabled, could not list all elements,
just the first ones which could fit into one netlink message: it just
did not continue listing after the first message.
Reported-by: NYoann JUET <yoann.juet@univ-nantes.fr>
Signed-off-by: NJozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Tested-by: NYoann JUET <yoann.juet@univ-nantes.fr>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Since commit 6b923cb7 (bonding: support for IPv6 transmit hashing)
bonding doesn't properly hash traffic in forwarding setups.

Vitaly V. Bursov diagnosed that skb_network_header_len() returned 0 in
this case.

More generally, the transport header might not be in the skb head.

Use pskb_may_pull() & skb_header_pointer() to get it right, and use
proto_ports_offset() in bond_xmit_hash_policy_l34() to get support for
more protocols than TCP and UDP.
Reported-by: NVitaly V. Bursov <vitalyb@telenet.dn.ua>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: John Eaglesham <linux@8192.net>
Tested-by: NVitaly V. Bursov <vitalyb@telenet.dn.ua>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes 2 issues regarding bnx2x's status blocks:

   1. ethtool -c caused corruption of status blocks in FW RAM.

   2. when using multi-CoS, the configuration of the timeout values of
      status blocks is incorrect, harming the coalescing of interrupts
      for such CoSs.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When loading after UNDI (e.g., Boot from SAN) the UNDI does not
gracefully yield its resources; The bnx2x driver handles that release
itself.

During the manipulation required to release those resources, it's possible
for the UNDI to try and write to memory regions which are no longer accessible,
causing the PCI bus to prevent further writes from the chip.

This would in turn cause DMAE timeouts later on in the driver, as the driver
will be unable to use the chip's DMA engines.

This patch prevents the chip from actually writing through the PCI bus
in said scenario, thus allowing the release without the unfortunate by-product.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

Shahed Shaikh says:

====================
This patch series contains bug fixes for -
* Loopback test failure while traffic is running.
* Tx timeout and subsequent firmware reset by removing check for
  '(adapter->netdev->features & (NETIF_F_TSO | NETIF_F_TSO6)' from tx fast
  path, as per Eric's suggestion.
* Typo in logs.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Debug logs were not matching with code functionality.
o Changed dev_info to netdev_err
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When driver receives a packet with gso size > 0 and when TSO is disabled,
it should be transmitted as a TSO packet to prevent Tx timeout and subsequent
firmware reset.
Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before conducting loopback test by sending packets, driver should stop transmit
queue and turn off carrier.
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PF driver does not check if the administrator has already set a VF
VLAN via the PF driver before setting the new VLAN.  This results in
the following scenario:

A) Administrator sets VF <n> to VLAN 100
B) Administrator sets VF <x> to VLAN 100
C) Administrator sets VF <n> to VLAN 200
D) The VF <n> driver continues to be able to receive traffic on VLAN
   100 because the VLVFB pool enable bit for that VF was left set
   instead of being cleared as it should be.

This fix ensures that the old VLAN filter for VF <n> is first removed
and the pool bit enable for VF <n> is cleared so that it no longer
receives traffic on VLAN 100.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch actually reverts:
igb: Support using build_skb in the case that jumbo frames are disabled

The reason for reverting this patch is that it can lead to data corruption.
The following flow was pointed out by Ben Hutchings:

1. skb is forwarded to another device
2. Packet headers are modified and it's put into a queue
3. Second packet is received into the other half of this page
4. Page cannot be reused, so is DMA-unmapped
5. The DMA mapping was non-coherent, so unmap copies or invalidates
cache

The headers added in step 2 get trashed in step 5.
Reported-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Included changes:
- fix MAC address check in case of multiple mesh interfaces
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jesse Gross says:

====================
Two small bug fixes for net/3.9 including the issue previously
discussed where allocation of netlink notifications can fail after
changes have been committed.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On a multi-mesh node (a node running more than one batman-adv
virtual interface) batadv_is_my_mac() has to check MAC
addresses of hard interfaces belonging to the current mesh
only.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Pull Ceph fix from Sage Weil:
 "It's a simple fix for a hard to hit race, but low-risk and clearly
  correct"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: do a safe list traversal in rbd_img_request_submit()

In the very unlikely event where a guest would be foolish enough to
*read* from a write-only cache maintainance register, we end up
with preemption disabled, due to a misplaced get_cpu().

Just move the "is_write" test outside of the critical section.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <cdall@cs.columbia.edu>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It's possible that the reference to the object request dropped
inside the loop in rbd_img_request_submit() will be the last
one, in which case the content of the object pointer can't be
trusted.

Use a safe form of the object request list traversal to avoid
problems.

This resolves:
    http://tracker.ceph.com/issues/4705Signed-off-by: NAlex Elder <elder@inktank.com>
Reviewed-by: NJosh Durgin <josh.durgin@inktank.com>

Pull networking fixes from David Miller:

 1) Fix erroneous netfilter drop of SIP packets generated by some Cisco
    phones, from Patrick McHardy.

 2) Fix netfilter IPSET refcounting in list_set_add(), from Jozsef
    Kadlecsik.

 3) Fix TCP syncookies route lookup key, we don't use the same values we
    would use for the usual SYN receive processing, from Dmitry Popov.

 4) Fix NULL deref in bond_slave_netdev_event(), from Nikolay
    Aleksandrov.

 5) When bonding enslave fails, we can forget to clear the IFF_BONDING
    bit, fix also from Nikolay Aleksandrov.

 6) skb->csum_start is 16-bits, which is almost always just fine.  But
    if we reallocate the headroom of an SKB this can push the
    skb->csum_start value outside of it's valid range.  This can easily
    happen when collapsing multiple SKBs from the retransmit queue
    together.

    Fix from Thomas Graf.

 7) Fix NULL deref in be2net driver due to missing check of
    __vlan_put_tag() return value, from Ivan Vecera.

 8) tun_set_iff() returns zero instead of error code on failure, fix
    from Wei Yongjun.

 9) Like GARP, 802 MRP needs to hold the app->lock when adding MAD
    events and queueing PDUs.  Fix from David Ward.

10) Build fix, MVMDIO needs PHYLIB, from Thomas Petazzoni..

11) Fix mac80211 static with ipv6 modular build, from Cong Wang.

12) If userland specifies a path cost explicitly, do not override it
    when the carrier state changes.  From Stephen Hemminger.

13) mvnets calculates the TX queue to use incorrectly resulting in
    garbage pointer derefs and crashes, fix from Willy Tarreau.

14) cdc_mbim does erroneous sizeof(ETH_HLEN).  Fix from Bjorn Mork.

15) IP fragmentation can leak a refcount-less route out from an RCU
    protected section.  This results in crashes and all sorts of hard to
    diagnose behavior.  Fix from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (24 commits)
  qlcnic: fix beaconing test for 82xx adapter
  net: drop dst before queueing fragments
  net: fec: fix regression in link change accounting
  net: cdc_mbim: remove bogus sizeof()
  drivers: net: ethernet: cpsw: get slave VLAN id from slave node instead of cpsw node
  net: mvneta: fix improper tx queue usage in mvneta_tx()
  esp4: fix error return code in esp_output()
  bridge: make user modified path cost sticky
  ipv6: statically link register_inet6addr_notifier()
  net: mvmdio: add select PHYLIB
  net/802/mrp: fix possible race condition when calling mrp_pdu_queue()
  tuntap: fix error return code in tun_set_iff()
  be2net: take care of __vlan_put_tag return value
  can: sja1000: fix handling on dt properties on little endian systems
  can: mcp251x: add missing IRQF_ONESHOT to request_threaded_irq
  netfilter: nf_nat: fix race when unloading protocol modules
  tcp: Reallocate headroom if it would overflow csum_start
  stmmac: prevent interrupt loop with MMC RX IPC Counter
  bonding: IFF_BONDING is not stripped on enslave failure
  bonding: fix netdev event NULL pointer dereference
  ...

Commit b4cbb197 ("vm: add vm_iomap_memory() helper function") added
a helper function wrapper around io_remap_pfn_range(), and every other
architecture defined it in <asm/pgtable.h>.

The s390 choice of <asm/io.h> may make sense, but is not very convenient
for this case, and gratuitous differences like that cause unexpected errors like this:

   mm/memory.c: In function 'vm_iomap_memory':
   mm/memory.c:2439:2: error: implicit declaration of function 'io_remap_pfn_range' [-Werror=implicit-function-declaration]

Glory be the kbuild test robot who noticed this, bisected it, and
reported it to the guilty parties (ie me).

Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

o Commit 319ecf12
  ("qlcnic: 83xx sysfs routines") introduced regression
  for beaconing test while refactoring 82xx code. This patch is to
  revert code to fix beaconing test for 82xx adapter.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 4a94445c (net: Use ip_route_input_noref() in input path)
added a bug in IP defragmentation handling, as non refcounted
dst could escape an RCU protected section.

Commit 64f3b9e2 (net: ip_expire() must revalidate route) fixed
the case of timeouts, but not the general problem.

Tom Parkin noticed crashes in UDP stack and provided a patch,
but further analysis permitted us to pinpoint the root cause.

Before queueing a packet into a frag list, we must drop its dst,
as this dst has limited lifetime (RCU protected)

When/if a packet is finally reassembled, we use the dst of the very
last skb, still protected by RCU and valid, as the dst of the
reassembled packet.

Use same logic in IPv6, as there is no need to hold dst references.
Reported-by: NTom Parkin <tparkin@katalix.com>
Tested-by: NTom Parkin <tparkin@katalix.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull ARM fix from Russell King:
 "A build fix for an incomplete change to the ARM cpu suspend code"

* branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: Do 15e0d9e3 (ARM: pm: let platforms select cpu_suspend support) properly

Pull kvm fixes from Marcelo Tosatti:
 "PPC and ARM KVM fixes"

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  ARM: KVM: fix L_PTE_S2_RDWR to actually be Read/Write
  ARM: KVM: fix KVM_CAP_ARM_SET_DEVICE_ADDR reporting
  kvm/ppc/e500: eliminate tlb_refs
  kvm/ppc/e500: g2h_tlb1_map: clear old bit before setting new bit
  kvm/ppc/e500: h2g_tlb1_rmap: esel 0 is valid
  kvm/powerpc/e500mc: fix tlb invalidation on cpu migration

Pull powerpc fixes from Stephen Rothwell:
 "Three regresions in the PowerPC code.  One from v3.7 the others from
  this merge window."

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sfr/next-fixes:
  powerpc: add a missing label in resume_kernel
  powerpc: Fix audit crash due to save/restore PPR changes
  powerpc: fix compiling CONFIG_PPC_TRANSACTIONAL_MEM when CONFIG_ALTIVEC=n

Pull kbuild fix from Michal Marek:
 "Fix for a missing dependency when generating scripts/mod/devicetable-offsets.h.
  This dependency got introduced in v3.9-rc1."

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  kbuild: generate generic headers before recursing into scripts

Pull input fixes from Dmitry Torokhov:
 "Two small fixups to the Wacom driver"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: wacom - correct reported resolution for Intuos4 Wireless
  Input: wacom - fix "can not retrieve extra class descriptor" for 24HDT

* 'kvm-arm-fixes-3.9' of git://github.com/columbia/linux-kvm-arm:
  ARM: KVM: fix L_PTE_S2_RDWR to actually be Read/Write
  ARM: KVM: fix KVM_CAP_ARM_SET_DEVICE_ADDR reporting
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Various drivers end up replicating the code to mmap() their memory
buffers into user space, and our core memory remapping function may be
very flexible but it is unnecessarily complicated for the common cases
to use.

Our internal VM uses pfn's ("page frame numbers") which simplifies
things for the VM, and allows us to pass physical addresses around in a
denser and more efficient format than passing a "phys_addr_t" around,
and having to shift it up and down by the page size.  But it just means
that drivers end up doing that shifting instead at the interface level.

It also means that drivers end up mucking around with internal VM things
like the vma details (vm_pgoff, vm_start/end) way more than they really
need to.

So this just exports a function to map a certain physical memory range
into user space (using a phys_addr_t based interface that is much more
natural for a driver) and hides all the complexity from the driver.
Some drivers will still end up tweaking the vm_page_prot details for
things like prefetching or cacheability etc, but that's actually
relevant to the driver, rather than caring about what the page offset of
the mapping is into the particular IO memory region.
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Looks like our L_PTE_S2_RDWR definition is slightly wrong,
and is actually write only (see ARM ARM Table B3-9, Stage 2 control
of access permissions). Didn't make a difference for normal pages,
as we OR the flags together, but I'm still wondering how it worked
for Stage-2 mapped devices, such as the GIC.

Brown paper bag time, again.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <cdall@cs.columbia.edu>

Commit 3401d546 (KVM: ARM: Introduce KVM_ARM_SET_DEVICE_ADDR
ioctl) added support for the KVM_CAP_ARM_SET_DEVICE_ADDR capability,
but failed to add a break in the relevant case statement, returning
the number of CPUs instead.

Luckilly enough, the CONFIG_NR_CPUS=0 patch hasn't been merged yet
(https://lkml.org/lkml/diff/2012/3/31/131/1), so the bug wasn't
noticed.

Just give it a break!
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NChristoffer Dall <cdall@cs.columbia.edu>

A link-down isn't properly saved in the FEC state, so we wouldn't restart the
FEC after a repeated link-up.

Regression was introduced with commit
d97e7497 "net: fec: restart the FEC when PHY speed changes"
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>