Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 161
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 09 8月, 2019 1 次提交
  3. 07 8月, 2019 1 次提交
    • P
      mlxsw: spectrum_dcb: Configure DSCP map as the last rule is removed · d3e36788
      由 Petr Machata 提交于 
      [ Upstream commit dedfde2fe1c4ccf27179fcb234e2112d065c39bb ]

Spectrum systems use DSCP rewrite map to update DSCP field in egressing
packets to correspond to priority that the packet has. Whether rewriting
will take place is determined at the point when the packet ingresses the
switch: if the port is in Trust L3 mode, packet priority is determined from
the DSCP map at the port, and DSCP rewrite will happen. If the port is in
Trust L2 mode, 802.1p is used for packet prioritization, and no DSCP
rewrite will happen.

The driver determines the port trust mode based on whether any DSCP
prioritization rules are in effect at given port. If there are any, trust
level is L3, otherwise it's L2. When the last DSCP rule is removed, the
port is switched to trust L2. Under that scenario, if DSCP of a packet
should be rewritten, it should be rewritten to 0.

However, when switching to Trust L2, the driver neglects to also update the
DSCP rewrite map. The last DSCP rule thus remains in effect, and packets
egressing through this port, if they have the right priority, will have
their DSCP set according to this rule.

Fix by first configuring the rewrite map, and only then switching to trust
L2 and bailing out.

Fixes: b2b1dab6 ("mlxsw: spectrum: Support ieee_setapp, ieee_delapp")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reported-by: NAlex Veber <alexve@mellanox.com>
Tested-by: NAlex Veber <alexve@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
      d3e36788
  5. 14 7月, 2019 1 次提交
  7. 10 7月, 2019 1 次提交
  9. 22 6月, 2019 1 次提交
  11. 17 5月, 2019 4 次提交
    • I
      mlxsw: core: Do not use WQ_MEM_RECLAIM for mlxsw workqueue · e38c6748
      由 Ido Schimmel 提交于 
      [ Upstream commit b442fed1b724af0de087912a5718ddde1b87acbb ]

The workqueue is used to periodically update the networking stack about
activity / statistics of various objects such as neighbours and TC
actions.

It should not be called as part of memory reclaim path, so remove the
WQ_MEM_RECLAIM flag.

Fixes: 3d5479e9 ("mlxsw: core: Remove deprecated create_workqueue")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <alexander.levin@microsoft.com>
      e38c6748
    • I
      mlxsw: core: Do not use WQ_MEM_RECLAIM for mlxsw ordered workqueue · 835ae6cc
      由 Ido Schimmel 提交于 
      [ Upstream commit 4af0699782e2cc7d0d89db9eb6f8844dd3df82dc ]

The ordered workqueue is used to offload various objects such as routes
and neighbours in the order they are notified.

It should not be called as part of memory reclaim path, so remove the
WQ_MEM_RECLAIM flag. This can also result in a warning [1], if a worker
tries to flush a non-WQ_MEM_RECLAIM workqueue.

[1]
[97703.542861] workqueue: WQ_MEM_RECLAIM mlxsw_core_ordered:mlxsw_sp_router_fib6_event_work [mlxsw_spectrum] is flushing !WQ_MEM_RECLAIM events:rht_deferred_worker
[97703.542884] WARNING: CPU: 1 PID: 32492 at kernel/workqueue.c:2605 check_flush_dependency+0xb5/0x130
...
[97703.542988] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
[97703.543049] Workqueue: mlxsw_core_ordered mlxsw_sp_router_fib6_event_work [mlxsw_spectrum]
[97703.543061] RIP: 0010:check_flush_dependency+0xb5/0x130
...
[97703.543071] RSP: 0018:ffffb3f08137bc00 EFLAGS: 00010086
[97703.543076] RAX: 0000000000000000 RBX: ffff96e07740ae00 RCX: 0000000000000000
[97703.543080] RDX: 0000000000000094 RSI: ffffffff82dc1934 RDI: 0000000000000046
[97703.543084] RBP: ffffb3f08137bc20 R08: ffffffff82dc18a0 R09: 00000000000225c0
[97703.543087] R10: 0000000000000000 R11: 0000000000007eec R12: ffffffff816e4ee0
[97703.543091] R13: ffff96e06f6a5c00 R14: ffff96e077ba7700 R15: ffffffff812ab0c0
[97703.543097] FS: 0000000000000000(0000) GS:ffff96e077a80000(0000) knlGS:0000000000000000
[97703.543101] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[97703.543104] CR2: 00007f8cd135b280 CR3: 00000001e860e003 CR4: 00000000003606e0
[97703.543109] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[97703.543112] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[97703.543115] Call Trace:
[97703.543129] __flush_work+0xbd/0x1e0
[97703.543137] ? __cancel_work_timer+0x136/0x1b0
[97703.543145] ? pwq_dec_nr_in_flight+0x49/0xa0
[97703.543154] __cancel_work_timer+0x136/0x1b0
[97703.543175] ? mlxsw_reg_trans_bulk_wait+0x145/0x400 [mlxsw_core]
[97703.543184] cancel_work_sync+0x10/0x20
[97703.543191] rhashtable_free_and_destroy+0x23/0x140
[97703.543198] rhashtable_destroy+0xd/0x10
[97703.543254] mlxsw_sp_fib_destroy+0xb1/0xf0 [mlxsw_spectrum]
[97703.543310] mlxsw_sp_vr_put+0xa8/0xc0 [mlxsw_spectrum]
[97703.543364] mlxsw_sp_fib_node_put+0xbf/0x140 [mlxsw_spectrum]
[97703.543418] ? mlxsw_sp_fib6_entry_destroy+0xe8/0x110 [mlxsw_spectrum]
[97703.543475] mlxsw_sp_router_fib6_event_work+0x6cd/0x7f0 [mlxsw_spectrum]
[97703.543484] process_one_work+0x1fd/0x400
[97703.543493] worker_thread+0x34/0x410
[97703.543500] kthread+0x121/0x140
[97703.543507] ? process_one_work+0x400/0x400
[97703.543512] ? kthread_park+0x90/0x90
[97703.543523] ret_from_fork+0x35/0x40

Fixes: a3832b31 ("mlxsw: core: Create an ordered workqueue for FIB offload")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NSemion Lisyansky <semionl@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <alexander.levin@microsoft.com>
      835ae6cc
    • I
      mlxsw: core: Do not use WQ_MEM_RECLAIM for EMAD workqueue · 880a328e
      由 Ido Schimmel 提交于 
      [ Upstream commit a8c133b06183c529c51cd0d54eb57d6b7078370c ]

The EMAD workqueue is used to handle retransmission of EMAD packets that
contain configuration data for the device's firmware.

Given the workers need to allocate these packets and that the code is
not called as part of memory reclaim path, remove the WQ_MEM_RECLAIM
flag.

Fixes: d965465b ("mlxsw: core: Fix possible deadlock")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <alexander.levin@microsoft.com>
      880a328e
    • I
      mlxsw: spectrum_switchdev: Add MDB entries in prepare phase · a80f62f7
      由 Ido Schimmel 提交于 
      [ Upstream commit d4d0e40977ac450f32f2db5e4d8e23c9d2578899 ]

The driver cannot guarantee in the prepare phase that it will be able to
write an MDB entry to the device. In case the driver returned success
during the prepare phase, but then failed to add the entry in the commit
phase, a WARNING [1] will be generated by the switchdev core.

Fix this by doing the work in the prepare phase instead.

[1]
[  358.544486] swp12s0: Commit of object (id=2) failed.
[  358.550061] WARNING: CPU: 0 PID: 30 at net/switchdev/switchdev.c:281 switchdev_port_obj_add_now+0x9b/0xe0
[  358.560754] CPU: 0 PID: 30 Comm: kworker/0:1 Not tainted 5.0.0-custom-13382-gf2449babf221 #1350
[  358.570472] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016
[  358.580582] Workqueue: events switchdev_deferred_process_work
[  358.587001] RIP: 0010:switchdev_port_obj_add_now+0x9b/0xe0
...
[  358.614109] RSP: 0018:ffffa6b900d6fe18 EFLAGS: 00010286
[  358.619943] RAX: 0000000000000000 RBX: ffff8b00797ff000 RCX: 0000000000000000
[  358.627912] RDX: ffff8b00b7a1d4c0 RSI: ffff8b00b7a152e8 RDI: ffff8b00b7a152e8
[  358.635881] RBP: ffff8b005c3f5bc0 R08: 000000000000022b R09: 0000000000000000
[  358.643850] R10: 0000000000000000 R11: ffffa6b900d6fcc8 R12: 0000000000000000
[  358.651819] R13: dead000000000100 R14: ffff8b00b65a23c0 R15: 0ffff8b00b7a2200
[  358.659790] FS:  0000000000000000(0000) GS:ffff8b00b7a00000(0000) knlGS:0000000000000000
[  358.668820] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  358.675228] CR2: 00007f00aad90de0 CR3: 00000001ca80d000 CR4: 00000000001006f0
[  358.683188] Call Trace:
[  358.685918]  switchdev_port_obj_add_deferred+0x13/0x60
[  358.691655]  switchdev_deferred_process+0x6b/0xf0
[  358.696907]  switchdev_deferred_process_work+0xa/0x10
[  358.702548]  process_one_work+0x1f5/0x3f0
[  358.707022]  worker_thread+0x28/0x3c0
[  358.711099]  ? process_one_work+0x3f0/0x3f0
[  358.715768]  kthread+0x10d/0x130
[  358.719369]  ? __kthread_create_on_node+0x180/0x180
[  358.724815]  ret_from_fork+0x35/0x40

Fixes: 3a49b4fd ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NAlex Kushnarov <alexanderk@mellanox.com>
Tested-by: NAlex Kushnarov <alexanderk@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <alexander.levin@microsoft.com>
      a80f62f7
  13. 02 5月, 2019 3 次提交
  15. 06 4月, 2019 1 次提交
    • F
      mlxsw: spectrum: Avoid -Wformat-truncation warnings · a64ffbaf
      由 Florian Fainelli 提交于 
      [ Upstream commit ab2c4e2581ad32c28627235ff0ae8c5a5ea6899f ]

Give precision identifiers to the two snprintf() formatting the priority
and TC strings to avoid producing these two warnings:

drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_prio_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:37: warning: '%d'
directive output may be truncated writing between 1 and 3 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
   snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
                                     ^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2132:3: note: 'snprintf'
output between 3 and 36 bytes into a destination of size 32
   snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     mlxsw_sp_port_hw_prio_stats[i].str, prio);
     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function
'mlxsw_sp_port_get_tc_strings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:37: warning: '%d'
directive output may be truncated writing between 1 and 11 bytes into a
region of size between 0 and 31 [-Wformat-truncation=]
   snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
                                     ^~
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2143:3: note: 'snprintf'
output between 3 and 44 bytes into a destination of size 32
   snprintf(*p, ETH_GSTRING_LEN, "%s_%d",
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
     mlxsw_sp_port_hw_tc_stats[i].str, tc);
     ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
      a64ffbaf
  17. 27 2月, 2019 3 次提交
  19. 23 2月, 2019 1 次提交
  21. 13 2月, 2019 2 次提交
    • I
      mlxsw: spectrum: Properly cleanup LAG uppers when removing port from LAG · b124f086
      由 Ido Schimmel 提交于 
      [ Upstream commit be2d6f421f680e01d58f7cd452646e0d8586d49b ]

When a LAG device or a VLAN device on top of it is enslaved to a bridge,
the driver propagates the CHANGEUPPER event to the LAG's slaves.

This causes each physical port to increase the reference count of the
internal representation of the bridge port by calling
mlxsw_sp_port_bridge_join().

However, when a port is removed from a LAG, the corresponding leave()
function is not called and the reference count is not decremented. This
leads to ugly hacks such as mlxsw_sp_bridge_port_should_destroy() that
try to understand if the bridge port should be destroyed even when its
reference count is not 0.

Instead, make sure that when a port is unlinked from a LAG it would see
the same events as if the LAG (or its uppers) were unlinked from a
bridge.

The above is achieved by walking the LAG's uppers when a port is
unlinked and calling mlxsw_sp_port_bridge_leave() for each upper that is
enslaved to a bridge.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
      b124f086
    • N
      mlxsw: spectrum_acl: Limit priority value · 702286d3
      由 Nir Dotan 提交于 
      [ Upstream commit d7263ab35be25505ab57ebecd93cbc5dba8be717 ]

In Spectrum-2, higher priority value wins and priority valid values are in
the range of {1,cap_kvd_size-1}. mlxsw_sp_acl_tcam_priority_get converts
from lower-bound priorities alike tc flower to Spectrum-2 HW range. Up
until now tc flower did not provide priority 0 or reached the maximal
value, however multicast routing does provide priority 0.

Therefore, Change mlxsw_sp_acl_tcam_priority_get to verify priority is in
the correct range. Make sure priority is never set to zero and never
exceeds the maximal allowed value.
Signed-off-by: NNir Dotan <nird@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
      702286d3
  23. 31 1月, 2019 3 次提交
    • I
      mlxsw: pci: Ring CQ's doorbell before RDQ's · bdafc159
      由 Ido Schimmel 提交于 
      When a packet should be trapped to the CPU the device consumes a WQE
(work queue element) from an RDQ (receive descriptor queue) and copies
the packet to the address specified in the WQE. The device then tries to
post a CQE (completion queue element) that contains various metadata
(e.g., ingress port) about the packet to a CQ (completion queue).

In case the device managed to consume a WQE, but did not manage to post
the corresponding CQE, it will get stuck. This unlikely situation can be
triggered due to the scheme the driver is currently using to process
CQEs.

The driver will consume up to 512 CQEs at a time and after processing
each corresponding WQE it will ring the RDQ's doorbell, letting the
device know that a new WQE was posted for it to consume. Only after
processing all the CQEs (up to 512), the driver will ring the CQ's
doorbell, letting the device know that new ones can be posted.

Fix this by having the driver ring the CQ's doorbell for every processed
CQE, but before ringing the RDQ's doorbell. This guarantees that
whenever we post a new WQE, there is a corresponding CQE available. Copy
the currently processed CQE to prevent the device from overwriting it
with a new CQE after ringing the doorbell.

Note that the driver still arms the CQ only after processing all the
pending CQEs, so that interrupts for this CQ will only be delivered
after the driver finished its processing.

Before commit 8404f6f2 ("mlxsw: pci: Allow to use CQEs of version 1
and version 2") the issue was virtually impossible to trigger since the
number of CQEs was twice the number of WQEs and the number of CQEs
processed at a time was equal to the number of available WQEs.

Fixes: 8404f6f2 ("mlxsw: pci: Allow to use CQEs of version 1 and version 2")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NSemion Lisyansky <semionl@mellanox.com>
Tested-by: NSemion Lisyansky <semionl@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      bdafc159
    • N
      mlxsw: spectrum_fid: Update dummy FID index · c82f4684
      由 Nir Dotan 提交于 
      [ Upstream commit a11dcd6497915ba79d95ef4fe2541aaac27f6201 ]

When using a tc flower action of egress mirred redirect, the driver adds
an implicit FID setting action. This implicit action sets a dummy FID to
the packet and is used as part of a design for trapping unmatched flows
in OVS.  While this implicit FID setting action is supposed to be a NOP
when a redirect action is added, in Spectrum-2 the FID record is
consulted as the dummy FID index is an 802.1D FID index and the packet
is dropped instead of being redirected.

Set the dummy FID index value to be within 802.1Q range. This satisfies
both Spectrum-1 which ignores the FID and Spectrum-2 which identifies it
as an 802.1Q FID and will then follow the redirect action.

Fixes: c3ab4354 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: NNir Dotan <nird@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      c82f4684
    • N
      mlxsw: pci: Increase PCI SW reset timeout · bc4e2300
      由 Nir Dotan 提交于 
      [ Upstream commit d2f372ba0914e5722ac28e15f2ed2db61bcf0e44 ]

Spectrum-2 PHY layer introduces a calibration period which is a part of the
Spectrum-2 firmware boot process. Hence increase the SW timeout waiting for
the firmware to come out of boot. This does not increase system boot time
in cases where the firmware PHY calibration process is done quickly.

Fixes: c3ab4354 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: NNir Dotan <nird@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      bc4e2300
  25. 26 1月, 2019 2 次提交
  27. 10 1月, 2019 1 次提交
    • S
      mlxsw: core: Increase timeout during firmware flash process · af93ac09
      由 Shalom Toledo 提交于 
      [ Upstream commit cf0b70e71b32137ccf9c1f3dd9fb30cbf89b4322 ]

During the firmware flash process, some of the EMADs get timed out, which
causes the driver to send them again with a limit of 5 retries. There are
some situations in which 5 retries is not enough and the EMAD access fails.
If the failed EMAD was related to the flashing process, the driver fails
the flashing.

The reason for these timeouts during firmware flashing is cache misses in
the CPU running the firmware. In case the CPU needs to fetch instructions
from the flash when a firmware is flashed, it needs to wait for the
flashing to complete. Since flashing takes time, it is possible for pending
EMADs to timeout.

Fix by increasing EMADs' timeout while flashing firmware.

Fixes: ce6ef68f ("mlxsw: spectrum: Implement the ethtool flash_device callback")
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      af93ac09
  29. 21 12月, 2018 1 次提交
    • I
      mlxsw: spectrum_switchdev: Fix VLAN device deletion via ioctl · 8175f9d3
      由 Ido Schimmel 提交于 
      [ Upstream commit 993107fe ]

When deleting a VLAN device using an ioctl the netdev is unregistered
before the VLAN filter is updated via ndo_vlan_rx_kill_vid(). It can
lead to a use-after-free in mlxsw in case the VLAN device is deleted
while being enslaved to a bridge.

The reason for the above is that when mlxsw receives the CHANGEUPPER
event, it wrongly assumes that the VLAN device is no longer its upper
and thus destroys the internal representation of the bridge port despite
the reference count being non-zero.

Fix this by checking if the VLAN device is our upper using its real
device. In net-next I'm going to remove this trick and instead make
mlxsw completely agnostic to the order of the events.

Fixes: c57529e1 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>
      8175f9d3
  31. 23 11月, 2018 1 次提交
  33. 04 11月, 2018 2 次提交
  35. 18 10月, 2018 1 次提交
  37. 05 10月, 2018 2 次提交
  39. 20 9月, 2018 1 次提交
  41. 05 9月, 2018 1 次提交
    • P
      mlxsw: spectrum_buffers: Set up a dedicated pool for BUM traffic · 3a3539cd
      由 Petr Machata 提交于 
      MC-aware mode was recently enabled by mlxsw on Spectrum switches in
commit 7b819530 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw
ports"). Unfortunately, testing has shown that the fix is incomplete and
in the presented form actually makes the problem even worse, because any
amount of MC traffic causes UC disruption.

The reason for this is that currently, mlxsw configures the MC-specific
TCs (8..15) to map to pool 0. It also configures a maximum buffer size
of 0, but for MC traffic that maximum is disregarded and not part of the
quota. Therefore MC traffic is always admitted to the egress buffer.

Fix the configuration by directing the MC TCs into pool 15, which is
dedicated to MC traffic and recognized as such by the silicon.

Fixes: 7b819530 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      3a3539cd
  43. 26 8月, 2018 1 次提交
    • I
      mlxsw: spectrum_switchdev: Do not leak RIFs when removing bridge · 602b74ed
      由 Ido Schimmel 提交于 
      When a bridge device is removed, the VLANs are flushed from each
configured port. This causes the ports to decrement the reference count
on the associated FIDs (filtering identifier). If the reference count of
a FID is 1 and it has a RIF (router interface), then this RIF is
destroyed.

However, if no port is member in the VLAN for which a RIF exists, then
the RIF will continue to exist after the removal of the bridge. To
reproduce:

# ip link add name br0 type bridge vlan_filtering 1
# ip link set dev swp1 master br0
# ip link add link br0 name br0.10 type vlan id 10
# ip address add 192.0.2.0/24 dev br0.10
# ip link del dev br0

The RIF associated with br0.10 continues to exist.

Fix this by iterating over all the bridge device uppers when it is
destroyed and take care of destroying their RIFs.

Fixes: 99f44bb3 ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      602b74ed
  45. 22 8月, 2018 1 次提交
  47. 11 8月, 2018 2 次提交
  49. 10 8月, 2018 2 次提交