Before we get all the chain (ie. mac80211, cfg80211, nl80211 and
userspace) changed to support net-detect, we can use this debugfs
entry for easy testing and as a proof of concept.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The net-detect feature will require a scan offload to be started in
the same way it is done now for scheduled scan.  Spin a new function
off of the sched_scan_start op code for reuse.  Additionally,
restructure the function a bit for more readability.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Move iwl_mvm_max_scan_ie_len function to scan.c and fix the
implementation to conform with the LMAC scan API.
Since the correct implementation would leave us with unacceptably
tiny probes, add a workaround which returns a larger value.
In current implementation it's possible that unified_scan_lmac and
unified_sched_scan_lmac would return -ENOBUFS.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Improve the initial tx rate and antenna selection to be based on
the rssi of the last rx. This avoids starting at the lowest legacy
rate always and requiring more tx traffic to "climb" up the rates.
Since this option might cause trouble in certain setups, allow to
disable it by default.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When read, this new debugfs entry requests the current temperature
from the firmware and outputs it.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The scheduler is a HW sub-block that directs the work of the Flow
Handler by issuing requests for frame transfers, specifying source
and destination. Its primary function is to allocate flows into the
TX FIFOs based upon a pre-determined mapping.

The driver has some responsibilities to the scheduler, namely
initialising and maintaining the hardware registers. This is
currently done by directly accessing them, which can cause races
with the firmware also accessing the registers.

To address this problem, change the driver to no longer directly
access the registers but go through the firmware for this if the
firmware has support for DQA and thus the new command.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The time event used for CSA GO will also be used by CSA client.
Rename the symbols to something more generic and aligned with the
firmware code.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The upcoming TDLS channel-switch functionality is big enough to warrant
a separate file. Move existing related functions to the new file.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In some testing configuration, the firmware restart flow is
not enabled. Allow to collect logs even in this case.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Reading the temperature directly from the hardware, without the help
of the firmware, is a complex process and is not entirely the same for
different hardware.  Also, some NICs don't easily allow access to the
sensors when the firmware is not running, which would add even more
complexity to the code.

To reduce the code complexity and to avoid code duplication between
the firmware and the driver, boot the firmware briefly to read the
current temperature while in CT kill mode.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A lot of the newer d0i3 ref additions weren't added to the
debugfs file, fix that and add a comment to remember to do
it in the future.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When updating quota in the firmware, it has to reset quite a bit
of internal state, which apparently can have an adverse impact on
its operation.

Avoid that by only updating the quota command when there are any
signification changes, i.e. added/removed bindings or changes in
quota that are bigger than 8 TU within a binding.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The queue handling is a bit unclear - we have an array for
stop_count[IWL_MAX_HW_QUEUES] but indices really are the
mac80211 queue numbers. Change the array to be only of the
right size for mac80211 queues (IEEE80211_MAX_QUEUES) and
rename it to be clearer.

While at it, also remove the unused transport queue stop
bitmap in mvm.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Move all FIFO definitions together into the firmware API
header file and use the same enum/naming scheme for the
command FIFO.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware would like to have a MAC context (unassoc)
before the AP station is removed (we do this) but would
like to keep the BSSID until after it is removed, so we
need to send two commands - one with the BSSID before
and one without the BSSID after.

In order to do this, we need to store the BSSID as it
will have been cleared by mac80211 by the time we get
notified of the disassociation. Also pass it around as
an override to the various functions needing it, and
keep taking it from the mac80211 data otherwise. This
avoids having to keep track of the BSSID in all modes.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.

For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We need to disable PS when a monitor vif is active or, in the future,
when a channel switch is happening.  Add a boolean to mvmvif that
allows PS to be disabled generically.  Additionally, make the monitor
interface use this new flag when it gets activated.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a new iwl_mvm_power_update_ps() function that allows only ps to be
updated according to changes in the vifs.  This allows us to disable
ps only without affecting the pm values of the vifs (and to avoid
sending unnecessary MAC_PM_POWER_TABLE commands to the firmware).
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Aggregations hit latency so disable it by default on
low latency vifs for now. Enable control over this behavior and
allow control over the max frames in an AMPDU in low latency
vifs via debugfs.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to make debugging easier, add an entry to export the
ps_disabled value via debugfs.  To make usage of the
debugfs_create_*() function easier, change the ps_disabled element to
u8.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

By default, when uapsd is not used, the ucode uses
null data packet to exit power-save and get then
pending frames.

However, some tests require the explicit usage of ps-poll.
Allow setting use_ps_poll power option (through debugfs)
to configure the ucode to use ps-poll instead.

The ucode configuration is done by setting the advanced-pm
flag while setting all the ACs to non-upasd mode.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to force the GO to use protection and enhances
the reliability of the link.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add ability to set the NIC's temperature and ignore the actual temperature
that the FW supplies.
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The mvm op_mode won't allocate the buffer for the transport
any more. The transport allocates its own buffer and mvm
is in charge of splicing the buffers in the debugfs hook.

This makes the repartition easier to handle.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

According to new requirements, the ACK / CTS kill mask is
not related to reduced TX power anymore. This allows to
remove the code that tracked reduced TX power enablement
across different interfaces.
The ACK / CTS kill mask is now fetch from a table. It
depends on the Activity grading (activity from BT) and on
the Look Up Table (LUT) type.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The Remain On Channel framework added to the firmare is
a bit like time events. It allows the driver to request
the firmware to be on a certain channel for a certain time.
Unlike the time events, the ROC infrastructure doesn't need
a MAC context in the firmware - it uses a generic context
called "auxiliary framework".

This is useful for any offchannel activity that is not bound
to a specific MAC.
The flow is synchronized much like with time events:
1) The driver receives an action frame from the wpa_supplicant
   via nl80211 that requests to be sent offchannel.
2) The driver sends an Aux ROC command (0x53) to the firmware.
3) The firmware responds with the unique id of the time event.
4) When time event starts, the driver puts the frame in the
   Aux queue.

Special care needs to be taken when the time events ends:
the queue needs to be cleaned-up.
Signed-off-by: NAriej Marjieh <ariej.marjieh@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add iwl_mvm_ref_sync() calls (with new ref types) to
flows that might access the device directly.

These calls make sure the device is out of d0i3,
and the bus is available for direct access.

Since some of these functions are reentrant, convert
the refs_bitmap to a ref counter, so multiple refs
of the same type could be taken concurrently.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The FW does not support PSM on a vif with associated TDLS peers. Disable
PSM when the first peer joins and re-enable it when the last leaves.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

HW/FW constraints dictate that TDLS should only be used when a single
phy ctx is active. We also support at most 4 TDLS peers. We don't
support TDLS on a P2P vif.

Unify and move a phy-ctx counting implementation from the power-mgmt code
in order to simplify implementation.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

An AP/GO may perform the channel switch slightly before its stations.
This scenario may result in packet loss, since the transmission may start
before the client is actually on a new channel. In order to prevent
potential packet loss disable tx to all the stations when the channel
switch flow starts. Clear the disable_tx bit when a station is seen on a
target channel, or after IWL_MVM_CS_UNBLOCK_TX_TIMEOUT beacons on a new
channel. In addition call ieee80211_sta_block_awake in order to inform
mac80211 that the frames for this station should be buffered.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

According to the spec, GO/AP should perform the channel switch just
before "beacon 0". However, since the exact timing isn't defined,
it may result in a sudden GO disappearance from the channel.
Prevent potential packet loss when performing the CS by scheduling
NoA time event and executing the channel switch flow when a notification
from fw is received.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently mvm->csa_vif is protected with mvm mutex. The RCU protection
is required for "iwlwifi: mvm: Reflect GO channel switch in NoA" patch.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Implement the switch_vif_chanctx operation with support for a
single-vif and SWAP mode.  The REASSIGN mode and multi-vifs are not
supported yet.

This operation needs to implement 4 steps, namely unassign, remove,
add and assign the chanctx.  In order to do this, split out these
operations into locked and non-locked parts, thus allowing us to call
them while locked.

Additionally, in order to allow us to restart the hardware when
something fails, add a boolean to the iwl_mvm_nic_restart() function
that tells whether the restart was triggered by a FW error or
something else.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

It turns out that adding the update type argument was pointless as
quota update is never called from the add_interface() callback.
Therefore, IWL_MVM_QUOTA_UPDATE_TYPE_NEW isn't actually needed and
then only a "disabled_vif" argument is needed for the upcoming CSA
work.

Remove the whole enum iwl_mvm_quota_update_type and pass the right
arguments (always NULL for disabled vif right now) to the function
in all current call sites.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In some cases (e.g. when we're doing a channel switch), we may need to
disable the quota of a vif temporarily.  In order to do so, add an
argument to the iwl_mvm_update_quotas() function to tell if the passed
vif is a new one or if it should be disregarded.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add new scan API that uses the same command 0x51 for both regular and
sched scan.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Start the new BT Coex implementation.
Don't react to notifications for now - only the initial
configuration is implemented. The rest will happen in next
patches.
Since coex.c now uses the new the new structures in all
functions, we need to adapt the code to compile, even if it
doesn't run yet.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A new API is coming. This new API is not backward
compatible. So we need to keep the old commands to be able
to work with the former API.
Move all the current code into a new file: coex_legacy.
If a firmware with the new API is detected, we currently
just bail out since the implementation of the new API will
come in future patches.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This patch makes sure there're no target accesses in the add
interface flow before d0i3 exit completes.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>