The BIOS can leave the CHV display PHY in some odd state where
some of the LDOs/lanes won't power down fully when unused. This
will trigger a host of asserts that were added in:
30142273 drm/i915: Add CHV PHY LDO power sanity checks
6669e39f drm/i915: Add some CHV DPIO lane power state asserts

To avoid that, skip the asserts until the PHY power well has been
disabled at least once. That will fully reset the PHY, and once
brought back up, the dynamic power down features will work correctly.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The docs are unclear as usual, so it's not clear whether LRC should be
bypassed, performed normally or GRC code should be used as the LRC code.
Some old docs stated that LRC bypass ought to be used, more recent ones
no longer say that. Some docs indicated that we could use GRC as the LRC
code on CHV, but the BIOS doesn't do that, so let's not do it either.

Besides to enable LRC bypass properly, I believe we should set the bit
already before deasserting cmnreset.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S<deepak.s@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For all the encoders, call the hot_plug if it is registered.
This is required for connected boot and resume cases to generate
fake hpd resulting in reading of edid.
Removing the initial sdvo hot_plug call too so that it will be called
just once from this loop.
Signed-off-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to call intel_runtime_pm_put() and mutex_unlock() before
returning.

Fixes: 7cb5dff8 ('drm/i915: fix task reference leak in i915_debugfs.c')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NGeliang Tang <geliangtang@163.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Latest VBT mentions which set of registers will be used for BLC,
as controller number field. Making use of this field in BXT
BLC implementation. Also, the registers are used in case control
pin indicates display DDI. Adding a check for this.
According to Bspec, BLC_PWM_*_2 uses the display utility pin for output.
To use backlight 2, enable the utility pin with mode = PWM
   v2: Jani's review comments
   addressed
       - Add a prefix _ to BXT BLC registers definitions.
       - Add "bxt only" comment for u8 controller
       - Remove control_pin check for DDI controller
       - Check for valid controller values
       - Set pipe bits in UTIL_PIN_CTL
       - Enable/Disable UTIL_PIN_CTL in enable/disable_backlight()
       - If BLC 2 is used, read active_low_pwm from UTIL_PIN polarity
   Satheesh's review comment addressed
       - If UTIL PIN is already enabled, BIOS would have programmed it. No
       need to disable and enable again.
   v3: Jani's review comments
       - add UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK
       - Disable UTIL_PIN if controller 1 is used
       - Mask out UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK before enabling
       UTIL_PIN
       - check valid controller value in intel_bios.c
       - add backlight.util_pin_active_low
       - disable util pin before enabling
   v4: Change for BXT-PO branch:
   Stubbed unwanted definition which was existing before
   because of DC6 patch.
   UTIL_PIN_MODE_PWM     (0x1b << 24)

v2: Fixed Jani's review comment.

v3: Split the backight PWM frequency programming into separate patch,
    in cases BIOS doesn't initializes it.

v4: Starting afresh and not modifying existing state for backlight, as
    per Jani's recommendation.

v5: Fixed Jani's review comment wrt util pin enable
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Signed-off-by: NSunil Kamath <sunil.kamath@intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

BXT's DSI PLL is different from that of VLV. So this patch
adds a new function to get the current DSI pixel clock based
on the PLL divider ratio and lane count.

This function is required for intel_dsi_get_config() function.

v2: Fixed Jani's review comments.
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Pick appropriate port control register (BXT or VLV), based on device.
Get the current hw state wrt Mipi port.

v2: Rebased on latest drm nightly branch.

v3: Removed the GET_DSI_PORT_CTRL Macro for consistency with earlier
    implementations as per Jani's suggestion.
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch contains changes to support DSI disble sequence in BXT.
The changes are:
1. BXT specific changes in clear_device_ready function.
2. BXT specific changes in DSI disable and post-disable functions.
3. Add a new function to reset BXT Dphy clock and dividers
   (bxt_dsi_reset_clocks).
4. Moved some part of the vlv clock reset code, in a new function
   (vlv_dsi_reset_clocks) maintaining the exact same sequence.
5. Wrapper function to call corresponding reset clock function.

v2: Fixed Jani's review comments.

v3: Removed the GET_DSI_PORT_CTRL Macro for consistency with earlier
    implementations as per Jani's suggestion.
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

BXT DSI clocks are different than previous platforms. So adding a
new function to program following clocks and dividers:
1. Program variable divider to generate input to Tx clock divider
   (Output value must be < 39.5Mhz)
2. Select divide by 2 option to get < 20Mhz for Tx clock
3. Program 8by3 divider to generate Rx clock

v2: Fixed Jani's review comments. Adjusted the Macro definition as
    per convention. Simplified the logic for bit definitions for
    MIPI PORT A and PORT C in same registers.

v3: Refactored the macros for TX, RX Escape and DPHY clocks as per
    Jani's suggestion.

v4: Addressed Jani's review comments.
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch contains following changes:
1. MIPI device ready changes to support dsi_pre_enable. Changes
   are specific to BXT device ready sequence. Added check for
   ULPS mode(No effects on VLV).
2. Changes in dsi_enable to pick BXT port control register.
3. Changes in dsi_pre_enable to restrict DPIO programming for VLV

v2: Fixed Jani's review comments. Removed the changes in VLV/CHV
    code. Fixed the macros to get proper port offsets.

v3: Rebased on latest drm-nightly branch. Fixed Jani's review comments.
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

SKL and BXT qualifies the HAS_DDI() check, and hence haswell
modeset functions are re-used for modeset sequence. But DDI
interface doesn't include support for DSI.
This patch adds:
1. cases for DSI encoder, in those modeset functions and allows
   a CRTC modeset
2. Adds call to pre_pll enabled from CRTC modeset function. Nothing
   needs to be done as such in CRTC for DSI encoder, as PLL, clock
   and and transcoder programming will be taken care in encoder's
   pre_enable and pre_pll_enable function.

v2: Fixed Jani's review comments. Added INVALID_PORT for non DDI
    encoder like DSI for platforms having HAS_DDI as true.

v3: Rebased on latest drm-nightly branch. Added a WARN_ON for invalid
    encoder.

v4: WARN_ON for invalid encoder is refactored as per Jani's suggestion.
    Fixed the sequence for pre_pll_enable.

v5: Protected DDI code paths in case of DSI encoder calls.
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This register was added on GEN4, by the name INSTDONE_1 whereas the GEN6
specification calls it INSTDONE_2. Keep the original name with a
platform prefix to make it clearer which INSTDONE register instance this
is. Also add a comment about the SNB alternative name.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have a bunch of INSTDONE registers for different platforms and
purposes and it's not immediately clear which instance they are just by
looking at the register name. This one was added on GEN2, where it was
the only INSTDONE register, so mark it as such.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We use 3 different names to refer to the same render ring INSTDONE
register. This can be confusing when comparing two parts of the code
accessing the register via different names. Although the GEN4 version's
layout is different, we treat it the same way as the GEN7+ version, in
that we simply read it out during error capture. So remove the
duplicates and leave a comment about the GEN4 difference.

Note that there is also a GEN2 version of this register, but that's on a
different address so not handled in this patch.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There are some allocations that must be only referenced by 32-bit
offsets. To limit the chances of having the first 4GB already full,
objects not requiring this workaround use DRM_MM_SEARCH_BELOW/
DRM_MM_CREATE_TOP flags

In specific, any resource used with flat/heapless (0x00000000-0xfffff000)
General State Heap (GSH) or Instruction State Heap (ISH) must be in a
32-bit range, because the General State Offset and Instruction State
Offset are limited to 32-bits.

Objects must have EXEC_OBJECT_SUPPORTS_48B_ADDRESS flag to indicate if
they can be allocated above the 32-bit address range. To limit the
chances of having the first 4GB already full, objects will use
DRM_MM_SEARCH_BELOW + DRM_MM_CREATE_TOP flags when possible.

The libdrm user of the EXEC_OBJECT_SUPPORTS_48B_ADDRESS flag is here:
http://lists.freedesktop.org/archives/intel-gfx/2015-September/075836.html

v2: Changed flag logic from neeeds_32b, to supports_48b.
v3: Moved 48-bit support flag back to exec_object. (Chris, Daniel)
v4: Split pin flags into PIN_ZONE_4G and PIN_HIGH; update PIN_OFFSET_MASK
to use last PIN_ defined instead of hard-coded value; use correct limit
check in eb_vma_misplaced. (Chris)
v5: Don't touch PIN_OFFSET_MASK and update workaround comment (Chris)
v6: Apply pin-high for ggtt too (Chris)
v7: Handle simultaneous pin-high and pin-mappable end correctly (Akash)
    Fix check for entries currently using +4GB addresses, use min_t and
    other polish in object_bind_to_vm (Chris)
v8: Commit message updated to point to libdrm patch.
v9: vmas are allocated in the correct ozone, so only check flag when the
    vma has not been allocated. (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v4)
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Due to flip interrupts GuC stays awake always and GT does not enter
RC6. Do not route those interrupts to GuC for now. Driver won't touch
DE_GUCRMR register and leave it as what default value.
Signed-off-by: NSagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: NAlex Dai <yu.dai@intel.com>
Reviewed-by: NTom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Use SKL_DPLLx symbolic names instead of raw numbers
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Don't forget to actually check the cstate->active value when
    tallying up the number of active CRTC's.  (Ander)
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We already ensure that pstate->visible = false when crtc->active = false
during runtime programming; make sure we follow the same logic when
reading out initial hardware state.
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Calculate pipe watermarks during atomic calculation phase, based on the
contents of the atomic transaction's state structure.  We still program
the watermarks at the same time we did before, but the computation now
happens much earlier.

While this patch isn't too exciting by itself, it paves the way for
future patches.  The eventual goal (which will be realized in future
patches in this series) is to calculate multiple sets up watermark
values up front, and then program them at different times (pre- vs
post-vblank) on the platforms that need a two-step watermark update.

While we're at it, s/intel_compute_pipe_wm/ilk_compute_pipe_wm/ since
this function only applies to ILK-style watermarks and we have a
completely different function for SKL-style watermarks.

Note that the original code had a memcmp() in ilk_update_wm() to avoid
calling ilk_program_watermarks() if the watermarks hadn't changed.  This
memcmp vanishes here, which means we may do some unnecessary result
generation and merging in cases where watermarks didn't change, but the
lower-level function ilk_write_wm_values already makes sure that we
don't actually try to program the watermark registers again.

v2: Squash a few commits from the original series together; no longer
    leave pre-calculated wm's in a separate temporary structure since
    it's easier to follow the logic if we just cut over to using the
    pre-calculated values directly.

v3:
 - Pass intel_crtc instead of drm_crtc to .compute_pipe_wm() entrypoint
   and use intel_atomic_get_crtc_state() to avoid need for extra
   casting.  (Ander)
 - Drop unused intel_check_crtc() function prototype.  (Ander)
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A future patch will calculate these during the atomic 'check' phase
rather than at WM programming time, so let's store the watermark
values we're planning to use in the CRTC state; the values actually
active on the hardware remains in intel_crtc.

While we're at it, do some minor restructuring to keep ILK and SKL
values in a union.

v2: Don't move cxsr_allowed to state (Maarten)

v3: Only calculate watermarks in state.  Still keep active watermarks in
    intel_crtc itself.  (Ville)
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Split ilk_update_wm() into two parts; one doing the programming
and the other the calculations.

v2: Fix typo in commit message

v3 (by Matt): Heavily rebased for current codebase.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The only platform that still has an update_sprite_wm entrypoint is SKL;
on SKL, intel_update_sprite_watermarks just updates intel_plane->wm and
then performs a regular watermark update.  However intel_plane->wm is
only used to update a couple fields in intel_wm_config, and those fields
are never used by the SKL code, so on SKL an update_sprite_wm is
effectively identical to an update_wm call.  Since we're already
ensuring that the regular intel_update_wm is called any time we'd try to
call intel_update_sprite_watermarks, the whole call is redundant and can
be dropped.
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Determine whether we need to apply this workaround at atomic check time
and just set a flag that will be used by the main watermark update
routine.

Moving this workaround into the atomic framework reduces
ilk_update_sprite_wm() to just a standard watermark update, so drop it
completely and just ensure that ilk_update_wm() is called whenever a
sprite plane is updated in a way that would affect watermarks.
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just pull the info out of the state structures rather than staging
it in an additional set of structures.  To make this more
straightforward, we change the signature of several internal WM
functions to take the crtc state as a parameter.

v2:
 - Don't forget to skip cursor planes on a loop in the DDB allocation
   function to match original behavior.  (Ander)
 - Change a use of intel_crtc->active to cstate->active.  They should
   be identical, but it's better to be consistent.  (Ander)
 - Rework more function signatures to pass states rather than crtc for
   consistency. (Ander)

v3:
  - Add missing "+ 1" to skl_wm_plane_id()'s 'overlay' case. (Maarten)
  - Packed formats should pass '0' to drm_format_plane_cpp(), not 1.
    (Maarten)
  - Drop unwanted WARN_ON() for disabled planes when calculating data
    rate for SKL.  (Maarten)
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

A bunch of SKL watermark-related structures have the cursor plane as a
separate entry from the rest of the planes.  Since a previous patch
updated I915_MAX_PLANES such that those plane arrays now have a slot for
the cursor, update the code to use the new slot in the existing plane
arrays and kill off the cursor-specific structures.

There shouldn't be any functional change here; this is just shuffling
around how the data is stored in some of the data structures.  The whole
patch is generated with Coccinelle via the following semantic patch:

        @@ struct skl_pipe_wm_parameters WMP; @@
        - WMP.cursor
        + WMP.plane[PLANE_CURSOR]

        @@ struct skl_pipe_wm_parameters *WMP; @@
        - WMP->cursor
        + WMP->plane[PLANE_CURSOR]

        @@ @@
        struct skl_pipe_wm_parameters {
        ...
        - struct intel_plane_wm_parameters cursor;
        ...
        };

        @@
        struct skl_ddb_allocation DDB;
        expression E;
        @@
        - DDB.cursor[E]
        + DDB.plane[E][PLANE_CURSOR]

        @@
        struct skl_ddb_allocation *DDB;
        expression E;
        @@
        - DDB->cursor[E]
        + DDB->plane[E][PLANE_CURSOR]

        @@ @@
        struct skl_ddb_allocation {
        ...
        - struct skl_ddb_entry cursor[I915_MAX_PIPES];
        ...
        };

        @@
        struct skl_wm_values WMV;
        expression E1, E2;
        @@
        (
        - WMV.cursor[E1][E2]
        + WMV.plane[E1][PLANE_CURSOR][E2]
        |
        - WMV.cursor_trans[E1]
        + WMV.plane_trans[E1][PLANE_CURSOR]
        )

        @@
        struct skl_wm_values *WMV;
        expression E1, E2;
        @@
        (
        - WMV->cursor[E1][E2]
        + WMV->plane[E1][PLANE_CURSOR][E2]
        |
        - WMV->cursor_trans[E1]
        + WMV->plane_trans[E1][PLANE_CURSOR]
        )

        @@ @@
        struct skl_wm_values {
        ...
        - uint32_t cursor[I915_MAX_PIPES][8];
        ...
        - uint32_t cursor_trans[I915_MAX_PIPES];
        ...
        };

        @@ struct skl_wm_level WML; @@
        (
        - WML.cursor_en
        + WML.plane_en[PLANE_CURSOR]
        |
        - WML.cursor_res_b
        + WML.plane_res_b[PLANE_CURSOR]
        |
        - WML.cursor_res_l
        + WML.plane_res_l[PLANE_CURSOR]
        )

        @@ struct skl_wm_level *WML; @@
        (
        - WML->cursor_en
        + WML->plane_en[PLANE_CURSOR]
        |
        - WML->cursor_res_b
        + WML->plane_res_b[PLANE_CURSOR]
        |
        - WML->cursor_res_l
        + WML->plane_res_l[PLANE_CURSOR]
        )

        @@ @@
        struct skl_wm_level {
        ...
        - bool cursor_en;
        ...
        - uint16_t cursor_res_b;
        - uint8_t cursor_res_l;
        ...
        };

v2: Use a PLANE_CURSOR enum entry rather than making the code reference
    I915_MAX_PLANES or I915_MAX_PLANES+1, which was confusing.  (Ander)
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Let the compiler figure out what I915_MAX_PLANES is from 'enum plane' so
that we don't need a separate #define.

While we're at it, add the cursor plane to the enum.  This will cause
I915_MAX_PLANES to now include the cursor plane in its count (it didn't
previously).   This change is safe since we currently only use this
value in array declarations (never in the actual code logic); we just
wind up allocating slightly more memory than we need to.  A followup
patch will cause various parts of the code to start using the extra
array element where appropriate.

(This patch probably should have been squashed with the followup patch,
but I couldn't figure out how to get Coccinelle to modify enum
declarations...)
Suggested-by: NAnder Conselvan De Oliveira <conselvan2@gmail.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just pull the info out of the CRTC state structure rather than staging
it in an additional structure.

Note that we use cstate->active rather than intel_crtc->active which may
appear to be a change in behavior.  However since we're no longer trying
to recalculate watermarks during the "pipe off" stage of a modeset,
intel_crtc->active and cstate->active should always be identical when
watermarks are calculated (at least for ILK-style platforms).

v2: Clarify reasoning for cstate->active and add a WARN_ON to the code
    to assert that it really is always identical to intel_crtc->active
    as expected.
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just pull the info out of the plane state structure rather than staging
it in an additional structure.

v2: Add 'visible' condition to sprites_scaled so that we don't limit the
    WM level when the sprite isn't enabled.  (Ville)
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by(v1): Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In commit

        commit e4ca0612
        Author: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
        Date:   Wed Jul 8 15:31:52 2015 +0200

            drm/i915: Don't forget to mark crtc as inactive after disable

we added extra watermark updates to all of the .crtc_disable()
entrypoints to avoid problems problems with system resume on SKL.  Those
disable entrypoints are currently called in just two places in the
driver: intel_atomic_commit (i.e., during a modeset) and
intel_crtc_disable_noatomic (which is called during hardware readout).
It seems that this extra watermark recalculation should only be
important in the latter case (which happens during a resume operation);
the former case should always have appropriate watermark programming
happening at other points in the modeset sequence.

Let's move the watermark update out of the .crtc_disable() entrypoints
and place it directly in intel_crtc_disable_noatomic() so that it only
happens on S3 resume and not during a regular modeset (since the
existing watermark handling should properly update watermarks during
normal atomic commits).

Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The RC6 residency time unit is 833.33ns on BXT according to the
specification, so update the calculation accordingly. Use the same way
as CHV/VLV to divide by the corresponding frequency, as I think this is
the more natural unit for what the HW does internally.

v2:
- add missing IS_BROXTON check (Ville)

Testcase: igt/pm_rc6_residency
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

GuC expects two bits for Render and Media domain separately when
driver sends data via host2guc SAMPLE_FORCEWAKE. Bit 0 is for
Render and bit 1 is for Media domain.

v2: Keep sync with code for WaRsDoubleRc6WrlWithCoarsePowerGating

v1: Add parameters definition to avoid magic value
Signed-off-by: NAlex Dai <yu.dai@intel.com>
Reviewed-by: NTom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Added checks for available slices, subslices and EUs for Broadwell. This
information is filled in intel_device_info and is available to user with
GET_PARAM.
Added checks for enabled slices, subslices and EU for Broadwell. This
information is based on available counts but takes power gated slices
into account. It can be read in debugfs.
Introduce new register defines that contain information on slices on
Broadwell.

v2:
- Introduce GT_SLICE_INFO register
- Change Broadwell sseu_device_status function to use GT_SLICE_INFO
  register instead of RPCS register
- Undo removal of dev_priv variables in Cherryview and Gen9
  sseu_device_satus functions

v3:
- Fix style issues

v4:
- Corrected comment
- Reverted reordering of defines

Cc: Jeff Mcgee <jeff.mcgee@intel.com>
Cc: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: NŁukasz Daniluk <lukasz.daniluk@intel.com>
Reviewed-by: NJeff McGee <jeff.mcgee@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Remove unneeded NULL test.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@ expression x; @@
-if (x != NULL)
  \(kmem_cache_destroy\|mempool_destroy\|dma_pool_destroy\)(x);
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Previously we've relied on having basically one backlight and one
backlight type per platform. This is already a bit quirky with PMIC PWM
support on VLV/CHV platforms with MIPI DSI. In the foreseeable future
we'll have at least DPCD based backlight control on eDP and DCS command
based backlight control on MIPI DSI. Backlight is becoming more and more
connector specific, so reflect this fact by making the backlight control
hooks connector specific.

This enables further work to reuse generic backlight code in
intel_panel.c while adding more specific backlight code accessed via the
hooks.

Cc: Deepak M <m.deepak@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NDeepak M <m.deepak@intel.com>
Reviewed-by: NYetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Make the alternatives stand  out better.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's more useful to limp on than bring the kernel down. Hitting this is
a more likely event with BXT DSI, although care should be taken not to
call the function for DSI.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Replace the use of mem_freq/4 with czclk_freq in the vlv c0 residency
calculations.

Also deal with VLV_COUNT_RANGE_HIGH which affects all RCx residency
counters. We have just enough bits to do this without intermediate
divisions.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>