Add self-refresh handling code for the MS7724SE board.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add self-refresh handling code for the KFR2R09 board.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add code to allow boards registering self-contained
functions for going to/from self-refresh. At this
point the board code is unused. When all supported
boards have been converted then the new sleep code
will make use of these functions.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Make use of the recently added notifier chains for sh7724
r-standby register save/restore handling. At this point
only the BSC and INTC are handled.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds atomic notifier chains for pre/post
sleep events. Useful for cpu code and boards that
need to save and restore register state before and
after entering a sleep mode.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The variable 'phys' already contains the physical address to flush. It
is not a virtual address and should not be passed to virt_to_phys().
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

num_events should be compared > MAX_HWEVENTS and not >=. The latter was
used as a debugging test which accidentally slipped in.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds in preliminary support for the SH-4A performance counters.
Presently only the first 2 counters are supported, as these are the ones
of the most interest to the perf tool and end users. Counter chaining is
not presently handled, so these are simply implemented as 32-bit
counters.

This also establishes a perf event support framework for other hardware
counters, which the existing SH-4 oprofile code will migrate over to as
the SH-4A support evolves.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

USB1 can change to host/function by checking PTB3.
This patch add USB1 gadget support and check PTB3 when boot,
and change name to usb1_common_XXX from usb1_host_XXX.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add support for cn8 and SDHI1 to the ms7724se board.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert the ms7724se board code to pass the mac
address to the sh_eth driver using platform data.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The vast majority of SH platforms want this, and the few that don't
aren't going to care one way or the other. Enable it across the board.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Presently this was tacked on to the dma debug init bits from
fs_initcall(), which is far too late for devices setting up their own
per-device coherent areas.

Throw this in the beginning of mem_init(), as per the x86 iommu
allocation.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Many of these symbols went away completely, or we just never cared about
them in the first place. Trim the exports down to the essential set.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

These were previously hidden in sh_ksyms_32, despite also being needed
for sh64 now that the cache.c code is shared.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This fixes up the dma_is_consistent() definition for the various
coherence options.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Now that this contains a grand total of 1 Kconfig option, it's hardly
worth keeping split out. Roll CONFIG_PCI back in to the top-level
architecture Kconfig, along with the other bus types.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Leaving this configurable caused more trouble than it was ever worth, so
just make it explicit. Boards that are verified one way or the other can
fix up their selects accordingly. We presently default to non-coherent
for most platforms.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Now that SH's irqflags functions are out of line it becomes necessary to
mark them as "notrace" so that we don't try to trace them.

[ Do the same for irq_64.c -- PFM. ]
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NValentin Sitdikov <valentin.sitdikov@siemens.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The hugetlb dependencies presently depend on SUPERH && MMU while the
hugetlb page size definitions depend on CPU_SH4 or CPU_SH5. This
unfortunately allows SH-3 + MMU configurations to enable hugetlbfs
without a corresponding HPAGE_SHIFT definition, resulting in the build
blowing up.

As SH-3 doesn't support variable page sizes, we tighten up the
dependenies a bit to prevent hugetlbfs from being enabled. These days
we also have a shiny new SYS_SUPPORTS_HUGETLBFS, so switch to using
that rather than adding to the list of corner cases in fs/Kconfig.
Reported-by: NKristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This was missing from the previous patch.
Reported-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert the ecovec24 board code to pass the mac
address to the sh_eth driver using platform data.
Also, remove the static clock to allow Runtime PM.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add HWBLK_ETHER to the sh_eth platform device
to allow Runtime PM of the ethernet hardware.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add an uImage.bin target to allow uncompressed uImages.
Useful for boards with busted u-boot decompression like
the rsk7203 on my desk.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fix the rsk7203 board code to build with CONFIG_MTD=n.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This unbreaks kexec support. Without this fix all
cases of kexec fails since __pa() does not behave
like PHYSADDR(). The downside is that we also kill
the code blocking users running old kexec-tools.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add SD Card support to the kfr2r09 board using the
sh_mobile_sdhi driver hooked up to SDHI0 and yc304.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add SD Card support to the se7724 board using the
sh_mobile_sdhi driver hooked up to SDHI0 and CN7.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert the AP325 board to use sh_mobile_sdhi for the
SD Card connected to CN3 instead of mmc_spi.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Convert the Migo-R board to use sh_mobile_sdhi for the
SD Card connected to CN9 instead of mmc_spi.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

When CONFIG_FUNCTION_GRAPH_TRACER is enabled the function graph tracer
may patch return addresses on the stack with the address of
return_to_handler(). This really confuses the DWARF unwinder because it
will try find the caller of return_to_handler(), not the caller of the
real return address.

So teach the DWARF unwinder how to find the real return address whenever
it encounters return_to_handler().

This patch does not cope very well when multiple return addresses on the
stack have been patched. To make it work properly it would require state
to track how many return_to_handler()'s have been seen so that we'd know
where to look in current->curr_ret_stack[]. So for now, instead of
trying to handle this, just moan if more than one return address on the
stack has been patched.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

ERROR: "__movmemSI12" [net/unix/unix.ko] undefined!
ERROR: "__movmemSI52" [net/ipv6/sit.ko] undefined!
ERROR: "__movmemSI24" [net/ipv6/ipv6.ko] undefined!
ERROR: "__movmemSI60" [net/ipv6/ipv6.ko] undefined!
ERROR: "__movmemSI16" [net/ipv6/ipv6.ko] undefined!
ERROR: "__movmemSI20" [net/ipv6/ipv6.ko] undefined!
ERROR: "__movmemSI32" [net/ipv6/ipv6.ko] undefined!
Signed-off-by: NLubomir Rintel <lkundrak@v3.sk>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds an __irq_entry annotation for do_IRQ() so that the IRQ
annotation in the function graph tracer works as advertized. We already
have the IRQENTRY section wired up, so this is just a trivial addition
to actually make use of it.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This moves the current dma_alloc/free_coherent() calls to a generic
variant and plugs them in for the nommu default. Other variants can
override the defaults in the dma mapping ops directly.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

When renaming kernel_fpu_using to irq_fpu_usable, the semantics of the
function is changed too, from mesuring whether kernel is using FPU,
that is, the FPU is NOT available, to measuring whether FPU is usable,
that is, the FPU is available.

But the usage of irq_fpu_usable in aesni-intel_glue.c is not changed
accordingly. This patch fixes this.
Signed-off-by: NHuang Ying <ying.huang@intel.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This converts the old DMA mapping support to the new generic
dma-mapping-common.h abstraction.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fixes up flush_dcache_page() references by modules with run-time cache
disabling.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>