Luxul XWR-1200 in a dual-band router based on BCM47081. It uses serial
flash (for bootloader and NVRAM) and NAND flash (for firmware).
Signed-off-by: NDan Haab <dhaab@luxul.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Luxul XAP-1410 in a dual-band access point device based on BCM47081 with
serial flash. It has 3 LEDs and just one (reset) button.
Signed-off-by: NDan Haab <dhaab@luxul.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Netgear R8000 is a tri-band home router. It has three BCM43602 chipsets
two of them for 5 GHz band. Both seem the same and their firmwares
report the same set of channels. The problem is due to hardware / board
design there are extra limitations that should be respected.

First PHY should be used for U-NII-2 and U-NII-3. Third PHY should be
used for U-NII-1. Using them in a different way may result in wireless
not working or in noticeably reduced performance. Basic version of this
info was provided by Broadcom employee, then it has been verified by me
using original vendor firmware (which has limitations hardcoded in UI).

This patch uses recently introduced ieee80211-freq-limit property to
describe these limitations at DT level.

Referencing PCIe devices in DT required specifying all related bridges.
Below you can see (a bit complex) PCI tree from R8000 that explains all
entries that I needed to put in DT.

0000:00:00.0		14e4:8012	Bridge Device
└─ 0000:01:00.0		14e4:aa52	Network Controller

0001:00:00.0		14e4:8012	Bridge Device
└─ 0001:01:00.0		10b5:8603	Bridge Device
   ├─ 0001:02:01.0	10b5:8603	Bridge Device
   │  └─ 0001:03:00.0	14e4:aa52	Network Controller
   ├─ 0001:02:02.0	10b5:8603	Bridge Device
   │  └─ 0001:04:00.0	14e4:aa52	Network Controller
   ├─ 0001:02:03.0	000d:0000	0x000000
   ├─ 0001:02:04.0	000d:0000	0x000000
   ├─ 0001:02:05.0	000d:0000	0x000000
   ├─ 0001:02:06.0	000d:0000	0x000000
   ├─ (...)
   ├─ 0001:02:1d.0	000d:0000	0x000000
   ├─ 0001:02:1e.0	000d:0000	0x000000
   └─ 0001:02:1f.0	000d:0000	0x000000
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add SD/MMC support to the Broadcom NSP SVK and XMC.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Enable the ethernet in the NSP XMC (bcm958525xmc) device tree
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add and enable the third AMAC ethernet interface in the device trees for
the platforms where it is present.  Also, enable amac1 on some of the
platforms where that was missing.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add the layout of the switch ports found on the BCM958625K reference
board. The CPU port is hooked up to the AMAC0 Ethernet controller
adapter.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

QSPI device tree entries are present in bcm958625k, but missing from
bcm958522er, bcm958525er, bcm958525xmc, bcm958622hr, bcm958623hr,
bcm958625hr, and bcm988312hr.  Duplicate the entry in bcm958625k for
all of those that are missing it (as they are identical).
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

The NAND partition unit address does not match the other NSP device tree
files.  This change makes them uniform.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

The QSPI entry was added out of the sequental order that the rest of the
DTSI file is in.  Move it to make it fit in properly.  Also, some other
entries have been added in a non-alphabetical order in the DTS files,
making them different from the other NSP DTS files.  Move the relevant
peices to make it match.  Finally, remove errant new lines.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Broadcom OHCI and EHCI controllers always have 2 ports each on the root
hub. Describe them in DT to allow specifying extra info or referencing
port nodes.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

The first 128 MiB of RAM can be accessed using an alias at address 0x0.

In theory we could access whole RAM using 0x80000000 - 0xbfffffff range
(up to 1 GiB) but it doesn't seem to work on Northstar. For some reason
(hardware setup left by the bootloader maybe?) 0x80000000 - 0x87ffffff
range can't be used. I reproduced this problem on:
1) Buffalo WZR-600DHP2 (BCM47081)
2) Netgear R6250 (BCM4708)
3) D-Link DIR-885L (BCM47094)

So it seems we're forced to access first 128 MiB using alias at 0x0 and
the rest using real base address + 128 MiB offset which is 0x88000000.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Acked-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

There is one GPIO controlling power for both USB ports.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

There are 3 separated controllers, one per USB /standard/. With PHY
drivers in place they can be simply supported with generic drivers.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Reviewed-by: NRay Jui <ray.jui@broadcom.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

They were named incorrectly most likely due to copy & paste mistake.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Every device tested so far got UART0 (at 0x18000300) working as serial
console. It's most likely part of reference design and all vendors use
it that way.

It seems to be easier to enable it by default and just disable it if we
ever see a device with different hardware design.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Acked-by: NJon Mason <jon.mason@broadcom.com>
Acked-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

I am getting the following warning when I build kernel 4.9-git on my
PowerBook G4 with a 32-bit PPC processor:

    AS      arch/powerpc/kernel/misc_32.o
  arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef]

This problem is evident after commit 989cea5c ("kbuild: prevent
lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an
error that has been in the code since 2005 when this source file was
created.  That was with commit 9994a338 ("powerpc: Introduce
entry_{32,64}.S, misc_{32,64}.S, systbl.S").

The offending line does not make a lot of sense.  This error does not
seem to cause any errors in the executable, thus I am not recommending
that it be applied to any stable versions.

Thanks to Nicholas Piggin for suggesting this solution.

Fixes: 9994a338 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S")
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The timer type simplifications caused a new gcc warning:

  drivers/base/power/domain.c: In function ‘genpd_runtime_suspend’:
  drivers/base/power/domain.c:562:14: warning: ‘time_start’ may be used uninitialized in this function [-Wmaybe-uninitialized]
     elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));

despite the actual use of "time_start" not having changed in any way.
It appears that simply changing the type of ktime_t from a union to a
plain scalar type made gcc check the use.

The variable wasn't actually used uninitialized, but gcc apparently
failed to notice that the conditional around the use was exactly the
same as the conditional around the initialization of that variable.

Add an unnecessary initialization just to shut up the compiler.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull timer type cleanups from Thomas Gleixner:
 "This series does a tree wide cleanup of types related to
  timers/timekeeping.

   - Get rid of cycles_t and use a plain u64. The type is not really
     helpful and caused more confusion than clarity

   - Get rid of the ktime union. The union has become useless as we use
     the scalar nanoseconds storage unconditionally now. The 32bit
     timespec alike storage got removed due to the Y2038 limitations
     some time ago.

     That leaves the odd union access around for no reason. Clean it up.

  Both changes have been done with coccinelle and a small amount of
  manual mopping up"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  ktime: Get rid of ktime_equal()
  ktime: Cleanup ktime_set() usage
  ktime: Get rid of the union
  clocksource: Use a plain u64 instead of cycle_t

Pull SMP hotplug notifier removal from Thomas Gleixner:
 "This is the final cleanup of the hotplug notifier infrastructure. The
  series has been reintgrated in the last two days because there came a
  new driver using the old infrastructure via the SCSI tree.

  Summary:

   - convert the last leftover drivers utilizing notifiers

   - fixup for a completely broken hotplug user

   - prevent setup of already used states

   - removal of the notifiers

   - treewide cleanup of hotplug state names

   - consolidation of state space

  There is a sphinx based documentation pending, but that needs review
  from the documentation folks"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/armada-xp: Consolidate hotplug state space
  irqchip/gic: Consolidate hotplug state space
  coresight/etm3/4x: Consolidate hotplug state space
  cpu/hotplug: Cleanup state names
  cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
  staging/lustre/libcfs: Convert to hotplug state machine
  scsi/bnx2i: Convert to hotplug state machine
  scsi/bnx2fc: Convert to hotplug state machine
  cpu/hotplug: Prevent overwriting of callbacks
  x86/msr: Remove bogus cleanup from the error path
  bus: arm-ccn: Prevent hotplug callback leak
  perf/x86/intel/cstate: Prevent hotplug callback leak
  ARM/imx/mmcd: Fix broken cpu hotplug handling
  scsi: qedi: Convert to hotplug state machine

Pull turbostat updates from Len Brown.

* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: remove obsolete -M, -m, -C, -c options
  tools/power turbostat: Make extensible via the --add parameter
  tools/power turbostat: Denverton uses a 25 MHz crystal, not 19.2 MHz
  tools/power turbostat: line up headers when -M is used
  tools/power turbostat: fix SKX PKG_CSTATE_LIMIT decoding
  tools/power turbostat: Support Knights Mill (KNM)
  tools/power turbostat: Display HWP OOB status
  tools/power turbostat: fix Denverton BCLK
  tools/power turbostat: use intel-family.h model strings
  tools/power/turbostat: Add Denverton RAPL support
  tools/power/turbostat: Add Denverton support
  tools/power/turbostat: split core MSR support into status + limit
  tools/power turbostat: fix error case overflow read of slm_freq_table[]
  tools/power turbostat: Allocate correct amount of fd and irq entries
  tools/power turbostat: switch to tab delimited output
  tools/power turbostat: Gracefully handle ACPI S3
  tools/power turbostat: tidy up output on Joule counter overflow

Add a new page flag, PageWaiters, to indicate the page waitqueue has
tasks waiting. This can be tested rather than testing waitqueue_active
which requires another cacheline load.

This bit is always set when the page has tasks on page_waitqueue(page),
and is set and cleared under the waitqueue lock. It may be set when
there are no tasks on the waitqueue, which will cause a harmless extra
wakeup check that will clears the bit.

The generic bit-waitqueue infrastructure is no longer used for pages.
Instead, waitqueues are used directly with a custom key type. The
generic code was not flexible enough to have PageWaiters manipulation
under the waitqueue lock (which simplifies concurrency).

This improves the performance of page lock intensive microbenchmarks by
2-3%.

Putting two bits in the same word opens the opportunity to remove the
memory barrier between clearing the lock bit and testing the waiters
bit, after some work on the arch primitives (e.g., ensuring memory
operand widths match and cover both bits).
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A page is not added to the swap cache without being swap backed,
so PageSwapBacked mappings can use PG_owner_priv_1 for PageSwapCache.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Acked-by: NHugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

No point in going through loops and hoops instead of just comparing the
values.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>

ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>

ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.

Get rid of the union and just keep ktime_t as simple typedef of type s64.

The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>

There is no point in having an extra type for extra confusion. u64 is
unambiguous.

Conversion was done with the following coccinelle script:

@rem@
@@
-typedef u64 cycle_t;

@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>

The mpic is either the main interrupt controller or is cascaded behind a
GIC. The mpic is single instance and the modes are mutually exclusive, so
there is no reason to have seperate cpu hotplug states.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/20161221192112.333161745@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Even if both drivers are compiled in only one instance can run on a given
system depending on the available GIC version.

So having seperate hotplug states for them is pointless.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.252416267@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Even if both drivers are compiled in only one instance can run on a given
system depending on the available tracer cell.

So having seperate hotplug states for them is pointless.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: http://lkml.kernel.org/r/20161221192112.162765484@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.

Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

hotcpu_notifier(), cpu_notifier(), __hotcpu_notifier(), __cpu_notifier(),
register_hotcpu_notifier(), register_cpu_notifier(),
__register_hotcpu_notifier(), __register_cpu_notifier(),
unregister_hotcpu_notifier(), unregister_cpu_notifier(),
__unregister_hotcpu_notifier(), __unregister_cpu_notifier()

are unused now. Remove them and all related code.

Remove also the now pointless cpu notifier error injection mechanism. The
states can be executed step by step and error rollback is the same as cpu
down, so any state transition can be tested w/o requiring the notifier
error injection.

Some CPU hotplug states are kept as they are (ab)used for hotplug state
tracking.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20161221192112.005642358@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Install the callbacks via the state machine. No functional change.
Signed-off-by: NAnna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: devel@driverdev.osuosl.org
Cc: Andreas Dilger <andreas.dilger@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: rt@linutronix.de
Cc: lustre-devel@lists.lustre.org
Link: http://lkml.kernel.org/r/20161202110027.htzzeervzkoc4muv@linutronix.de
Link: http://lkml.kernel.org/r/20161221192111.922872524@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Install the callbacks via the state machine. No functional change.

This is the minimal fixup so we can remove the hotplug notifier mess
completely.

The real rework of this driver to use work queues is still stuck in
review/testing on the SCSI mailing list.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20161221192111.836895753@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Install the callbacks via the state machine. No functional change.

This is the minimal fixup so we can remove the hotplug notifier mess
completely.

The real rework of this driver to use work queues is still stuck in
review/testing on the SCSI mailing list.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20161221192111.757309869@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Developers manage to overwrite states blindly without thought. That's fatal
and hard to debug. Add sanity checks to make it fail.

This requries to restructure the code so that the dynamic state allocation
happens in the same lock protected section as the actual store. Otherwise
the previous assignment of 'Reserved' to the name field would trigger the
overwrite check.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192111.675234535@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

The error cleanup which is invoked when the hotplug state setup failed
tries to remove the failed state, which is broken.

Fixes: 8fba38c9 ("x86/msr: Convert to hotplug state machine")
Reported-by: Nkernel test robot <fengguang.wu@intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Siewior <bigeasy@linutronix.de>

In case the driver registration fails, the hotplug callback is leaked.

Not fatal, because it's never invoked as there are no instances registered,
but wrong nevertheless.

Fixes: fdc15a36 ("bus/arm-ccn: Convert to hotplug statemachine")
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>

If the pmu registration fails the registered hotplug callbacks are not
removed. Wrong in any case, but fatal in case of a modular driver.

Replace the nonsensical state names with proper ones while at it.

Fixes: 77c34ef1 ("perf/x86/intel/cstate: Convert Intel CSTATE to hotplug state machine")
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org