This propagates through all the drivers and mac80211.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

mac80211 takes care of all the needed steps for hwsim, so indicate
support for this capability.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This will allow the low level driver to make decision based
on the vif such as queues etc...
Since the vif might be NULL, we can't add it to the tracing
functions.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix staging rtl8821ae driver]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Commit 2b3d7b75("qlcnic: Add VXLAN Rx offload support") uses
vxlan_get_rx_port() which caused build failure when VXLAN=m.

This patch fixes the build failure by adding dependency on VXLAN
in Kconfig of qlcnic module and use vxlan_get_rx_port() and support
code accordingly.
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit fixes a build error reported by Fengguang, that is
triggered when CONFIG_NETWORK_PHY_TIMESTAMPING is not set:

  ERROR: "ptp_classify_raw" [drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe.ko] undefined!

The fix is to introduce its own file for the PTP BPF classifier,
so that PTP_1588_CLOCK and/or NETWORK_PHY_TIMESTAMPING can select
it independently from each other. IXP4xx driver on ARM needs to
select it as well since it does not seem to select PTP_1588_CLOCK
or similar that would pull it in automatically.

This also allows for hiding all of the internals of the BPF PTP
program inside that file, and only exporting relevant API bits
to drivers.

This patch also adds a kdoc documentation of ptp_classify_raw()
API to make it clear that it can return PTP_CLASS_* defines. Also,
the BPF program has been translated into bpf_asm code, so that it
can be more easily read and altered (extensively documented in [1]).

In the kernel tree under tools/net/ we have bpf_asm and bpf_dbg
tools, so the commented program can simply be translated via
`./bpf_asm -c prog` where prog is a file that contains the
commented code. This makes it easily readable/verifiable and when
there's a need to change something, jump offsets etc do not need
to be replaced manually which can be very error prone. Instead,
a newly translated version via bpf_asm can simply replace the old
code. I have checked opcode diffs before/after and it's the very
same filter.

  [1] Documentation/networking/filter.txt

Fixes: 164d8c66 ("net: ptp: do not reimplement PTP/BPF classifier")
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jiri Benc <jbenc@redhat.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "core_ops" variable isn't referenced outside this file and Sparse
complains about it:

	drivers/net/ethernet/samsung/sxgbe/sxgbe_core.c:239:29: warning:
	symbol 'core_ops' was not declared. Should it be static?
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bitwise '|' was intended here instead of logical '||'.

Fixes: 1edb9ca6 ('net: sxgbe: add basic framework for Samsung 10Gb ethernet driver')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"err" is always zero at this point so we always unregister and free the
mdio_bus before returning success.  This seems like left over code and
I have deleted it.

Fixes: 1edb9ca6 ('net: sxgbe: add basic framework for Samsung 10Gb ethernet driver')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using the "separate_tx_channels=1" module parameter, the TX queues are
initially numbered starting from the first TX-only channel number (after all the
RX-only channels).  efx_set_channels() renumbers the queues so that they are
indexed from zero.

On EF10, the TX queues need to be relabelled in this way before calling the
dimension_resources NIC type operation, otherwise the TX queue PIO buffers can be
linked to the wrong VIs when using "separate_tx_channels=1".

Added comments to explain UC/WC mappings for PIO buffers
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When netback discovers frontend is sending malformed packet it will
disables the interface which serves that frontend.

However disabling a network interface involving taking a mutex which
cannot be done in softirq context, so we need to defer this process to
kthread context.

This patch does the following:
1. introduce a flag to indicate the interface is disabled.
2. check that flag in TX path, don't do any work if it's true.
3. check that flag in RX path, turn off that interface if it's true.

The reason to disable it in RX path is because RX uses kthread. After
this change the behavior of netback is still consistent -- it won't do
any TX work for a rogue frontend, and the interface will be eventually
turned off.

Also change a "continue" to "break" after xenvif_fatal_tx_err, as it
doesn't make sense to continue processing packets if frontend is rogue.

This is a fix for XSA-90.
Reported-by: NTörök Edwin <edwin@etorok.net>
Signed-off-by: NWei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure that vxlan_get_rx_port() is present in the kernel build in a manner
consistent with mlx4, else mlx4 can be made built-in where vxlan a module and
the phase of the build linking fails. Add CONFIG_MLX4_EN_VXLAN for that.

Also, #ifdef the advertizement and implementation of the mlx4 vxlan ndo
calls and related code under this config directive.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a CONFIG_BE2NET_VXLAN define to control be2net's build
dependency on the VXLAN driver.

Without this fix, the kernel build fails when VxLAN driver is
selected to be built as a module while be2net is built-in.

fixes: c9c47142 ("be2net: csum, tso and rss steering offload support for VxLAN")
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no point to toggle the RX led for every packet. Especially if
we have a full FIFO we want to avoid everything we can.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The function loads the message object from the hardware to get the
payload length. The previous patch stores that information in an
array, so we can avoid the hardware access.

Remove the hardware access and move the led toggle outside of the
spinlocked region. Toggle the led only once when at least one packet
has been received.

Binary size shrinks along with the code
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

We can avoid the HW access in TX cleanup path for retrieving the DLC
of the sent package if we store the DLC in a private array.

Ideally this should be handled in the can_echo_skb functions, but I
leave that exercise to the CAN folks.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

commit 4ce78a83 (can: c_can: Speed up rx_poll function) hyped a
performance improvement by reducing the access to the interrupt
pending register from a dual 16 bit to a single 16 bit access. Wow!

Thereby it crippled the driver to cast the 16 msg objects in stone,
which is completly braindead as contemporary hardware has up to 128
message objects. Supporting larger object buffers is a major surgery,
but it'd be definitely worth it especially as the driver does not
support HW message filtering ....

The logic of the "FIFO" implementation is to split the FIFO in half.

For the lower half we read the buffers and clear the interrupt pending
bit, but keep the newdat bit set, so the HW will queue above those
buffers.

When we read out the last low buffer then we reenable all the low half
buffers by clearing the newdat bit.

The upper half buffers clear the newdat and the interrupt pending bit
right away as we know that the lower half bits are clear and give us a
headstart against the hardware.

Now the implementation is:

    transfer_message_object()
    read_object_and_put_into_skb();

    if (obj < END_OF_LOW_BUF)
       clear_intpending(obj)
    else if (obj > END_OF_LOW_BUF)
       clear_intpending_and_newdat(obj)
    else if (obj == END_OF_LOW_BUF)
       clear_newdat_of_all_low_objects()

The hardware allows to avoid most of the mess simply because we can
tell the transfer_message_object() function to clear bits right away.

So we can be clever and do:

   if (obj <= END_OF_LOW_BUF)
      ctrl = TRANSFER_MSG | CLEAR_INTPND;
   else
      ctrl = TRANSFER_MSG | CLEAR_INTPND | CLEAR_NEWDAT;

    transfer_message_object(ctrl)
    read_object_and_put_into_skb();

    if (obj == END_OF_LOW_BUF)
       clear_newdat_of_all_low_objects()

So we save a complete control operation on all message objects except
the one which is the end of the low buffer. That's a few micro seconds
per object.

I'm not adding a boasting profile to that, simply because it's self
explaining.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
[mkl: adjusted subject and commit message]
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

If every other line contains line breaks, that's a clear sign for
indentation level madness. Split out the inner loop and move the code
to a separate function. gcc creates slightly worse code for that, but
we'll fix that in the next step.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
[mkl: adjusted subject]
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The network core does not serialize the access to the hardware. The
xmit related code lets the following happen:

CPU0 	     	       CPU1
interrupt()
 do_poll()
   c_can_do_tx()
    Fiddle with HW and	xmit()
    internal data	  Fiddle with HW and
    	     		  internal data

due the complete lack of serialization.

Add proper locking.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The rx_poll code has the following gem:

	if (msg_ctrl_save & IF_MCONT_EOB)
		return num_rx_pkts;

The EOB bit is the indicator for the hardware that this is the last
configured FIFO object. But this object can contain valid data, if we
manage to free up objects before the overrun case hits.

Now if the code exits due to the EOB bit set, then this buffer is
stale and the interrupt bit and NewDat bit of the buffer are still
set. Results in a nice interrupt storm unless we come into an overrun
situation where the MSGLST bit gets set.

     ksoftirqd/0-3     [000] ..s.    79.124101: c_can_poll: rx_poll: val: 00008001 pend 00008001
     ksoftirqd/0-3     [000] ..s.    79.124176: c_can_poll: rx_poll: val: 00008000 pend 00008000
     ksoftirqd/0-3     [000] ..s.    79.124187: c_can_poll: rx_poll: val: 00008002 pend 00008002
     ksoftirqd/0-3     [000] ..s.    79.124256: c_can_poll: rx_poll: val: 00008000 pend 00008000
     ksoftirqd/0-3     [000] ..s.    79.124267: c_can_poll: rx_poll: val: 00008000 pend 00008000

The amazing thing is that the check of the MSGLST (aka overrun bit)
used to be after the check of the EOB bit. That was "fixed" in commit
5d0f801a(can: c_can: Fix RX message handling, handle lost message
before EOB). But the author of this "fix" did not even understand that
the EOB check is broken as well.

Again a simple solution: Remove
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
[mkl: adjusted subject and commit message]
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The lost message handling is broken in several ways.

1) Clearing the message lost flag is done by writing 0 to the
   message control register of the object.

   #define IF_MCONT_CLR_MSGLST    (0 << 14)

   That clears the object buffer configuration in the worst case,
   which results in a loss of the EOB flag. That leaves the FIFO chain
   without a limit and causes a complete lockup of the HW

2) In case that the error skb allocation fails, the code happily
   claims that it handed down a packet. Just an accounting bug, but ....

3) The code adds a lot of pointless overhead to that error case, where
   we need to get stuff done as fast as possible to avoid more packet
   loss.

   - printk an annoying error message
   - reread the object buffer for nothing

Fix is simple again:

  - Use the already known MSGCTRL content and only clear the MSGLST bit
  - Fix the buffer accounting by adding a proper return code
  - Remove the pointless operations
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The buffer handling of c_can has been broken forever. That leads to
message reordering:

ksoftirqd/0-3     [000] ..s.    79.123776: c_can_poll: rx_poll: val: 00007fff
ksoftirqd/0-3     [000] ..s.    79.124101: c_can_poll: rx_poll: val: 00008001

What happens is:

CPU				HW
				queue new packet into obj 16 (0-15 are busy)
read obj 1-15
return because pending is 0
				set pending obj 16 -> pending reg 8000
				queue new packet into obj 1
				set pending obj 1 -> pending reg 8001

So the current algorithmus reads the newest message first, which
violates the ordering rules of CAN.

Add proper handling of that situation by analyzing the contents of the
pending register for gaps.

This does NOT fix the message object corruption which can lead to
interrupt storms. Thats addressed in the next patches.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
[mkl: adjusted subject]
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The hardware has two message control interfaces, but the code only uses the
first one. So on SMP the following can be observed:

CPU0 	       	CPU1
rx_poll()
  write IF1	xmit()
		write IF1
  write IF1

That results in corrupted message object configurations. The TX/RX is not
globally serialized it's only serialized on a core.

Simple solution: Let RX use IF1 and TX use IF2 and all is good.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The function is broken in several ways:

    - The function does not wait for the init to complete.
      That can take quite some microseconds.

    - No protection against being called for two chips at the same
      time. SMP is such a new thing, right?

Clear the start and the init done bit unconditionally and wait for both bits to
be clear.

In the enable path set the init bit and wait for the init done bit.

Add proper locking.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

According to the documentation the CPU must wait for CONTROL_INIT to
be cleared before writing to the baudrate registers.
Signed-off-by: NBenedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds return value checking to all direct and indirect users of
c_can_set_bittiming().
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds the missing netif_napi_del() to the free_c_can_dev() function.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Fixed a memory leak when an error occurred in the transmit function. In the
error handling the urb wasn't freed before returning. There was also a call to
the usb_unanchor_urb() function but the urb wasn't anchored.
Signed-off-by: NBjorn Van Tilt <bjorn.vantilt@gmail.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Resolve some rcu warnings produced when LER actions take place.
This appears to be due to not holding the rtnl lock when calling
ixgbe_down, so hold the lock. Also avoid disabling the device
when it is already disabled. This check is necessary because the
callback can be called more than once in some cases.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Resolve some rcu warnings produced when LER actions take place.
This appears to be due to not holding the rtnl lock when calling
ixgbe_down, so hold the lock. Also avoid disabling the device
when it is already disabled. This check is necessary because the
callback can be called more than once in some cases.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use pci_iounmap instead of iounmap when the virtual mapping was done
with pci_iomap. A simplified version of the semantic patch that finds this
issue is as follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r@
expression addr;
@@
addr = pci_iomap(...)

@rr@
expression r.addr;
@@
* iounmap(addr)
// </smpl>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Casting a pointer to a pointer of the same type is pointless,
so remove these unnecessary casts.

Done via coccinelle script:

$ cat typecast_2.cocci
@@
type T;
T *foo;
@@

-	(T *)foo
+	foo
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Using addressof then casting to the original type is pointless,
so remove these unnecessary casts.

Done via coccinelle script:

$ cat typecast.cocci
@@
type T;
T foo;
@@

-	(T *)&foo
+	&foo
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The commit 6494294f ("i40e/i40evf: Use
dma_set_mask_and_coherent") uses dma_set_mask_and_coherent() to
replace dma_set_coherent_mask() for the benefit of return error.
The conversion brings some confusion in error checking as whether
against DMA_BIT_MASK(64) or DMA_BIT_MASK(32). For one, if error is
zero, the check will be against DMA_BIT_MASK(64) twice. Fix this
error checking by binding the check to the pertinent one.

Cc: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The commit c7d05ca8 ("i40e: driver ethtool core") introduced the
new function i40e_add_del_fdir_sctpv4() with the kernel doc
description a little bit off. The trivial error was copied over to a
different file by the commit 17a73f6b ("i40e: Flow Director
sideband accounting") most recently. Fix the kernel doc with the
correct description for clarity.

Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change the ixgbe_read_reg function name to ixgbevf_read_reg to
avoid a namespace clash with the ixgbe driver. This will allow
ixgbe to take its register read function out-of-line to reduce
memory footprint.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The commit c97506ab ("ixgbe: Add check for FW veto bit")
introduced the new function ixgbe_check_reset_blocked() with a minor
issue in declaration. Fix the declaration by changing the type
specifier to bool as the definition returns a boolean value.
Additionally all ixgbe_check_reset_blocked() callers are expected to
return a boolean value.
Signed-off-by: NJean Sacren <sakiwit@gmail.com>
Acked-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe has a single set of TX time stamping resources per NIC.
Use a simple bit lock to avoid race conditions and leaking skbs
when multiple TX rings try to claim time stamping.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

skb_tx_timestamp() does not report software time stamp
if SKBTX_IN_PROGRESS is set. According to timestamping.txt
software time stamps are a fallback and should not be
generated if hardware time stamp is provided.

Move call to skb_tx_timestamp() after setting
SKBTX_IN_PROGRESS.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ptp_tx_skb is always set before work is scheduled,
work is cancelled before ptp_tx_skb is set to NULL.
PTP work cannot ever see ptp_tx_skb set to NULL.
Signed-off-by: NJakub Kicinski <kubakici@wp.pl>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In commit da1e2046, the flow for enabling/disabling an Si errata
workaround (e1000_lv_jumbo_workaround_ich8lan) was changed to fix a problem
with iAMT connections dropping on interface down with jumbo frames set.
Part of this change was to move the function call disabling the workaround
to e1000e_down() from the e1000_setup_rctl() function.  The mechanic for
disabling of this workaround involves writing several MAC and PHY registers
back to hardware defaults.

After this commit, when the driver is loaded with the cable out, the PHY
registers are not programmed with the correct default values.  This causes
the device to be capable of transmitting packets, but is unable to recieve
them until this workaround is called.

The flow of e1000e's open code relies upon calling the above workaround to
expicitly program these registers either with jumbo frame appropriate settings
or h/w defaults on 82579 and newer hardware.

Fix this issue by adding logic to e1000_setup_rctl() that not only calls
e1000_lv_jumbo_workaround_ich8lan() when jumbo frames are set, to enable the
workaround, but also calls this function to explicitly disable the workaround
in the case that jumbo frames are not set.
Signed-off-by: NDave Ertman <davidx.m.ertman@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>