ARCH_PNX010X doesn't exist in Kconfig, therefore removing all
references for it from the source code/Kconfig.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Body of the explanation:
   -support 16bit and 32bit bus width.
   -add device reset for ks8842/8841 Micrel device.
   -set 100Mbps as a default for Micrel device.
   -set MAC address in both MAC/Switch layer with different sequence for Micrel
    device, as mentioned in data sheet.
   -use private data to set options both 16/32bit bus width and Micrel device/
    Timberdale(FPGA).
   -update Kconfig in order to put more information about ks8842 device.
Signed-off-by: NDavid J. Choi <david.choi@micrel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SH7757 has 2 Fast Ethernet controller (ETHER) and 2 Gigabit Ethernet
Controller (GETHER). This patch supports 2 ETHER only.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stitch new T4 PCI-E SR-IOV Virtual Function driver into the build.

Signed-off-by: Casey Leedom
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

enic now uses the GRO mechanism instead of LRO to pass skbs to upper
layers.
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netxen_nic and qlcnic driver depends on firmware_class module.
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for using phylib and adds the required mdiobus driver
stubs. This allows for less code to be present in the driver and removes
the PHY status specific timer which is now handled by phylib directly.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Newer on-chip MAC peripherals support IEEE 1588 PTP in the hardware, so
extend the driver to support this functionality.
Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All distributions enable it, therefore no significant body of users
are even testing the driver with it disabled.  And making NAPI
configurable is heavily discouraged anyways.

I left the MSI-X interrupt enabling thing in an "#if 0" block
so hopefully someone can debug that and it can get re-enabled.
Probably it was just one of the NVIDIA chipset MSI erratas that
we work handle these days in the PCI quirks (see drivers/pci/quirks.c
and stuff like nvenet_msi_disable()).
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for using the LL TEMAC Ethernet driver on
non-Virtex 5 platforms by adding support for accessing the Soft DMA
registers as if they were memory mapped instead of solely through the
DCR's (available on the Virtex 5).

The patch also updates the driver so that it runs on the MicroBlaze.
The changes were tested on the PowerPC 440, PowerPC 405, and the
MicroBlaze platforms.
Signed-off-by: NJohn Tyner <jtyner@cs.ucr.edu>
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 45956914.

Uses virt_to_bus() and breaks the build.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows the au1000-eth driver to be compiled as a module.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for using the LL TEMAC Ethernet driver on
non-Virtex 5 platforms by adding support for accessing the Soft DMA
registers as if they were memory mapped instead of solely through the
DCR's (available on the Virtex 5).

The patch also updates the driver so that it runs on the MicroBlaze.
The changes were tested on the PowerPC 440, PowerPC 405, and the
MicroBlaze platforms.
Signed-off-by: NJohn Tyner <jtyner@cs.ucr.edu>
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch splits the pppol2tp driver into separate L2TP and PPP parts
to prepare for L2TPv3 support. In L2TPv3, protocols other than PPP can
be carried, so this split creates a common L2TP core that will handle
the common L2TP bits which protocol support modules such as PPP will
use.

Note that the existing pppol2tp module is split into l2tp_core and
l2tp_ppp by this change.

There are no feature changes here. Internally, however, there are
significant changes, mostly to handle the separation of PPP-specific
data from the L2TP session and to provide hooks in the core for
modules like PPP to access.
Signed-off-by: NJames Chapman <jchapman@katalix.com>
Reviewed-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BugLink: http://bugs.launchpad.net/bugs/457878

v2:
 - remove duplicated phy_speed caculation
 - fix the phy_speed caculation according to the DataSheet

v1:
 - removed old MII phy control code
 - add phylib supporting
 - add ethtool interface to make user space NetworkManager works

Tested on Freescale i.MX51 Babbage board.

This patch is based on a patch from Frederic Rodo <fred.rodo@gmail.com>

Cc: Frederic Rodo <fred.rodo@gmail.com>
Signed-off-by: NBryan Wu <bryan.wu@canonical.com>
Acked-by: NAmit Kucheria <amit.kucheria@canonical.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDimitris Michailidis <dm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add CAIF Serial driver. This driver is implemented as a line discipline.

caif_serial uses the following module parameters:
ser_use_stx - specifies if STart of frame eXtension is in use.
ser_loop    - sets the interface in loopback mode.
Signed-off-by: NSjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nowadays, most distributions enable netconsole by default,
including RHEL, Fedora, Debian, Arch, Opensuse. And
we don't have any bug reports about it. So I think there
is no need to mark it as experimental any more.

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NWANG Cong <amwang@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) Change enic driver description to "Cisco VIC Ethernet NIC Driver"
2) Fix tab space
3) Update MAINTAINERS list
Signed-off-by: NScott Feldman <scofeldm@cisco.com>
Signed-off-by: NVasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: NRoopa Prabhu <roprabhu@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some embedded ColdFire based boards use the SMC 91x family of ethernet
devices. (For example the Freescale M5249C3 and MoretonBay NETtel).

Add IO access support to the SMC91x driver, and allow this driver to
be configured for ColdFire platforms.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported by Stephen Rothwell.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds device driver for Aeroflex Gaisler 10/100 and 10/100/1G Ethernet
MAC IP cores.
Signed-off-by: NKristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code has been around for a long time now and is known to work on a
bunch of different parts/boards.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These changes add MDIO and phy lib support to the driver as the
IP core now supports the MDIO bus.

The MDIO bus and phy are added as a child to the emaclite in the device
tree as illustrated below.

mdio {
	#address-cells = <1>;
	#size-cells = <0>;
	phy0: phy@7 {
		compatible = "marvell,88e1111";
		reg = <7>;
	} ;
}
Signed-off-by: NSadanand Mutyala <Sadanand.Mutyala@xilinx.com>
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add Micrel KSZ8841/KSZ8842 PCI Ethernet chip support.
Signed-off-by: NTristram Ha <Tristram.Ha@micrel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

i.MX51 babbage board has a FEC ethernet controller
Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The davinci EMAC peripheral is also available on other TI
platforms -notably TI AM3517 SoC. This patch modifies the
config option and the platform structure header files so that
the driver can be reused on non-davinci platforms as well.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Acked-by: NChaithrika U S <chaithrika@ti.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>

In order to use macvlan with qemu and other tools that require
a tap file descriptor, the macvtap driver adds a small backend
with a character device with the same interface as the tun
driver, with a minimum set of features.

Macvtap interfaces are created in the same way as macvlan
interfaces using ip link, but the netif is just used as a
handle for configuration and accounting, while the data
goes through the chardev. Each macvtap interface has its
own character device, simplifying permission management
significantly over the generic tun/tap driver.

Cc: Patrick McHardy <kaber@trash.net>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: David S. Miller" <davem@davemloft.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Or Gerlitz <ogerlitz@voltaire.com>
Cc: netdev@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current PS3 gelic wireless driver has support for wireless
extensions. The original PS3 gelic wireless driver exposed a
dedicated API for a dedicated wpa_supplicant driver. This old
API could be enabled with CONFIG_GELIC_WIRELESS_OLD_PSK_INTERFACE,
however, as this is not being used by any distros, and it is being
removed from the driver and from wpa_supplicant.
Signed-off-by: NHamish Guthrie <hamish.guthrie@sonycom.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

o Separate Ethernet driver for Qlogic CNA devices
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modifications for the Kconfig and network device Makefile to add the ixgbevf
driver module to the kernel plus basic driver documentation.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The option to support the old style PSK interface in the PS3
GELIC wireless drivers requires CONFIG_WEXT_PRIV to be set
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Octeon MGMT Ethernet ports are present in some members of the
Octeon SOC family (cn52XX and cn56XX have them).

The mdio bus connected to the MGMT PHYs is shared with the main
octeon-ethernet driver, we force it to be loaded first by calling
octeon_mdiobus_force_mod_depencency.  The platform devices for the
MGMT Ethernet ports are added in
arch/mips/cavium-octeon/octeon-platform.c, and the register
definitions for the ports live in arch/mips/include/asm/octeon/ along
with their ilk.

Although it currently is the only driver in drivers/net/octeon, the
directory was created looking forward to the day that octeon-ethernet
will move there from its current home in drivers/staging.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

From: Randy Dunlap <randy.dunlap@oracle.com>

niu drivers uses crc32 functions, so it needs to select CRC32.

niu.c:(.text+0x18a7f8): undefined reference to `crc32_le'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When building for Sun 3:

drivers/net/ethoc.c:1091: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `ethoc_probe':
drivers/net/ethoc.c:965: undefined reference to `dma_alloc_coherent'
drivers/net/ethoc.c:1063: undefined reference to `dma_free_coherent'
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes config dependency on x86 to build vmxnet3 driver. Thus
the driver can be built on big endian architectures now. Although vmxnet3
is not supported on VMs other than x86 architecture, all this code goes in
to ensure correctness. If the code is not dependent on x86, it should not
assume little endian architecture in any of its operations.
Signed-off-by: NShreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vmxnet3 uses in_dev* interfaces so it should depend on INET.
Also fix so that the driver builds when CONFIG_PCI_MSI is disabled.

vmxnet3_drv.c:(.text+0x2a88cb): undefined reference to `in_dev_finish_destroy'

drivers/net/vmxnet3/vmxnet3_drv.c:1335: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:1384: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:2137: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
drivers/net/vmxnet3/vmxnet3_drv.c:2138: error: 'struct vmxnet3_intr' has no member named 'msix_entries'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NBhavesh davda <bhavesh@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is the driver for the ST MAC 10/100/1000 on-chip Ethernet
controllers (Synopsys IP blocks).

Driver documentation:
 o http://stlinux.com/drupal/kernel/network/stmmac
Revisions:
 o http://stlinux.com/drupal/kernel/network/stmmac-driver-revisions
Performances:
 o http://stlinux.com/drupal/benchmarks/networking/stmmacSigned-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Randy Dunlap <randy.dunlap@oracle.com>

ks8851_mll uses mii interfaces so it needs to select MII.

ks8851_mll.c:(.text+0xf95ac): undefined reference to `generic_mii_ioctl'
ks8851_mll.c:(.text+0xf96a0): undefined reference to `mii_ethtool_gset'
ks8851_mll.c:(.text+0xf96fa): undefined reference to `mii_ethtool_sset'
ks8851_mll.c:(.text+0xf9754): undefined reference to `mii_link_ok'
ks8851_mll.c:(.text+0xf97ae): undefined reference to `mii_nway_restart'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>