The v4l2_subdev core s_power op was used for two different things: power on/off
sensors or video decoders/encoders and to put a tuner in standby (and only the
tuner!). There is no 'tuner wakeup' op, that's done automatically when the tuner
is accessed.

The danger with calling (s_power, 0) to put a tuner into standby is that it is
usually broadcast for all subdevs. So a video receiver subdev that supports
s_power will also be powered off, and since there is no corresponding (s_power, 1)
they will never be powered on again.

In addition, this is specifically meant for tuners only since they draw the most
current.

This patch adds a new tuner op called 'standby' and replaces all calls to
(core, s_power, 0) by (tuner, standby). This prevents confusion between the two
uses of s_power. Note that there is no overlap: bridge drivers either just want
to put the tuner into standby, or they deal with powering on/off sensors. Never
both.

This also makes it easier to replace s_power for the remaining bridge drivers
with some PM code later.

Whether we want something cleaner for tuners in the future is a separate topic.
There is a lot of legacy code surrounding tuners, and I am very hesitant about
making changes there.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Driver writers can benefit in knowing if/when callbacks are called in
interrupt context. But it is not completely obvious here, so document
it.
Signed-off-by: NLuca Ceresoli <luca@lucaceresoli.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

VB2_BUF_STATE_REQUEUEING is accepted by vb2_buffer_done() but not
documented, so add it along with notes about calls in interrupt
context.
Signed-off-by: NLuca Ceresoli <luca@lucaceresoli.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Documentation about what start_streaming() should do on failure are
scattered in two places and mostly duplicated, so consolidate them in
one of the two places.
Signed-off-by: NLuca Ceresoli <luca@lucaceresoli.net>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Fixed si470x_start() disabling the interrupt signal, causing tune
operations to never complete. This does not affect USB radios
because they poll the registers instead of using the IRQ line.
Signed-off-by: NDouglas Fischer <fischerdouglasc@gmail.com>
[hans.verkuil@cisco.com: fixed 80 column checkpatch warning]
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Added the call to v4l2_device_register() required to add a new radio device.
Without this patch, it is impossible for the driver to load. This does not
affect USB devices.
Signed-off-by: NDouglas Fischer <fischerdouglasc@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Fixed si470x_set_channel() trying to tune before chip is turned
on, which causes warnings in dmesg and when probing, makes driver
wait for 3s for tuning timeout. This issue did not affect USB
devices because they have a different probing sequence.
Signed-off-by: NDouglas Fischer <fischerdouglasc@gmail.com>
[hans.verkuil@cisco.com: fixed space-after-( checkpatch warning]
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add DCMI JPEG support.
Signed-off-by: NHugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Fix unnecessary parentheses in if conditions.
Detected by checkpatch.pl --strict.
Signed-off-by: NHugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Do not stop/restart dma on overrun or errors.
Dma will be restarted on current frame transfer
completion. Frame transfer completion is ensured
even if overrun or error occurs by DCMI continuous
capture mode which restarts data transfer at next
frame sync.
Do no warn on overrun while in irq thread, this slows down
system and lead to more overrun errors. Use a counter
instead and log errors at stop streaming.
Signed-off-by: NHugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Fix lock scheme leading to spurious freeze.
Signed-off-by: NHugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

v4l2_find_nearest_format is not useful for drivers in finding the best
matching format as it assumes a V4L2 specific struct. Drivers will use
v4l2_find_nearest_size instead.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add a function (as well as a helper macro) to obtain the best size in a
list of device specific sizes. This helps writing drivers as well as
aligns interface behaviour across drivers.

The struct in which this information is contained in is typically specific
to the driver, therefore the existing function v4l2_find_nearest_format()
does not address the need.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This renames the protocol for the imon rc driver from other to imon,
since it is now an known protocol. Although different name will show up
in the sysfs protocol file, loading a keymap using existing ir-keytable
versions still works.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This makes it possible to use the various iMON remotes with any raw IR
RC device.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

If there is IR in the raw kfifo when ir_raw_event_unregister() is called,
then kthread_stop() causes ir_raw_event_thread to be scheduled, decode
some scancodes and re-arm timer_keyup. The timer_keyup then fires when
the rc device is long gone.

Cc: stable@vger.kernel.org
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

These devices were supported by the lirc_imon.c driver which was removed
from staging in commit f41003a2 ("[media] staging: lirc_imon: port
remaining usb ids to imon and remove").
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Note that the stick on the remote is not supported yet.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This code was ported without the necessary hardware to test. There
are multiple problems which are more easily solved by writing a
separate driver.

This reverts commit f41003a2.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This patch updates documentation for Device-Tree bindings for sunxi IR
controller and adds the new optional property for the base clock
frequency.
Signed-off-by: NPhilipp Rossak <embed3d@gmail.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This patch updates the sunxi-ir driver to set the base clock frequency from
devicetree.

This is necessary since there are different ir receivers on the
market, that operate with different frequencies. So this value could be
set if the attached ir receiver needs a different base clock frequency,
than the default 8 MHz.
Signed-off-by: NPhilipp Rossak <embed3d@gmail.com>
Reviewed-by: NAndi Shyti <andi.shyti@samsung.com>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

There is a double sizeof() typo here so we don't duplicate the struct
properly.

Fixes: be7fd3c3 ("media: em28xx: Hauppauge DualHD second tuner functionality")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>

Like in ddbridge, get rid of all duplicated I2C client handling constructs
and rather make use of the newly added dvb_module_*() helpers. Makes
things more clean and removes the (cosmetic) need for some variables.

The check on a valid ptr on ci->en isn't really needed since the cxd2099
driver will set	it at a	time where it is going to return successfully
from probing.
Signed-off-by: NDaniel Scheller <d.scheller@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Instead of keeping duplicated I2C client handling construct, make use of
the newly introduced dvb_module_*() helpers. This not only keeps things
way cleaner and removes the need for duplicated I2C client attach code,
but even allows to get rid of some variables that won't help in making
things look cleaner anymore.

The check on a valid ptr on port->en isn't really needed since the cxd2099
driver will set it at a time where it is going to return successfully
from probing.
Signed-off-by: NDaniel Scheller <d.scheller@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The CIMaX SP2 driver is a EN50221 CI controller I2C driver similar to the
cxd2099 driver. Move it's Kconfig block into the newly introduced CI
subsection.

Cc: Olli Salonen <olli.salonen@iki.fi>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: NDaniel Scheller <d.scheller@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The cxd2099 driver makes use of the Regmap I2C kernel API, thus add
"select REGMAP_I2C" to it's Kconfig block. Also, make it default "m" if
!MEDIA_SUBDRV_AUTOSELECT, just like every other dvb-frontend driver.
And, while at it, remove the hyphens around the help tag.

Cc: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: NDaniel Scheller <d.scheller@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

If I2C is present and it is module, the DVB core should also
be a module, otherwise build will now fail with:

  drivers/media/dvb-core/dvbdev.o: In function `dvb_module_probe':
     drivers/media/dvb-core/dvbdev.c:965: undefined reference to `i2c_new_device'
     drivers/media/dvb-core/dvbdev.c:972: undefined reference to `i2c_unregister_device'
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

There's a comment there at s82168 that it is wrong.

With firmware 4.0.11, sleep/resume works well without
need of download it every time. But firmware 4.0.19
needs to be downloaded again after sleep.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

There are several undocumented v4l2-subdev functions that are
part of kAPI. Document them.
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

X-Virus-Scanned: Debian amavisd-new at dev.s-opensource.com
media: v4l2-subdev: get rid of __V4L2_SUBDEV_MK_GET_TRY() macro

The __V4L2_SUBDEV_MK_GET_TRY() macro is used to define
3 functions that have the same arguments. The code of those
functions is simple enough to just declare them, de-obfuscating
the code.

While here, replace BUG_ON() by WARN_ON() as there's no reason
why to panic the Kernel if this fails.
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

As warned by smatch:
	drivers/media/i2c/s5c73m3/s5c73m3-core.c:268 s5c73m3_check_status() error: uninitialized symbol 'status'.

if s5c73m3_check_status() is called too late, time_is_after_jiffies(end)
will return 0, causing the while to abort before reading status.

The current code will do the wrong thing here, as it will still
check if status != value. The right fix here is to change
the logic to ensure that it will always read the status.
Suggested-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

drivers/media/dvb-frontends/cxd2880/cxd2880_top.c: In function ‘cxd2880_set_ber_per_period_t’:
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c:677:34: warning: variable ‘c’ set but not used [-Wunused-but-set-variable]
  struct dtv_frontend_properties *c;
                                  ^
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c: In function ‘cxd2880_set_ber_per_period_t2’:
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c:790:34: warning: variable ‘c’ set but not used [-Wunused-but-set-variable]
  struct dtv_frontend_properties *c;
                                  ^
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c: In function ‘cxd2880_get_frontend’:
drivers/media/dvb-frontends/cxd2880/cxd2880_top.c:1799:23: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
  struct cxd2880_priv *priv = NULL;
                       ^~~~
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

drivers/media/dvb-frontends/cxd2880/cxd2880_devio_spi.c:59 cxd2880_io_spi_read_reg() error: uninitialized symbol 'ret'.
drivers/media/dvb-frontends/cxd2880/cxd2880_devio_spi.c:111 cxd2880_io_spi_write_reg() error: uninitialized symbol 'ret'.
drivers/media/dvb-frontends/cxd2880/cxd2880_tnrdmd.c:2985 cxd2880_tnrdmd_set_cfg() error: uninitialized symbol 'ret'.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

It is not needed anymore to include the dvb-core directory,
as all the public headers that used to be there was moved
to include/media.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This is the Makefile, Kconfig files of driver
and MAINTAINERS file update about the driver
for the Sony CXD2880 DVB-T2/T tuner + demodulator.
Signed-off-by: NYasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: NMasayuki Yamamoto <Masayuki.Yamamoto@sony.com>
Signed-off-by: NHideki Nozawa <Hideki.Nozawa@sony.com>
Signed-off-by: NKota Yonezawa <Kota.Yonezawa@sony.com>
Signed-off-by: NToshihiko Matsumoto <Toshihiko.Matsumoto@sony.com>
Signed-off-by: NSatoshi Watanabe <Satoshi.C.Watanabe@sony.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Fix a trivial conflict, where the location of DVB headers
got moved.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Provide monitor functions (DVB-T2)
for the Sony CXD2880 DVB-T2/T tuner + demodulator driver.
Signed-off-by: NYasunari Takiguchi <Yasunari.Takiguchi@sony.com>
Signed-off-by: NMasayuki Yamamoto <Masayuki.Yamamoto@sony.com>
Signed-off-by: NHideki Nozawa <Hideki.Nozawa@sony.com>
Signed-off-by: NKota Yonezawa <Kota.Yonezawa@sony.com>
Signed-off-by: NToshihiko Matsumoto <Toshihiko.Matsumoto@sony.com>
Signed-off-by: NSatoshi Watanabe <Satoshi.C.Watanabe@sony.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>