Some drivers (e.g. for ISA devices) have no parent device because there
is no associated bus driver. Allow the parent device to be NULL in
those cases when registering v4l2_device.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

get_index() had a limitation of 32 devices per driver. This was
unnecessarily strict and has been replaced with the maximum number
of devices. That should really satisfy anyone!
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add initial support for cameras based on the SQ Technologies SQ-905
chipset (USB ID 2770:9120) to V4L2 using the gspca infrastructure.
Currently only supports one resolution and doesn't attempt to inform
libv4l what image flipping options are needed.
Signed-off-by: NAdam Baker <linux@baker-net.org.uk>
Signed-off-by: NTheodore Kilgore <kilgota@auburn.edu>
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

- prevent application oops when the device is disconnected
- wake up the application at disconnection time
- check the disconnection in ioctl dqbuf and poll
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds functions to access the scratchpad.
For it is this good for? In the first two bytes, the developers
stored the HW/PCB version and the software release of the firmware.
This is now written to syslog, so debugging get's easier.
Also knowing the versions is the key for flash upgrades later on.

There are also some cleanups of the flash report sizes.

Altogether this should justify the new version number 1.0.9.

Thanks to Rick Bronson <rick@efn.org>
Signed-off-by: NTobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix typo in "DAB adapters" section in Kconfig.
Signed-off-by: NMárton Németh <nm127@freemail.hu>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added support for I2C device at address 0x40 and subaddress 0x0d/0x0b
that provides remote control key reading support for AVerMedia Cardbus
Hybrid card, possibly for other AVerMedia Cardbus cards.

The I2C address 0x40 doesn't like the SAA7134's 0xfd quirk, so it was
disabled.

[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: NOldřich Jedlička <oldium.pro@seznam.cz>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix printk format warning:

drivers/media/video/zoran/zoran_driver.c:345: warning: format '%lx' expects type 'long unsigned int', but argument 5 has type 'phys_addr_t'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With while (i++ < 10) { ... } i can reach 11, so callibration still
succeeds at i == 10.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

with while (try_count-- > 0) { ... } try_count reaches 0, not -1.

Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.

Cc: Jean-Francois Moine <moinejf@free.fr>
Cc: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is a common feature on many cameras. the options are:
Default colors,
B & W,
Sepia
Signed-off-by: NSergio Aguirre <saaguirre@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make correction to composite input plus svideo input to Avermedia E506R
Signed-off-by: NTim Farrington <timf@iinet.net.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Documents the driver usage functions, instead of the generic one used
by the videobuf specific handlers.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The bttv driver had static array of structures for up to 16 possible bttv
devices, even though few users have more than one or two.  The structures
were quite large and this resulted in a huge BSS segment.

Change the driver to allocate the bttv device data dynamically, which
changes "struct bttv bttvs[BTTV_MAX]" to "struct bttv *bttvs[BTTV_MAX]".
It would be nice to get ride of "bttvs" entirely but there are some
complications with gpio access from the audio & mpeg drivers.

To help bttvs removal along anyway, I changed the open() methods use the
video device's drvdata to get the driver data instead of looking it up in
the bttvs array.  This is also more efficient.  Some WARN_ON()s are added
in cases the device node exists by the bttv device doesn't, which I don't
think should be possible.

The gpio access functions need to check if bttvs[card] is NULL now.  Though
calling them on a non-existent card in the first place is wrong, but hard
to solve given the fundamental problems in how the gpio access code works.

This patch reduces the bss size by 66560 bytes on ia32.  Overall change is a
reduction of 66398 bytes, as the WARN_ON()s add some 198 bytes.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Over half of the card database was used to store muxsel data.  64 bytes
were used to store one 32 bit word for each of up to 16 inputs.

The Bt8x8 only has two bits to control its mux, so muxsel data for 16
inputs will fit into a single 32 bit word.  There were a couple cards that
had special muxsel data that didn't fit in two bits, but I cleaned them up
in earlier patches.

Unfortunately, C doesn't allow us to have an array of bit fields.  This
makes initializing the structure more of a pain.  But with some cpp magic,
we can do it by changing:
	.muxsel = { 2, 3, 0, 1 },
	.muxsel = { 2, 2, 2, 2, 3, 3, 3, 3, 1, 1 },
Into:
	.muxsel = MUXSEL(2, 3, 0, 1),
	.muxsel = MUXSEL(2, 2, 2, 2, 3, 3, 3, 3, 1, 1),

That's not so bad.  MUXSEL is a fancy macro that packs the arguments (of
which there can be one to sixteen!) into a single word two bits at a time.
It's a compile time constant (a variadic function wouldn't be) so we can
use it to initialize the structure.  It's important the the arguments to
the macro only be plain decimal integers.  Stuff like "0x01", "(2)", or
"MUX3" won't work properly.

I also created an accessor function, bttv_muxsel(btv, input), that gets the
mux bits for the selected input.  It makes it cleaner to change the way the
muxsel data is stored.

This patch doesn't change the code size and decreases the datasegment by
9440 bytes.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This card apparently uses an external mux and the Bt878's mux should always
be set to MUX2.  The values for the external mux control bits were stored
in the muxsel field.  This meant that when changing inputs the driver would
switch the Bt878's mux to whatever value the external mux was supposed to
be set to, then eagle_muxsel() would switch it back to MUX2 and program the
external mux.  This creates an unnecessary switch of the Bt878's mux.

So change muxsel to be 2 for each input.  The external mux bits are just
"input&3" so they don't really need to be stored anywhere.  This also
eliminates the last non-standard use of the muxsel data.

Cc: M G Berberich <berberic@fmi.uni-passau.de>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Old versions of the bttv driver would use the high nibble of an input's
muxsel value to program the GPIO lines enabled via gpiomask2.  Apparently
this was supposed to be for switching external audio muxes.  Anyway, the
code that did this was removed sometime in the pre-git 2.6 series.

The RemoteVision MX board used this feature to control an external video
mux and I guess no one noticed when they removed the code.

Move the extra gpio mux data out of the high nibble of muxsel and to
rv605_muxsel(), then have that function set the gpio lines with it.

From looking at the CD22M3494E datasheet, it seems like the mdelay(1) is a
much longer delay than necessary.  It looks like only around 20 ns is
necessary.

Cc: Miguel Freitas <miguel@cetuc.puc-rio.br>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Old versions of the bttv driver would use the high nibble of an input's
muxsel value to program the GPIO lines enabled via gpiomask2.  Apparently
this was supposed to be for switching external audio muxes.  Anyway, the
code that did this was removed sometime in the pre-git 2.6 series.

These phytec boards used this feature to control an external video mux and
I guess no one noticed when they removed the code.

So add a muxsel_hook for these boards that does the necessary gpio setting.

BTW, I doubt the needs_tvaudio setting for these cards is correct.

Cc: Dirk Heer <d.heer@phytec.de>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The card data for BTTV_BOARD_IVC120 set muxsel to a bunch of bogus values
(1 to 16), which the common mux code would use to set the Bt878's mux to
some random value.  Then the custom code in ivc120_muxsel() would change
the Bt878's mux to the right value (always MUX0).

Better to just make the muxsel data correct (all zeros, easy!) and get the
mux right to begin with.  Then the extra Bt878 mux setting code in
ivc120_muxsel() can be eliminated (the rest of the code for the IVC-120G's
external mux is still there of course).

This will help me clean up muxsel for some other changes.  It should also
get rid of an unnecessary mux switch when changing from certain inputs to
certain other inputs on the IVC-120G.

Cc: Alan Garfield <alan@fromorbit.com>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The code was using a muxsel value of -1U to indicate a digital input.  A
couple places in were checking of muxsel < 0 to detect this, which doesn't
work of course because muxsel is unsigned and can't be negative.

Only a couple cards had digital inputs and it was always the last one, so
for the card database create a one bit field that indicates the last input
is digital.  On init, this is used to set a new field in the bttv struct to
the digital input's number or UNSET for none.  This makes it easier to
check if the current input is digital.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The bttv card database is quite large and the data structure used to store
it wasn't very efficient.  Most of the field are only used at card
initialization time so it doesn't matter if they aren't efficient to
access.

Overall the changes reduce code size by 60 bytes in ia32.  The data size is
decreased by 5024 byes.  It is probably even more for 64-bit kernels.

Move the fields in the struct around to be sorted from largest to smallest.
This saves on padding space used for alignment.

Get rid of the unused digital_mode field.  Leave the setting as a comment
in the few cards entries that set it, in case someone ever writes the code.

Get rid of the unused audio_inputs field.  Leave the values in the card
entries in case someone ever writes code that might use it.

Get ride of the unused radio_addr field.  No card entries even set it to
anything interesting so it's not left as comments.  All the code that used
it was removed in commit v2.6.14-3466-g291d1d73 from Nov 8th 2005.

Reduce video_inputs to u8 as no card has more than 255 inputs (the most is
16).

Change tuner_addr to u8.  I2C addresses are only seven bits and 255 means
ADDR_UNSET, so everything fits.

Make has_radio a one bit flag.

Make the pll setting a two bit field.

Reduce svhs to four bits as no card has an s-video input above 9.  Change
the value for no s-video input from UNSET (which is -1U and out of range of
four bits) to NO_SVHS (which is now 15).
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The bttv card database structure had a "tuner" field that was the input
number of the tuner input or UNSET for no tuner.  However, the only values
it could ever be are 0 and UNSET.  Having a tuner on an input other than 0
didn't work and was never used.

There is also a "tuner_type" field that can be set to TUNER_ABSENT to
indicate no tuner, which makes "tuner = UNSET" redundant.  In many cases,
tuner_type was set to UNSET when there was no tuner, which isn't quite
correct.  tuner_type == UNSET is supposed to mean the tuner type isn't yet
known.

So, I changed cards where "tuner == UNSET" to always have tuner_type of
TUNER_ABSENT.  At this point the tuner field is redundant, so I deleted it.

I have the card setup code set the card's tuner_type (not the card type's
tuner_type!) to TUNER_ABSENT if it hasn't yet been set at the end of the
setup code.  Various places that check if the card has a tuner will now
look for this instead of checking the card type's "tuner" field.

Also autoload the tuner module before issuing the TUNER_SET_TYPE_ADDR I2C
client call instead of after issuing it.

Overall, on ia32 this decreases compiled code size by about 24 bytes and
reduces the data size by 640 bytes.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The code to set the norm for the TDA9880 analog demod was comparing
btv->norm, an index into the bttv driver's norm array, to V4L2_STD_NTSC,
which is a bit flag that's part of the V4L2 API.  This doesn't work of
course and results in the PAL path always being taken.

What's more, it modified the bttv_tvcards[] entries for cards using the
TDA9880.  This is wrong because changing the norm on one card will also
affect other cards of the same type.  Writing to bttv_tvcards is also bad
because it should be read-only or even devinitdata.

Changing the norm would also cause the audio to become unmuted.

Have the code get called for both norm setting and audio input setting
(which where the gpios are set) to avoid needed to modify bttv_tvcards.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The norm value in the driver is an index into an array and the the driver
doesn't allow it to be negative or otherwise invalid.  It should be
unsigned but wasn't in all places.

Fix some structs and functions to have the norm be unsigned.  Get rid of
useless checks for "< 0".  Most of the driver code can't handle a norm
value that's out of range, so change some ">= BTTV_TVNORMS" checks to
BUG_ON().  There's no point in silently ignoring invalid driver state just
to crash because of it later.
Reported-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added board Pinnacle Dazzle Video Creator Plus DVC107 to name description field.
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Coding style fixes for recent changesets in em28xx.
Signed-off-by: NNicola Soranzo <nsoranzo@tiscali.it>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Control arrays as are used with v4l2_ctrl_next must be sorted from
low to high. Add a comment at the top of all such arrays to warn
about this.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In order to convert the v4l1 zoran and vino i2c drivers to v4l2 these
extra ops are required.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The cx2341x_mpeg_ctrls array must be ordered by control ID. I know that
this is bad design, but for now I will just fix this bug and revisit it
when all drivers have moved to v4l2_device/v4l2_subdev, since that will
allow me to do greatly improve control handling.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>