Some encoders have both outputs low in stable states, others also have
a stable state with both outputs high (half-period mode) and some have
a stable state in all steps (quarter-period mode). The driver used to
support the former states and with this change it can also support the
later.

This commit also deprecates the 'half-period' property and introduces
a new property 'steps-per-period'. This property specifies the
number of steps (stable states) produced by the rotary encoder
for each GPIO period.
Signed-off-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Signed-off-by: NEzequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This commit makes uses of_property_read_bool() to read
boolean properties. This is just cosmetic cleanup.
Signed-off-by: NBen Gamari <bgamari.foss@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

There is an undocumented upper bound for the total number of ff effects:
    FF_GAIN (= 96).
This can be found as follows:
- user: write(EV_FF, effect_id, iterations)
    calls kernel: ff->playback(effect_id, ...): starts effect "effect_id"
- user: write(EV_FF, FF_GAIN, gain)
    calls kernel: ff->set_gain(gain, ...): sets gain

A collision occurs when effect_id equals FF_GAIN.
According to input_ff_event(),
FF_GAIN is the smallest value where a collision occurs.
Therefore the greatest safe value for effect_id is FF_GAIN - 1,
and thus the total number of effects should never exceed FF_GAIN.

Define FF_MAX_EFFECTS as FF_GAIN and check on this limit in ff-core.
Signed-off-by: NElias Vanderstuyft <elias.vds@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This changAdd support for EV_ABS / EV_REL events to the gpio-keys-polled driver.


The driver already allows specifying what type of events (key / rel / abs)
a button generates when pressed, but for rel / abs axis we also need to
specify which value this specific gpio represents.

One use case is digital joysticks / direction-pads which are hooked up to
gpio, in this case we've left and right buttons which we want to map to
EV_ABS, ABS_X and we want generate events for left with a value of -1 and
for right with a value of +1 (and similar for up / down and ABS_Y).
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

With commit 3fffd128 ("i2c: allow specifying separate wakeup
interrupt in device tree") wakeirq is managed by i2c-core, so remove
wakeirq related code from pixcir_i2c_ts driver.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This patch adds wake up support to GPIO rotary encoders.
Signed-off-by: NSylvain Rochet <sylvain.rochet@finsecur.com>
Reviewed-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Add new function input_enable_softrepeat() that allows drivers to
initialize their own values for input_dev->rep[REP_DELAY] and
input_dev->rep[REP_PERIOD], but also use the software autorepeat
functionality from input.c.

For example, a HID driver could do:

static void xyz_input_configured(struct hid_device *hid,
                                 struct hid_input *hidinput)
{
        input_enable_softrepeat(hidinput->input, 400, 100);
}

static struct hid_driver xyz_driver = {
        .input_configured = xyz_input_configured,
}
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

When we initialize the driver/device, we really don't know how many
controllers are connected.  So send a "query presence" command to the
base-station. (Command discovered by Zachary Lund)

Presence packet taken from:

https://github.com/computerquip/xpad5Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

To allow us to later create / destroy the input device from the urb
callback, we need to initialize/ deinitialize the input device from a
separate function.  So pull that logic out now to make later patches
more "obvious" as to what they do.
Signed-off-by: N"Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

as discussed here[0], x360w is the only pad that maps dpad_to_button.
This is bad for downstream developers as they have to differ between
x360 and x360w which is not intuitive.

This patch implements the suggested solution of exposing the dpad both
as axes and as buttons. This retains backward compatibility with software
already dealing with the difference while makes new software work as
expected across x360/ x360w pads.

[0] http://www.spinics.net/lists/linux-input/msg34421.htmlSigned-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Move submission logic to a single point at the end of the function.
This makes it easy to add locking/ queuing code later on.
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This code was probably wrong ever since and is redundant with
xpad_send_led_command. Both try to send a similar command to the xbox360
controller. However xpad_send_led_command correctly uses the pad_nr instead
of bInterfaceNumber to select the led and re-uses the irq_out URB instead
of creating a new one.

Note that this change only affects the two supported wireless controllers.
Tested using the xbox360 wireless controller (PC).
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The pad_nr corresponds to the lit up LED on the controller. Therefore there
should be no gaps when enumerating. Currently a LED is only re-assigned
after a controller is re-connected 4 times.

This patch uses ida to track connected pads - this way we can re-assign
freed up pad number immediately.

Consider the following case:
1. pad A is connected and gets pad_nr = 0
2. pad B is connected and gets pad_nr = 1
3. pad A is disconnected
4. pad A is connected again

using ida_simple_get() controller A now correctly gets pad_nr = 0 again.
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Rename led_no -> pad_nr: the number stored there is not the LED number - it
gets translated later on to a LED number in xpad_identify_controller;
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The "Razer Atrox Arcade Stick" features 10 buttons, and two of them (LT/RT)
don't work properly.  Change its definition in xpad_device[] (mapping
field) to fix.
Signed-off-by: NDario Scarpa <dario.scarpa@duskzone.it>
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

It is identical to the Xbox One controller but has a different product ID.
Signed-off-by: NPavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The copyright/license notice says that the code is licensed under GPL v2
only (not GPL v2+), so let's use proper string in MODULE_LICENSE().
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

There is no need to explicitly set .owner for the driver, the core will do
it for us.
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Since reset and wake pin are optional the gpio structure for those
pins may be null. Therefore, they can't be blindly passed to
desc_to_gpio.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Commit 5702222c ("Input: joydev - use memdup_user() to duplicate
memory from user-space") changed the kmalloc() and copy_from_user()
with a single call to memdup_user() but wrongly used the same error
path than the old code in which the buffer allocated by kmalloc() was
freed if copy_from_user() failed.

This is of course wrong since if memdup_user() fails, no memory was
allocated and the error in the error-valued pointer should be returned.

Fixes: 5702222c ("Input: joydev - use memdup_user() to duplicate
memory from user-space")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This adds support for ROHM BU21023/24 Dual touch resistive touchscreens.
Signed-off-by: NYoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Modify parkbd driver to use the new Parallel Port device model.
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The variable i is used to check the port to attach to and we are
supposed to save the reference of struct tgfx in the location given by
tgfx_base[i]. But after finding out the index, i is getting modified
again so we saved in a wrong index.

Fixes: 4de27a63 ("Input: turbografx - use parallel port device model")
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The variable i is used to check the port to attach to and we are
supposed to save the reference of struct gc in the location given by
gc_base[i]. But after finding out the index, i is getting modified again
so we saved in a wrong index.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Fixes: a517e87c ("Input: gamecon - use parallel port device model")
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The variable i is used to check the port to attach to and we are
supposed to save the reference of struct db9 in the location given by
db9_base[i]. But after finding out the index, i is getting modified again
so we saved in a wrong index.
While at it mark db9_base[i] as NULL after it is freed.

Fixes: 2260c419 ("Input: db9 - use parallel port device model")
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This adds support for the FT6x06 and the FT6x36 family of capacitive touch
panel controllers, in particular the FT6236.
Signed-off-by: NNoralf Trønnes <noralf@tronnes.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The PTR_ERR_OR_ZERO() helper function checks if a pointer contains an
errno code and returns it or return 0 if that's not the case. Use the
helper instead of open coding the same logic in the driver. This was
found with make coccicheck that complains with the following warning:

drivers/input/touchscreen/cyttsp4_i2c.c:53:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The PTR_ERR_OR_ZERO() helper function checks if a pointer contains an
errno code and returns it or return 0 if that's not the case. Use the
helper instead of open coding the same logic in the driver. This was
found with make coccicheck that complains with the following warning:

drivers/input/touchscreen/ads7846.c:532:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The invoked function already returns zero on success or a negative
errno code so there is no need to open code the logic in the caller.

This also fixes the following make coccicheck warning:

drivers/input/touchscreen/tps6507x-ts.c:57:5-8: WARNING: end returns can be simplified
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The invoked function already returns zero on success or a negative
errno code so there is no need to open code the logic in the caller.

This also fixes the following make coccicheck warnings:

end returns can be simplified and declaration on line 402 can be dropped
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The invoked function already returns zero on success or a negative
errno code so there is no need to open code the logic in the caller.

This also fixes the following make coccicheck warning:

end returns can be simplified and declaration on line 602 can be dropped
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: NHeiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The retval variable isn't needed since isn't used in the function. Remove
the variable and just return 0 instead.

This also fixes the following make coccicheck warning:

drivers/input/misc/kxtj9.c:638:5-11: Unneeded variable: "retval". Return "0" on line 646
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The memdup_user() helper function can be used to duplicate a memory region
from user-space to kernel-space. There is no need to open code the same
logic using kmalloc() and copy_from_user() instead. This was found with
make coccicheck that reported the following warning:

drivers/input/joydev.c:447:10-17: WARNING opportunity for memdup_user
drivers/input/joydev.c:483:10-17: WARNING opportunity for memdup_user
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The driver depends on GOLDFISH but there isn't a build dependency
so it's a good idea to allow the driver to be built even if that
option is disabled, if the COMPILE_TEST option is enabled.

That way, the driver can be built with a config generated by make
allyesconfig and can be checked if a patch would break the build.
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

In the cases where the gpio chip fails to acquire the current state an
error is reported back to gpio_keys. This is currently interpreted as if
the line went high, which just confuses the developer.

This patch introduces an error print in this case and skipps the
reporting of a input event; to aid in debugging this issue.
Reported-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

This reverts commit e51e3849: we
actually do want the device to work in extended W mode, as this is the
mode that allows us receiving multiple contact information.

Cc: stable@vger.kernel.org

It uses bitrev8(), so it must ensure that lib/bitrev.o gets included in
vmlinux.

Cc: Fengguang Wu <fengguang.wu@gmail.com>
Cc: yalin wang <yalin.wang2010@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add DA9062 OnKey support into the existing DA9063 OnKey driver component by
using generic access tables for common register and bit mask definitions.

The following change will add generic register and bit mask support to the
DA9063 OnKey.

The following alterations have been made to the DA9063 OnKey:

- Addition of a da906x_chip_config structure to hold all
  generic registers and bitmasks for this type of OnKey component.
- Addition of an struct of_device_id table for DA9063 and DA9062
  defaults
- Refactoring functions to use struct da9063_onkey accesses to generic
  registers/masks instead of using defines from registers.h
- Re-work of da9063_onkey_probe() to use of_match_node() and
  dev_get_regmap() to provide initialisation of generic registers and
  masks and access to regmap
Signed-off-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Modify walkera0701 driver to use the new Parallel Port device model.
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

Modify turbografx driver to use the new Parallel Port device model.
Signed-off-by: NSudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>