This patch (as1096) fixes an annoying problem: When a full-speed or
low-speed device is plugged into an EHCI controller, it fails to
enumerate at high speed and then is handed over to the companion
controller.  But usbcore logs a misleading and unwanted error message
when the high-speed enumeration fails.

The patch adds a new HCD method, port_handed_over, which asks whether
a port has been handed over to a companion controller.  If it has, the
error message is suppressed.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1095) cleans up the HCD glue and several of the EHCI
bus-glue files.  The ehci->is_tdi_rh_tt flag is redundant, since it
means the same thing as the hcd->has_tt flag, so it is removed and the
other flag used in its place.

Some of the bus-glue files didn't get the relinquish_port method added
to their hc_driver structures.  Although that routine currently
doesn't do anything for controllers with an integrated TT, in the
future it might.  So the patch adds it where it is missing.

Lastly, some of the bus-glue files have erroneous entries for their
hc_driver's suspend and resume methods.  These method pointers are
specific to PCI and shouldn't be used otherwise.

(The patch also includes an invisible whitespace fix.)
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>

This patch (as1094) changes the output of the "descriptors" binary
attribute.  Now it will contain the device descriptor followed by all
the configuration descriptors, not just the descriptor for the current
config.

Userspace libraries want to have access to the kernel's cached
descriptor information, so they can learn about device characteristics
without having to wake up suspended devices.  So far the only user of
this attribute is the new libusb-1.0 library; thus changing its
contents shouldn't cause any problems.

This should be considered for 2.6.26, if for no other reason than to
minimize the range of releases in which the attribute contains only the
current config descriptor.

Also, it doesn't hurt that the patch removes the device locking --
which was formerly needed in order to know for certain which config was
indeed current.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is a potential deadlock when the usb_generic driver is unbound
from a device.  The problem is that generic_disconnect() is called
with the device lock held, and it removes a bunch of device attributes
from sysfs.  If a user task happens to be running an attribute method
at the time, the removal will block until the method returns.  But at
least one of the attribute methods (the store routine for power/level)
needs to acquire the device lock!

This patch (as1093) eliminates the deadlock by moving the calls to
create and remove the sysfs attributes from the usb_generic driver
into usb_new_device() and usb_disconnect(), where they can be invoked
without holding the device lock.

Besides, the other sysfs attributes are created when the device is
registered and removed when the device is unregistered.  So it seems
only fitting for the extra attributes to be created and removed at the
same time.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Uninitialised Apple iSight drivers present with a distinctive USB ID.
Once firmware has been uploaded, they disconnect and reconnect with a
new ID. At this point they can be driven by the uvcvideo driver. As this
is unique to the Apple cameras and not functionality shared by any other
UVC devices, it makes sense to provide the firmware loading
functionality in a separate driver. This driver will read an isight.fw
file extracted from the Apple driver using the tools at
http://bersace03.free.fr/ift/ and upload it to the camera. It will also
handle the case where the device loses its firmware during hibernation
and must have it reloaded.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the range of PIDs
that have been allocated for FTDI based devices
at Matrix Orbital.

A small number of units have been shipped early 2008
with a faulty USB Descriptor.  Products that may have
this issue have been marked with the existing quirk to
work around the problem.
Signed-off-by: NR. Molenkamp <rmolenkamp@matrixorbital.ca>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 7329e211 ("USB: root hubs don't
lie about their number of TTs") requires the various platform EHCI
glue modules to set ->has_tt if the root hub has a Transaction
Translator.

The Orion EHCI root hub does have a Transaction Translator, so set
->has_tt in ehci_orion_setup().  This fixes oopsing on plugging in a
low speed device.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Acked-by: NNicolas Pitre <nico@marvell.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Recent USB-serial devices using the WinChipHead CH340/CH341 chipset are
being shipped with a new vendor/product ID code pair, but an otherwise
identical device.  (This is confirmed by looking at INF for the included
Windows driver.)

Patch is tested and working, both with new and old devices.
Signed-off-by: NMichael F. Robbins <mrobbins@mit.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

udc_disable oopses dereferencing udc_command.
Signed-off-by: NKarl Beldan <karl.beldan@gmail.com>
Acked-by: NRobert Jarzmik <rjarzmik@free.fr>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fixes the name of the onda MSA501HS device, I guess it is called
different things in different countries.
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds the Telit UC864-E HDSPA modem support to the option driver.
This lets their customers comply with the GPL instead of having to use a
binary driver from the manufacturer.

Cc: Simon Kissel <kissel@viprinet.com>
Cc: Nico Erfurth <ne@nicoerfurth.de>
Cc: Andrea Ghezzo <TS-EMEA@telit.com>
Cc: Dietmar Staps <Dietmar.Staps@telit.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch reverts 57833ea6
("usb-serial: pl2303: add support for RATOC REX-USB60F") and adds
support for the device to ftdi_sio driver.

Cc: Akira Tsukamoto <akirat@rd.scei.sony.co.jp>
Cc: stable <stable@kernel.org>
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is a race from when a device is created with device_create() and
then the drvdata is set with a call to dev_set_drvdata() in which a
sysfs file could be open, yet the drvdata will be NULL, causing all
sorts of bad things to happen.

This patch fixes the problem by using the new function,
device_create_drvdata().

Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is a race from when a device is created with device_create() and
then the drvdata is set with a call to dev_set_drvdata() in which a
sysfs file could be open, yet the drvdata will be NULL, causing all
sorts of bad things to happen.

This patch fixes the problem by using the new function,
device_create_drvdata().  It fixes all 3 phidget drivers, which all have
the same problem.

Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Sean Young <sean@mess.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Various fixes to Atmel's high speed UDC driver.

  * Issue some missing disconnect() calls.  Currently they are only made
    when VBUS power goes away (on boards where the driver can sense such
    changes), but that's not enough for gadget drivers to clean out all
    the state that's needed.  Missing calls were:

      - After USB reset, before starting enumeration.
      - When unregistering a gadget driver, before unbind().

  * Don't assume gadget drivers provide disconnect callbacks; make sure
    to not call through a null pointer!

  * When the driver doesn't provide an unbind() callback, refuse to
    unregister it.

Also remove two bogus "error" messages:

  * Related to mis-handling of disconnect() ... don't emit error messages
    for disconnect() handlers that disable endpoints.  All of them should
    be doing that; the problem is (unfixed) oddness in atmel_usba_udc.

  * Don't emit a diagnostic for a curious and transient nonfatal error
    that shows up sometimes with EP0.

Those messages spammed syslog, for no good reason.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Minor fixes to pxa27x udc driver :
 - don't clobber driver model bus_id field
 - wrong endianess fix (no functional change; cpu is little-endian)
 - double udc disable fix
 - resume/suspend fix (OTG hold bit)
 - make driver pxa27x dependant (check cpu at runtime)
Signed-off-by: NRobert Jarzmik <rjarzmik@free.fr>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On Mon, May 12, 2008 at 01:02:22AM -0700, David Brownell wrote:
> On Sunday 11 May 2008, Marcin Slusarz wrote:
> > 
> > test_ctrl_queue expects (?) positive and negative errnos.
> > what is going on here?
> 
> The sign is just a way to flag something:
> 
>                 /* some faults are allowed, not required */
> 
> The negative ones are required.  Positive codes are optional,
> in the sense that, depending on how the peripheral happens
> to be implemented, they won't necessarily be triggered.
> 
> For example, the test to fetch a device qualifier desriptor
> must succeed if the device is running at high speed.  So that
> test is marked as negative.  But when it's full speed, it
> could legitimately fail; marked as positive.  And so on for
> other tests.
> 
> Look at how the codes are *interpreted* to see it work.

Lets document it.

Based on comment from David Brownell <david-b@pacbell.net>.
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Microchip has changed the PICDEM FS USB demo device (0x04d8:000c)
to use bulk transfer and not interrupt transfer. So I've updated the libusb
based program here (Post #31).
	http://forum.microchip.com/tm.aspx?m=106426&mpage=2

So I believe that the in-kernel ldusb driver will no longer work with the
demo firmware.  It should be removed.
Signed-off-by: NXiaofan Chen <xiaofanc@gmail.com>
Cc: Michael Hund <MHund@LD-Didactic.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

New variant of the 5520 found by Luke Sheldrick.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Enables the SD-Card interface on the GI 0401 HSUPA card from Option.

The unusual_devs.h entry is necessary because the device descriptor is
vendor-specific. That prevents usb-storage from binding to it as an
interface driver.

This revised patch adds a small comment explaining why and reduces the
rev range.

T:  Bus=02 Lev=01 Prnt=01 Port=06 Cnt=01 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs=  1
P:  Vendor=0af0 ProdID=7401 Rev= 0.00
S:  Manufacturer=Option N.V.
S:  Product=Globetrotter HSUPA Modem
C:* #Ifs=10 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 0 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 2 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 4 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 5 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 5 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 6 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 6 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 7 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 7 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 9 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: NFilip Aben <f.aben@option.com>
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Bugfix some serial gadget descriptors:

 - Stop mangling the low bits (controller type ID) of bcdDevice;
   just use the high bits for a driver revision code.

 - Serial numbers that aren't specific to individual devices
   are useless; stop reporting "0" for this.

 - Since it's not part of a CDC-conformant function, the "bulk only"
   configuration shouldn't be using "CDC Data" as its interface class.
   Switch over to using CLASS_VENDOR_SPEC (different value, 0xff).
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Switch serial gadget away from a *very* old idiom:  just remember
the endpoints we'll be using, instead of looking them up by name
each time.  This is a net code and data (globals) shrink.

Also fix a small memory leak in the rmmod path, by working the
same as the disconnect code.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This removes a needless data structure from the serial gadget code;
it's a small code shrink, and a larger data shrink.

Since "struct usb_request" already has a "struct list_head" reserved
for use by gadget drivers, the serial gadget code doesn't need to
allocate wrapper structs to hold that list ... it can (and should!)
just use the list_head provided for that exact use.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some cleanup/reorg of g_serial ... simplifying it, and disentangling
its structure so morphing it into a "function" driver (combinable with
other interfaces) should be less painful.

 - Remove most forward declarations
     * put tty and gadget driver structs after their contents
     * snug module init/exit decls next to their functions
     * reordered some functions

 - Other cleanup:
     * convert a funky macro to an inline function
     * snug up module params next to their declarations
     * add missing driver.owner
     * add separator lines between major driver sections

 - Add comments re potential parameter/#define changes:
     * only supports one port (shrank GS_NUM_PORTS)
     * changing from 9600-8-N-1 affects multiple sites

 - Remove net2280-specific optimization ... it was being done
   way too late, can be done by net2280 module options, and in
   any case doesn't matter at any sane serial data rates.

There are no behavioral changes, but the macro thing saves I-space.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Al Borchers <alborchers@steinerpoint.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/usb/host/isp1760-if.c:275: warning: 'ret' is used uninitialized in this function
Signed-off-by: NSebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This device is not a serial port, but a virtual CD-ROM device. For
example with my Novatel MC950D:

lsusb -v -d 1410:5010 | grep InterfaceClass
      bInterfaceClass         8 Mass Storage

After some time (ca. 5min) or if virtual CD is ejected, device id
changes to 1410:4400:

% lsusb -v -d 1410:4400 | grep InterfaceClass
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceClass       255 Vendor Specific Class

Variable name says that 0x5010 is a Novatel U727, but searching in
internet shows, that this device also provides virtual CD that should be
ejected before use. Product id for serial port in this case is 0x4100.
Signed-off-by: NEugeniy Meshcheryakov <eugen@debian.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes ordering problems with entries in unusual_devs.h.
Signed-off-by: NPhil Dibowitz <phil@ipom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The patch below is a necessary workaround to support the Zoom Telephonics Model 3095F V.92 USB Mini External modem, which fails to initialise properly during normal probing thus:

May  3 22:53:00 imcfarla kernel: drivers/usb/class/cdc-acm.c: Zero length descriptor references
May  3 22:53:00 imcfarla kernel: cdc_acm: probe of 5-2:1.0 failed with error -22

Adding the patch below causes the probing section to be skipped, and the modem
then initialises correctly.
Signed-off-by: NIain McFarlane <iain@imcfarla.homelinux.net>
Acked-by: NOliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

the proposed patch allows the ET502HS HDSPA modem to be handled by the
"option" driver. It has been tested for 1 month and works reliably (no
oopses, no hangs, 300KB/s throughput).
Signed-off-by: NMauro Andreolini <andreoli@weblab.ing.unimo.it>
Signed-off-by: NMatthias Urlichs <matthias@urlichs.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The attached patch allows to bypass the ZeroCD mechanism for the ET502HS
HDSPA modem, so that it can be mounted as a network device.
Signed-off-by: NMauro Andreolini <andreoli@weblab.ing.unimo.it>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

drivers/usb/host/ohci-sm501.c:93:24: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3254:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3267:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3277:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3285:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/amd5536udc.c:3293:9: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix printk format warnings in isp1760 (in linux-next):

next-20080430/drivers/usb/host/isp1760-hcd.c:994: warning: format '%d' expects type 'int', but argument 6 has type 'size_t'
next-20080430/drivers/usb/host/isp1760-hcd.c:1092: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As reported by Magnus Boman <captain.magnus@opensuse.org>

Cc: Magnus Boman <captain.magnus@opensuse.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1087d) fixes a long-standing problem in usbcore: Device,
interface, and endpoint attributes aren't added until _after_ the
creation uevent has already been broadcast.

Unfortunately there are a few attributes which cannot be created that
early.  The "descriptors" attribute is binary and so must be created
separately.  The power-management attributes can't be created until
the dev/power/ group exists.  And the interface string can vary from
one altsetting to another, so it has to be created dynamically.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This should work on a KRZR K1m, and some other Motorola phones that do
not use the "standard" cdc ACM protocol to talk to USB hosts.
Tested-by: NJeff Garzik <jeff@garzik.org>
Cc: Jiang Dejun <a5652c@motorola.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes bug #10627 which caused the compilation error below.

  CC [M]  drivers/usb/c67x00/c67x00-ll-hpi.o
  drivers/usb/c67x00/c67x00-ll-hpi.c: In function `ll_recv_msg':
  drivers/usb/c67x00/c67x00-ll-hpi.c:243: erreur: `HZ' undeclared (first use in this function)
  drivers/usb/c67x00/c67x00-ll-hpi.c:243: erreur: (Each undeclared identifier is reported only once
  drivers/usb/c67x00/c67x00-ll-hpi.c:243: erreur: for each function it appears in.)
Signed-off-by: NFernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add ThinkOptics WavIt to cp2101 device table
Signed-off-by: NBernhard Beck <kernel@goodcoffee.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The file drivers/usb/serial/iuu_phoenix.c uses "int" for flags.  This can
cause hard to find bugs on some architectures.  This patch converts the flags
to use "long" instead.

This bug was discovered by doing an allyesconfig make on the -rt kernel where
checks are done to ensure all flags are of size sizeof(long).
Signed-off-by: NSteven Rostedt <srostedt@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Sparc doesn't have some of the OF interfaces this driver
wants to use.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>