With the 3.2-rc kernel, IOMMU 2M pages in KVM works.  But when I tried
to use IOMMU 1GB pages in KVM, I encountered an oops and the 1GB page
failed to be used.

The root cause is that 1GB page allocation calls gup_huge_pud() while 2M
page calls gup_huge_pmd.  If compound pages are used and the page is a
tail page, gup_huge_pmd() increases _mapcount to record tail page are
mapped while gup_huge_pud does not do that.

So when the mapped page is relesed, it will result in kernel oops
because the page is not marked mapped.

This patch add tail process for compound page in 1GB huge page which
keeps the same process as 2M page.

Reproduce like:
1. Add grub boot option: hugepagesz=1G hugepages=8
2. mount -t hugetlbfs -o pagesize=1G hugetlbfs /dev/hugepages
3. qemu-kvm -m 2048 -hda os-kvm.img -cpu kvm64 -smp 4 -mem-path /dev/hugepages
	-net none -device pci-assign,host=07:00.1

  kernel BUG at mm/swap.c:114!
  invalid opcode: 0000 [#1] SMP
  Call Trace:
    put_page+0x15/0x37
    kvm_release_pfn_clean+0x31/0x36
    kvm_iommu_put_pages+0x94/0xb1
    kvm_iommu_unmap_memslots+0x80/0xb6
    kvm_assign_device+0xba/0x117
    kvm_vm_ioctl_assigned_device+0x301/0xa47
    kvm_vm_ioctl+0x36c/0x3a2
    do_vfs_ioctl+0x49e/0x4e4
    sys_ioctl+0x5a/0x7c
    system_call_fastpath+0x16/0x1b
  RIP  put_compound_page+0xd4/0x168
Signed-off-by: NYouquan Song <youquan.song@intel.com>
Reviewed-by: NAndrea Arcangeli <aarcange@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If we encounter an efi_memory_desc_t without EFI_MEMORY_WB set
in ->attribute we currently call set_memory_uc(), which in turn
calls __pa() on a potentially ioremap'd address.

On CONFIG_X86_32 this is invalid, resulting in the following
oops on some machines:

  BUG: unable to handle kernel paging request at f7f22280
  IP: [<c10257b9>] reserve_ram_pages_type+0x89/0x210
  [...]

  Call Trace:
   [<c104f8ca>] ? page_is_ram+0x1a/0x40
   [<c1025aff>] reserve_memtype+0xdf/0x2f0
   [<c1024dc9>] set_memory_uc+0x49/0xa0
   [<c19334d0>] efi_enter_virtual_mode+0x1c2/0x3aa
   [<c19216d4>] start_kernel+0x291/0x2f2
   [<c19211c7>] ? loglevel+0x1b/0x1b
   [<c19210bf>] i386_start_kernel+0xbf/0xc8

A better approach to this problem is to map the memory region
with the correct attributes from the start, instead of modifying
it after the fact. The uncached case can be handled by
ioremap_nocache() and the cached by ioremap_cache().

Despite first impressions, it's not possible to use
ioremap_cache() to map all cached memory regions on
CONFIG_X86_64 because EFI_RUNTIME_SERVICES_DATA regions really
don't like being mapped into the vmalloc space, as detailed in
the following bug report,

	https://bugzilla.redhat.com/show_bug.cgi?id=748516

Therefore, we need to ensure that any EFI_RUNTIME_SERVICES_DATA
regions are covered by the direct kernel mapping table on
CONFIG_X86_64. To accomplish this we now map E820_RESERVED_EFI
regions via the direct kernel mapping with the initial call to
init_memory_mapping() in setup_arch(), whereas previously these
regions wouldn't be mapped if they were after the last E820_RAM
region until efi_ioremap() was called. Doing it this way allows
us to delete efi_ioremap() completely.
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Huang Ying <huang.ying.caritas@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1321621751-3650-1-git-send-email-matt@console-pimps.orgSigned-off-by: NIngo Molnar <mingo@elte.hu>

When HPET is operating in RTC mode, the TN_ENABLE bit on timer1
controls whether the HPET or the RTC delivers interrupts to irq8. When
the system goes into suspend, the RTC driver sends a signal to the
HPET driver so that the HPET releases control of irq8, allowing the
RTC to wake the system from suspend. The switchover is accomplished by
a write to the HPET configuration registers which currently only
occurs while servicing the HPET interrupt.

On some systems, I have seen the system suspend before an HPET
interrupt occurs, preventing the write to the HPET configuration
register and leaving the HPET in control of the irq8. As the HPET is
not active during suspend, it does not generate a wake signal and RTC
alarms do not work.

This patch forces the HPET driver to immediately transfer control of
the irq8 channel to the RTC instead of waiting until the next
interrupt event.
Signed-off-by: NMark Langsdorf <mark.langsdorf@amd.com>
Link: http://lkml.kernel.org/r/20111118153306.GB16319@alberich.amd.comTested-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org

arm-eabi-4.4.3-ld:--defsym zreladdr=: syntax error
make[2]: *** [arch/arm/boot/compressed/vmlinux] Error 1
make[1]: *** [arch/arm/boot/compressed/vmlinux] Error 2
make: *** [uImage] Error 2
Signed-off-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NJett.Zhou <jtzhou@marvell.com>

Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NGreg Ungerer <gerg@uclinux.org>

If we select a symbol it should have a type declared first
otherwise in some situations the config tools get upset. They
are currently perhaps a bit too resilient which is why this
wasn't noticed initially.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/20111206132811.4041.32549.stgit@bob.linux.org.ukSigned-off-by: NIngo Molnar <mingo@elte.hu>

We currently fail to build on CONFIG_X86_INTEL_MID=y and
CONFIG_X86_MRST unset.

We could build all the bits to make generic MID work if you
picked MID platform alone but that's really silly. Instead use
select and two variables.

This looks a bit daft right now but once we add a Medfield
selection it'll start to look a good deal more sensible.
Reported-by: NIngo Molnar <mingo@elte.hu>
Reported-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/20111205231433.28811.51297.stgit@bob.linux.org.ukSigned-off-by: NIngo Molnar <mingo@elte.hu>

Fix compile error due to missing <linux/module.h> include.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>

Otherwise timing is inaccurate, resulting in devices which depend on it,
like omap-keypad, broken.

Tested on Amstrad Delta.
Signed-off-by: NJanusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: removed comment referencing a development branch]
Signed-off-by: NTony Lindgren <tony@atomide.com>

I've received complaints that the numa_node attribute for family
15h model 00-0fh (e.g. Interlagos) northbridge functions shows
-1 instead of the proper node ID.

Correct this with attached quirks (similar to quirks for other
AMD CPU families used in multi-socket systems).
Signed-off-by: NAndreas Herrmann <andreas.herrmann3@amd.com>
Cc: Frank Arnold <frank.arnold@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/20111202072143.GA31916@alberich.amd.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Intel MID x86 platforms have a memory mapped virtual RTC
instead.  No MID platform have the default ports (and
accessing them may do weird stuff).
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Cc: feng.tang@intel.com
Cc: Feng Tang <feng.tang@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Fix an outstanding issue that has been reported since 2.6.37.
Under a heavy loaded machine processing "fork()" calls could
crash with:

BUG: unable to handle kernel paging request at f573fc8c
IP: [<c01abc54>] swap_count_continued+0x104/0x180
*pdpt = 000000002a3b9027 *pde = 0000000001bed067 *pte = 0000000000000000 Oops: 0000 [#1] SMP
Modules linked in:
Pid: 1638, comm: apache2 Not tainted 3.0.4-linode37 #1
EIP: 0061:[<c01abc54>] EFLAGS: 00210246 CPU: 3
EIP is at swap_count_continued+0x104/0x180
.. snip..
Call Trace:
 [<c01ac222>] ? __swap_duplicate+0xc2/0x160
 [<c01040f7>] ? pte_mfn_to_pfn+0x87/0xe0
 [<c01ac2e4>] ? swap_duplicate+0x14/0x40
 [<c01a0a6b>] ? copy_pte_range+0x45b/0x500
 [<c01a0ca5>] ? copy_page_range+0x195/0x200
 [<c01328c6>] ? dup_mmap+0x1c6/0x2c0
 [<c0132cf8>] ? dup_mm+0xa8/0x130
 [<c013376a>] ? copy_process+0x98a/0xb30
 [<c013395f>] ? do_fork+0x4f/0x280
 [<c01573b3>] ? getnstimeofday+0x43/0x100
 [<c010f770>] ? sys_clone+0x30/0x40
 [<c06c048d>] ? ptregs_clone+0x15/0x48
 [<c06bfb71>] ? syscall_call+0x7/0xb

The problem is that in copy_page_range() we turn lazy mode on,
and then in swap_entry_free() we call swap_count_continued()
which ends up in:

         map = kmap_atomic(page, KM_USER0) + offset;

and then later we touch *map.

Since we are running in batched mode (lazy) we don't actually
set up the PTE mappings and the kmap_atomic is not done
synchronously and ends up trying to dereference a page that has
not been set.

Looking at kmap_atomic_prot_pfn(), it uses
'arch_flush_lazy_mmu_mode' and doing the same in
kmap_atomic_prot() and __kunmap_atomic() makes the problem go
away.

Interestingly, commit b8bcfe99 ("x86/paravirt: remove lazy
mode in interrupts") removed part of this to fix an interrupt
issue - but it went to far and did not consider this scenario.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Looks like on some Acer Aspire 1s with older bioses, reboot via bios
fails.  It works on my machine, (with BIOS version 0.3310) but
not on some others (BIOS version 0.3309).

There's a log of problems at:

  https://bbs.archlinux.org/viewtopic.php?id=124136

This patch adds a different callback to the reboot quirk table,
to allow rebooting via keybaord controller.
Reported-by: NUroš Vampl <mobile.leecher@gmail.com>
Tested-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NPeter Chubb <peter.chubb@nicta.com.au>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1323093233-9481-1-git-send-email-anarsoul@gmail.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Following is from Notes of section 11.5.3 of Intel processor
manual available at:

  http://www.intel.com/Assets/PDF/manual/325384.pdf

For the Pentium 4 and Intel Xeon processors, after the sequence of
steps given above has been executed, the cache lines containing the
code between the end of the WBINVD instruction and before the
MTRRS have actually been disabled may be retained in the cache
hierarchy. Here, to remove code from the cache completely, a
second WBINVD instruction must be executed after the MTRRs have
been disabled.

This patch provides resolution for that.

Ideally, I will like to make changes only for Pentium 4 and Xeon
processors. But, I am not finding easier way to do it.
And, extra wbinvd() instruction does not hurt much for other
processors.
Signed-off-by: NAjaykumar Hotchandani <ajaykumar.hotchandani@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Link: http://lkml.kernel.org/r/4EBD1CC5.3030008@oracle.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Recently, I got bitten by using rdmsr_safe too early in the boot
process. Document its shortcomings for future reference.

Link: http://lkml.kernel.org/r/4ED5B70F.606@lwfinger.netSigned-off-by: NBorislav Petkov <borislav.petkov@amd.com>

The microcode update driver's initialization code does not handle
failures correctly. This patch fixes this issue.
Signed-off-by: NJan Beulich <JBeulich@suse.com>
Signed-off-by: NSrivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20111107123530.12164.31227.stgit@srivatsabhat.in.ibm.com
Link: http://lkml.kernel.org/r/4ED8E2270200007800065120@nat28.tlf.novell.comSigned-off-by: NBorislav Petkov <borislav.petkov@amd.com>

TAINT_FIRMWARE_WORKAROUND should be set when an MTRR fixup
is done.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Acked-by: NDavid Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/1318958650-12447-1-git-send-email-prarit@redhat.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

In commit f8924e77 ("x86: unify mp_bus_info"), the 32-bit
and 64-bit versions of MP_bus_info were rearranged to match each
other better.  Unfortunately it introduced a regression: prior
to that change we used to always set the mp_bus_not_pci bit,
then clear it if we found a PCI bus.  After it, we set
mp_bus_not_pci for ISA buses, clear it for PCI buses, and leave
it alone otherwise.

In the cases of ISA and PCI, there's not much difference.  But
ISA is not the only non-PCI bus, so it's better to always set
mp_bus_not_pci and clear it only for PCI.

Without this change, Dan's Dell PowerEdge 4200 panics on boot
with a log indicating interrupt routing trouble unless the
"noapic" option is supplied.  With this change, the machine
boots reliably without "noapic".

Fixes http://bugs.debian.org/586494Reported-bisected-and-tested-by: NDan McGrath <troubledaemon@gmail.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org	# 2.6.26+
Cc: Dan McGrath <troubledaemon@gmail.com>
Cc: Alexey Starikovskiy <aystarik@gmail.com>
[jrnieder@gmail.com: clarified commit message]
Signed-off-by: NJonathan Nieder <jrnieder@gmail.com>
Link: http://lkml.kernel.org/r/20111122215000.GA9151@elie.hsd1.il.comcast.netSigned-off-by: NIngo Molnar <mingo@elte.hu>

In latest firmware's SFI tables, pmic_gpio has been set to
IPC type of device, so we need handle it too.
Signed-off-by: NFeng Tang <feng.tang@intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Add SFI glue for the following devices:

tca6416: a gpio expander compatible with max7315
mpu3050: gyro sensor

Both of these actual drivers are already upstream
Signed-off-by: NJekyll Lai <jekyll_lai@wistron.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

On the Intel MID devices SCU commands are issued to manage power
off and the like. We need to issue different ones for
non-Lincroft based devices.
Signed-off-by: NAlek Du <alek.du@intel.com>
Signed-off-by: NJacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Dell OptiPlex 990 is known to require PCI reboot, so add it to
the reboot blacklist in pci_reboot_dmi_table[].
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Link: http://lkml.kernel.org/r/201111160019.51303.rjw@sisk.plSigned-off-by: NIngo Molnar <mingo@elte.hu>

Current partition information maintained in kernel does not match with
u-boot, this leads to corruption of u-boot env when we update uImage
from kernel. Patch fixes it to match with u-boot partition information.
Signed-off-by: NShankarmurthy,Akshay <akshay.s@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

On OMAP-L138 platform, EDMA event queue 0 should be used for audio
transfers so that they are not starved by video data moving on event queue 1.

Commit 48519f0a (ASoC: davinci: let platform
data define edma queue numbers) had a side-effect of changing this behavior
by making the driver actually honor the platform data passed.

Fix this now by passing event queue 0 as the queue to be used for audio
transfers.
Signed-off-by: NManjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Cc: <stable@vger.kernel.org> # v2.6.36.x and above

The function setup_vpif_input_channel_mode() used the VSCLKDIS register
instead of VIDCLKCTL. This meant that when in HD mode videoport channel 0
used a different clock from channel 1.

Clearly a copy-and-paste error.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NManjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Cc: stable@kernel.org

Fix the incorrect classification of DSP clock into a
seperate DSP domain on DM646x.

Per the reference guide (http://www.ti.com/lit/ug/spruep9e/spruep9e.pdf)
there is only one "AlwaysON" power domain on DM6467.
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Seperate PDSTAT and PDCTL registers are defined for
domain 0 and domain 1 where as the code always reads
the domain 0 PDSTAT register and domain 1 PDCTL register.

Fix this issue. While at it, introduce usage of macros
for register masks to improve readability.
Reviewed-by: NSergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

There are 5 LSB bits defined in PDSTAT and the code
currently uses a mask of 1 bit to check the status.

Use a proper mask per the hardware specification.
While at it, use a #define for the mask to improve
readability.
Reviewed-by: NSergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

There was a mixup when the SGI UV2 hub chip was sent to be
fabricated, and it ended up with the wrong part number in the
HRP_NODE_ID mmr. Future versions of the chip will (may) have the
correct part number. Change the UV infrastructure to recognize
both part numbers as valid IDs of a UV2 hub chip.
Signed-off-by: NJack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/20111129210058.GA20452@sgi.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

The kernel stack overflow is checked in stack_overflow_check(),
which may wrongly detect the overflow if the stack pointer in
user space points to the kernel stack intentionally or
accidentally. So, the actual overflow is never detected after
this misdetection because WARN_ONCE() is used on the detection
of it.

This patch adds user-mode-vm checking before it to avoid this
problem and bails out early if the user stack is used.
Signed-off-by: NMitsuo Hayasaka <mitsuo.hayasaka.hu@hitachi.com>
Cc: yrl.pp-manager.tt@hitachi.com
Cc: Randy Dunlap <rdunlap@xenotime.net>
Link: http://lkml.kernel.org/r/20111129060821.11076.55315.stgit@ltc219.sdl.hitachi.co.jpSigned-off-by: NIngo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>

On AMD family 10h we see firmware bug messages like the following:

 [Firmware Bug]: cpu 6, try to use APIC500 (LVT offset 0) for vector 0x10400, but the register is already in use for vector 0xf9 on another cpu
 [Firmware Bug]: cpu 6, IBS interrupt offset 0 not available (MSRC001103A=0x0000000000000100)
 [Firmware Bug]: using offset 1 for IBS interrupts
 [Firmware Bug]: workaround enabled for IBS LVT offset
 perf: AMD IBS detected (0x00000007)

We always see this, since the offsets are not assigned by the BIOS for
this family. Force LVT offset assignment in this case. If the OS
assignment fails, fallback to BIOS settings and try to setup this.

The fallback to BIOS settings weakens the family check since
force_ibs_eilvt_setup() may fail e.g. in case of virtual machines.
But setup may still succeed if BIOS offsets are correct.

Other families don't have a workaround implemented that assigns LVT
offsets. It's ok, to drop calling force_ibs_eilvt_setup() for that
families.

With the patch the [Firmware Bug] messages vanish. We see now:

 IBS: LVT offset 1 assigned
 perf: AMD IBS detected (0x00000007)
Signed-off-by: NRobert Richter <robert.richter@amd.com>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20111109162225.GO12451@erda.amd.comSigned-off-by: NIngo Molnar <mingo@elte.hu>

Cc: Stephane Eranian <eranian@google.com>
Cc: stable@kernel.org
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

People with old AMD chips are getting hung boots, because commit
bcb80e53 ("x86, microcode, AMD: Add microcode revision to
/proc/cpuinfo") moved the microcode detection too early into
"early_init_amd()".

At that point we are *so* early in the booth that the exception tables
haven't even been set up yet, so the whole

	rdmsr_safe(MSR_AMD64_PATCH_LEVEL, &c->microcode, &dummy);

doesn't actually work: if the rdmsr does a GP fault (due to non-existant
MSR register on older CPU's), we can't fix it up yet, and the boot fails.

Fix it by simply moving the code to a slightly later point in the boot
(init_amd() instead of early_init_amd()), since the kernel itself
doesn't even really care about the microcode patchlevel at this point
(or really ever: it's made available to user space in /proc/cpuinfo, and
updated if you do a microcode load).
Reported-tested-and-bisected-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NBob Tracy <rct@gherkin.frus.com>
Acked-by: NBorislav Petkov <borislav.petkov@amd.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We provided very similar routines internally, but now we can hook
into the generic framework by supplying our routines as function
pointers in the irq_chip structure instead.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>

When freeing the page with this API, the page was "put" twice.
This was only discovered bringing up an MPT fusion controller, which
actually used the API; it hadn't been invoked previously, so the bug
had gone unnoticed.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>

The empty_zero_page[] export is required for ZERO_PAGE() module references.
The #includes are due to changes in implicit inclusion, and should of
course have been in the sources from the beginning.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>

The idea behind commit d91ee586 ("cpuidle: replace xen access to x86
pm_idle and default_idle") was to have one call - disable_cpuidle()
which would make pm_idle not be molested by other code.  It disallows
cpuidle_idle_call to be set to pm_idle (which is excellent).

But in the select_idle_routine() and idle_setup(), the pm_idle can still
be set to either: amd_e400_idle, mwait_idle or default_idle.  This
depends on some CPU flags (MWAIT) and in AMD case on the type of CPU.

In case of mwait_idle we can hit some instances where the hypervisor
(Amazon EC2 specifically) sets the MWAIT and we get:

  Brought up 2 CPUs
  invalid opcode: 0000 [#1] SMP

  Pid: 0, comm: swapper Not tainted 3.1.0-0.rc6.git0.3.fc16.x86_64 #1
  RIP: e030:[<ffffffff81015d1d>]  [<ffffffff81015d1d>] mwait_idle+0x6f/0xb4
  ...
  Call Trace:
   [<ffffffff8100e2ed>] cpu_idle+0xae/0xe8
   [<ffffffff8149ee78>] cpu_bringup_and_idle+0xe/0x10
  RIP  [<ffffffff81015d1d>] mwait_idle+0x6f/0xb4
   RSP <ffff8801d28ddf10>

In the case of amd_e400_idle we don't get so spectacular crashes, but we
do end up making an MSR which is trapped in the hypervisor, and then
follow it up with a yield hypercall.  Meaning we end up going to
hypervisor twice instead of just once.

The previous behavior before v3.0 was that pm_idle was set to
default_idle regardless of select_idle_routine/idle_setup.

We want to do that, but only for one specific case: Xen.  This patch
does that.

Fixes RH BZ #739499 and Ubuntu #881076
Reported-by: NStefan Bader <stefan.bader@canonical.com>
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It's a correction of two macro names, renaming them from IRADC to LRADC.
Signed-off-by: NPeter Rusko <rusko.peter@prolan.hu>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Adding the machine_is_* line was forgotten when converting mach-stmp378x to
mach-mxs.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: stable@kernel.org

Initializers of m28evk and stmp378x_devb fixed to be in order
they are called.

reference: http://article.gmane.org/gmane.linux.ports.arm.omap/50721

Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: NLauri Hintsala <lauri.hintsala@bluegiga.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>