We are disabling of interrupts from firmware in freeze handler.
Also setting power management capability KEEP_MMC_POWER to make
device wakeup for WoWLAN trigger.
At restore, we observed a device reset on some platforms. Hence
reloading of firmware and device initialization is performed.
Signed-off-by: NKarun Eagalapati <karun256@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

WoWLAN is supported in RS9113 device through GPIO pin2.
wowlan config frame is internally sent to firmware in mac80211
suspend handler. Also beacon miss threshold and keep-alive time
values are increased to avoid un-necessary disconnection with AP.
Signed-off-by: NKarun Eagalapati <karun256@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add P2P_GO condition as well when handling BEACON_ENABLE
from mac80211. Also passing 'vif' for auto rate request.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When AP or P2P GO VAP is running, power save configuration should
be disallowed. To check interface type in power save configuration
'vif' parameters is passed.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Data descriptor is updated to include vap_id. TX command frame
key config also updated to include vap_id.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Parameter 'vif' is passed to inform_bss_status function to
check the type of vif and to get vap_id.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Remain-on-channel and cancel-remain-on-channel are implemented
to support p2p listen phase.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

STA_OPMODE and AP_OPMODE macros are renamed to RSI_OPMODE_STA
and RSI_OPMODE_AP. New opmodes are added to this list for P2P
support. Mapping of mac80211 interface types to rsi interface
types are added.
Add and remove interface callbacks are handled for P2P mode.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Station id should be set in load key frame configured to device.
For WEP mode, key is configured once from mac80211. This key is
saved and configured to device every time a station is connected.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

TX command frame ampdu aggregation parameters is updated to
include sta_id for AP mode.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Auto rate frame is sent to firmware when a new station is
connected. Station id and station's ht capabilities are updated
in auto rate command frame.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

TX command frame auto rate request is modified to use common
descriptor struture.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Station structures are maintained in driver with required
fields. When mac80211 callback sta_add is called, driver
iterates through list of connected stations to check available
index and assigns station id which is important for further
communication to that station. Then peer notify frame is send
to firmware to inform the firmware about new station connection.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Mac80211 config parameter BEACON_ENABLE is handled. When VAP
capabilities frame with AP mode is configured to firmware, beacon
events start coming to host at each PreTBTT. At this time, beacon
is taken from mac80211, descriptor is prepared and send to firmware.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

AP mode is handled in add_interface callback of mac80211.
Also for AP mode, sending rx filter frame to disallow beacons
to host is added. Station structures are initialized to NULL.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Provision is added for configuring RTS threshold by sending
vap dynamic update frame to firmware.
Signed-off-by: NKarun Eagalapati <karun256@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for U-APSD power save. Configuration
frame is downloaded to firmware with default settings and
support is advertised to mac80211
Signed-off-by: NKarun Eagalapati <karun256@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for legacy power save. Necessary
configuration frames are downloaded to firmware when power save
is enabled/disabled
Signed-off-by: NKarun Eagalapati <karun256@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

TX command frame set_antenna is modified to use common
descriptor structure. Also it's subframe type is set.
Signed-off-by: NPavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fixes the uninitialized descriptor pointer
issue in function rsi_send_internal_mgmt_frame().
Descriptor should point to start of the skb data.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Fixes: 9a629faf ("rsi: immediate wakeup bit and priority for TX command packets")
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

TX command frame block/unblock data is modified to
use common descriptor structure.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Data queues should be unblocked after station add notify frame
is sent and should be blocked after station delete notify is sent.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When Short Gaurd Interval is enabled bit 9 is set in rate. Otherwise
it should not be set. Added missing 'else' case in this patch.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Broadcast bit to be set for broadcast and multicast packets.
For remove_key, tx and rx mic need not be filled.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

TX command frame set_key is modified to use common descriptor
structure.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

VAP capablities frame configured to device is modified to use
common descriptor structure.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

TX command frame set_channel is modified to use common
descriptor structure. Also DFS channel indication to firmware
is added in the descriptor for dfs channels configuration.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Baseband RF programming frame configured to device is modified
to use common descriptor structure.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

AMPDU aggregation parameters frame configured to device is
modified to use common descriptor structure.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

TX command frame peer notify is updated to use common descriptor
structure. MPDU density value added to the frame.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The function rsi_mgmt_pkt_to_core() is for passing the 802.11
management frames to mac80211. So, it is unnecessary to check
again for the frame type 802.11 management in this function.
It can be checked before passing to this function.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Radio capabilities frame is updated to use common descriptor
structure. Also, few changes to this frame is done like hardware
queues are increase to 12 from 8, default channel number is included.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For all TX command packets immediate wakeup bit needs to be
set in descriptor. This will make sure device will wakeup if it
is in any sleep state. Priority of the packet is also set.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

EEPROM read frame is sent during device initialization to read mac address.
The format of the frame is modified in firmware to include eeprom length
and offset. This frame does not return firmware version now. Also same
frame is sent again to read rf type and band information.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

After successful loading of firmware, a CARD READY indication is
received by host. Common device configuration parameters are sent
to the device after this. It includes information like device
operating mode (Wi-Fi alone or BT coex), power save related
parameters, GPIO information etc. As device supports BT coex,
this frame is send in COEX queue initially. Based on the operating
mode, CARD READY indication is received from each protocol module
in firmware i.e. WLAN, BT.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Boot parameters are changed in new firmware. Also three
new sdio sleep parameters are added for ultra low power
save.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NAmitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Signed-off-by: Nyuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.

An spatch similar to the one for skb_put_zero() converts many
of the places using it:

    @@
    identifier p, p2;
    expression len, skb, data;
    type t, t2;
    @@
    (
    -p = skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    |
    -p = (t)skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, len);
    |
    -memcpy(p, data, len);
    )

    @@
    type t, t2;
    identifier p, p2;
    expression skb, data;
    @@
    t *p;
    ...
    (
    -p = skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    |
    -p = (t *)skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, sizeof(*p));
    |
    -memcpy(p, data, sizeof(*p));
    )

    @@
    expression skb, len, data;
    @@
    -memcpy(skb_put(skb, len), data, len);
    +skb_put_data(skb, data, len);

(again, manually post-processed to retain some comments)
Reviewed-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Transmit power level in a channel is determined based on the dfs region.
To support regulatory rules dfs region should be configured to device during
set channel request. Also antenna gain values are taken from the mac80211
channel parameters instead of fixed values.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

RSI 9113 device supports single antenna for tx and rx. Support for using
external is added. This can be configured from user space using iw.
Signed-off-by: NPrameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>