This patch adds arch specific code for kernel address sanitizer
(see Documentation/kasan.txt).

1/8 of kernel addresses reserved for shadow memory. There was no
big enough hole for this, so virtual addresses for shadow were
stolen from vmalloc area.

At early boot stage the whole shadow region populated with just
one physical page (kasan_zero_page). Later, this page reused
as readonly zero shadow for some memory that KASan currently
don't track (vmalloc).
After mapping the physical memory, pages for shadow memory are
allocated and mapped.

Functions like memset/memmove/memcpy do a lot of memory accesses.
If bad pointer passed to one of these function it is important
to catch this. Compiler's instrumentation cannot do this since
these functions are written in assembly.
KASan replaces memory functions with manually instrumented variants.
Original functions declared as weak symbols so strong definitions
in mm/kasan/kasan.c could replace them. Original functions have aliases
with '__' prefix in name, so we could call non-instrumented variant
if needed.
Some files built without kasan instrumentation (e.g. mm/slub.c).
Original mem* function replaced (via #define) with prefixed variants
to disable memory access checks for such files.
Signed-off-by: NAndrey Ryabinin <ryabinin.a.a@gmail.com>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This will be used by KASAN latter.
Signed-off-by: NAndrey Ryabinin <ryabinin.a.a@gmail.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Commit 654672d4 ("locking/atomics: Add _{acquire|release|relaxed}()
variants of some atomic operation") introduced a relaxed atomic API to
Linux that maps nicely onto the arm64 memory model, including the new
ARMv8.1 atomic instructions.

This patch hooks up the API to our relaxed atomic instructions, rather
than have them all expand to the full-barrier variants as they do
currently.
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Since arm64 does not use a builtin decompressor, the EFI stub is built
into the kernel proper. So far, this has been working fine, but actually,
since the stub is in fact a PE/COFF relocatable binary that is executed
at an unknown offset in the 1:1 mapping provided by the UEFI firmware, we
should not be seamlessly sharing code with the kernel proper, which is a
position dependent executable linked at a high virtual offset.

So instead, separate the contents of libstub and its dependencies, by
putting them into their own namespace by prefixing all of its symbols
with __efistub. This way, we have tight control over what parts of the
kernel proper are referenced by the stub.
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: NMatt Fleming <matt.fleming@intel.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

For more control over which functions are called with the MMU off or
with the UEFI 1:1 mapping active, annotate some assembler routines as
position independent. This is done by introducing ENDPIPROC(), which
replaces the ENDPROC() declaration of those routines.
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

A prior commit used to detect the hw breakpoint ABI behaviour based on
the target state missed the asm/compat.h include and the build fails
with !CONFIG_COMPAT.

Fixes: 8f48c062 ("arm64: hw_breakpoint: use target state to determine ABI behaviour")
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

When cpu is disabled, all irqs will be migratged to another cpu.
In some cases, a new affinity is different, the old affinity need
to be updated and if irq_set_affinity's return value is IRQ_SET_MASK_OK_DONE,
the old affinity can not be updated. Fix it by using irq_do_set_affinity.

And migrating interrupts is a core code matter, so use the generic
function irq_migrate_all_off_this_cpu() to migrate interrupts in
kernel/irq/migration.c.

Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

With 64k pages, the next larger segment size is 512M. The linux
kernel also uses different protection flags to cover its code and data.
Because of this requirement, the vast majority of the kernel code and
data structures end up being mapped with 64k pages instead of the larger
pages common with a 4k page kernel.

Recent ARM processors support a contiguous bit in the
page tables which allows the a TLB to cover a range larger than a
single PTE if that range is mapped into physically contiguous
ram.

So, for the kernel its a good idea to set this flag. Some basic
micro benchmarks show it can significantly reduce the number of
L1 dTLB refills.

Add boot option to enable/disable CONT marking, as well as fix a
bug found by Steve Capper.
Signed-off-by: NJeremy Linton <jeremy.linton@arm.com>
[catalin.marinas@arm.com: remove CONFIG_ARM64_CONT_PTE altogether]
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The kernel page dump utility needs to be aware of the CONT bit before
it will break up pages ranges for display.
Signed-off-by: NJeremy Linton <jeremy.linton@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The default page attributes for a PMD being broken should have the CONT bit
set. Create a new definition for an early boot range of PTE's that are
contiguous.
Signed-off-by: NJeremy Linton <jeremy.linton@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Add the supporting macros to check if the contiguous bit
is set, set the bit, or clear it in a PTE entry.
Signed-off-by: NJeremy Linton <jeremy.linton@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Define the bit positions in the PTE and PMD for the
contiguous bit.
Signed-off-by: NJeremy Linton <jeremy.linton@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Add the number of pages required to form a contiguous range,
as well as some supporting constants.
Signed-off-by: NJeremy Linton <jeremy.linton@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The A57 and A53 PMUs in Juno support different events, so describe them
separately in both the Juno and Juno R1 DTs.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The Cortex-A57 PMU supports a few events outside of the required PMUv3
set that are rather useful.

This patch adds the event map data for said events.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The Cortex-A53 PMU supports a few events outside of the required PMUv3
set that are rather useful.

This patch adds the event map data for said events.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Now that the arm_pmu framework has been factored out to drivers/perf we
can make use of it for arm64, gaining support for heterogeneous PMUs
and unifying the two codebases before they diverge further.

The as yet unused PMU name for PMUv3 is changed to armv8_pmuv3, matching
the style previously applied to the 32-bit PMUs.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The arm64 hw_breakpoint interface is slightly less flexible than its
32-bit counterpart, thanks to some changes in the architecture rendering
unaligned watchpoint addresses obselete for AArch64.

However, in a multi-arch environment (i.e. debugging a 32-bit target
with a 64-bit GDB under a 64-bit kernel), we need to provide a feature
compatible interface to GDB in order for debugging to function correctly.

This patch adds a new helper, is_compat_bp,  to our hw_breakpoint
implementation which changes the interface behaviour based on the
architecture of the debug target as opposed to the debugger itself.
This allows debugged to function as expected for multi-arch
configurations without relying on deprecated architectural behaviours
when debugging native applications.

Cc: Yao Qi <yao.qi@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

update_mmu_cache() consists of a dsb(ishst) instruction so that new user
mappings are guaranteed to be visible to the page table walker on
exception return.

In reality this can be a very expensive operation which is rarely needed.
Removing this barrier shows a modest improvement in hackbench scores and
, in the worst case, we re-take the user fault and establish that there
was nothing to do.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

__flush_tlb_pgtable is used to invalidate intermediate page table
entries after they have been cleared and are about to be freed. Since
pXd_clear imply memory barriers, we don't need the extra one here.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

mm_cpumask isn't actually used for anything on arm64, so remove all the
code trying to keep it up-to-date.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

switch_mm performs some checks to try and avoid entering the ASID
allocator:

  (1) If we're switching to the init_mm (no user mappings), then simply
      set a reserved TTBR0 value with no page table (the zero page)

  (2) If prev == next *and* the mm_cpumask indicates that we've run on
      this CPU before, then we can skip the allocator.

However, there is plenty of redundancy here. With the new ASID allocator,
if prev == next, then we know that our ASID is valid and do not need to
worry about re-allocation. Consequently, we can drop the mm_cpumask check
in (2) and move the prev == next check before the init_mm check, since
if prev == next == init_mm then there's nothing to do.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The TLB gather code sets fullmm=1 when tearing down the entire address
space for an mm_struct on exit or execve. Given that the ASID allocator
will never re-allocate a dirty ASID, this flushing is not needed and can
simply be avoided in the flushing code.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The ASID macro returns a 64-bit (long long) value, so there is no need
to cast to (unsigned long) before shifting prior to a TLBI operation.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

Our current switch_mm implementation suffers from a number of problems:

  (1) The ASID allocator relies on IPIs to synchronise the CPUs on a
      rollover event

  (2) Because of (1), we cannot allocate ASIDs with interrupts disabled
      and therefore make use of a TIF_SWITCH_MM flag to postpone the
      actual switch to finish_arch_post_lock_switch

  (3) We run context switch with a reserved (invalid) TTBR0 value, even
      though the ASID and pgd are updated atomically

  (4) We take a global spinlock (cpu_asid_lock) during context-switch

  (5) We use h/w broadcast TLB operations when they are not required
      (e.g. in flush_context)

This patch addresses these problems by rewriting the ASID algorithm to
match the bitmap-based arch/arm/ implementation more closely. This in
turn allows us to remove much of the complications surrounding switch_mm,
including the ugly thread flag.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

There are a number of places where a single CPU is running with a
private page-table and we need to perform maintenance on the TLB and
I-cache in order to ensure correctness, but do not require the operation
to be broadcast to other CPUs.

This patch adds local variants of tlb_flush_all and __flush_icache_all
to support these use-cases and updates the callers respectively.
__local_flush_icache_all also implies an isb, since it is intended to be
used synchronously.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NDavid Daney <david.daney@cavium.com>
Acked-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

When cold-booting a CPU, we must invalidate any junk entries from the
local TLB prior to enabling the MMU. This doesn't require broadcasting
within the inner-shareable domain, so de-scope the operation to apply
only to the local CPU.
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Tested-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

With commit b08d4640 ("arm64: remove dead code"),
cpu_set_idmap_tcr_t0sz is no longer called and can therefore be removed
from the kernel.

This patch removes the function and effectively inlines the helper
function __cpu_set_tcr_t0sz into cpu_set_default_tcr_t0sz.
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

In order to not use lengthy (UL(0xffffffffffffffff) << VA_BITS) everywhere,
replace it with VA_START.
Signed-off-by: NAndrey Ryabinin <ryabinin.a.a@gmail.com>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch optimize copy_to-from-in_user for arm 64bit architecture. The
copy template is used as template file for all the copy*.S files. Minor
change was made to it to accommodate the copy to/from/in user files.
Signed-off-by: NFeng Kan <fkan@apm.com>
Signed-off-by: NBalamurugan Shanmugam <bshanmugam@apm.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This converts the memcpy.S to use the copy template file. The copy
template file was based originally on the memcpy.S
Signed-off-by: NFeng Kan <fkan@apm.com>
Signed-off-by: NBalamurugan Shanmugam <bshanmugam@apm.com>
[catalin.marinas@arm.com: removed tmp3(w) .req statements as they are not used]
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

This patch update defconfig, adds samsung serial and
Synopsys Designware MMC configs related to exynos SoC
Signed-off-by: NAlim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

When function graph tracer is enabled, the following operation
will trigger panic:

mount -t debugfs nodev /sys/kernel
echo next_tgid > /sys/kernel/tracing/set_ftrace_filter
echo function_graph > /sys/kernel/tracing/current_tracer
ls /proc/

------------[ cut here ]------------
[  198.501417] Unable to handle kernel paging request at virtual address cb88537fdc8ba316
[  198.506126] pgd = ffffffc008f79000
[  198.509363] [cb88537fdc8ba316] *pgd=00000000488c6003, *pud=00000000488c6003, *pmd=0000000000000000
[  198.517726] Internal error: Oops: 94000005 [#1] SMP
[  198.518798] Modules linked in:
[  198.520582] CPU: 1 PID: 1388 Comm: ls Tainted: G
[  198.521800] Hardware name: linux,dummy-virt (DT)
[  198.522852] task: ffffffc0fa9e8000 ti: ffffffc0f9ab0000 task.ti: ffffffc0f9ab0000
[  198.524306] PC is at next_tgid+0x30/0x100
[  198.525205] LR is at return_to_handler+0x0/0x20
[  198.526090] pc : [<ffffffc0002a1070>] lr : [<ffffffc0000907c0>] pstate: 60000145
[  198.527392] sp : ffffffc0f9ab3d40
[  198.528084] x29: ffffffc0f9ab3d40 x28: ffffffc0f9ab0000
[  198.529406] x27: ffffffc000d6a000 x26: ffffffc000b786e8
[  198.530659] x25: ffffffc0002a1900 x24: ffffffc0faf16c00
[  198.531942] x23: ffffffc0f9ab3ea0 x22: 0000000000000002
[  198.533202] x21: ffffffc000d85050 x20: 0000000000000002
[  198.534446] x19: 0000000000000002 x18: 0000000000000000
[  198.535719] x17: 000000000049fa08 x16: ffffffc000242efc
[  198.537030] x15: 0000007fa472b54c x14: ffffffffff000000
[  198.538347] x13: ffffffc0fada84a0 x12: 0000000000000001
[  198.539634] x11: ffffffc0f9ab3d70 x10: ffffffc0f9ab3d70
[  198.540915] x9 : ffffffc0000907c0 x8 : ffffffc0f9ab3d40
[  198.542215] x7 : 0000002e330f08f0 x6 : 0000000000000015
[  198.543508] x5 : 0000000000000f08 x4 : ffffffc0f9835ec0
[  198.544792] x3 : cb88537fdc8ba316 x2 : cb88537fdc8ba306
[  198.546108] x1 : 0000000000000002 x0 : ffffffc000d85050
[  198.547432]
[  198.547920] Process ls (pid: 1388, stack limit = 0xffffffc0f9ab0020)
[  198.549170] Stack: (0xffffffc0f9ab3d40 to 0xffffffc0f9ab4000)
[  198.582568] Call trace:
[  198.583313] [<ffffffc0002a1070>] next_tgid+0x30/0x100
[  198.584359] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70
[  198.585503] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70
[  198.586574] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70
[  198.587660] [<ffffffc0000907bc>] ftrace_graph_caller+0x6c/0x70
[  198.588896] Code: aa0003f5 2a0103f4 b4000102 91004043 (885f7c60)
[  198.591092] ---[ end trace 6a346f8f20949ac8 ]---

This is because when using function graph tracer, if the traced
function return value is in multi regs ([x0-x7]), return_to_handler
may corrupt them. So in return_to_handler, the parameter regs should
be protected properly.

Cc: <stable@vger.kernel.org> # 3.18+
Signed-off-by: NLi Bin <huawei.libin@huawei.com>
Acked-by: NAKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

6910fa16 ("arm64: enable PTE type bit in the mask for pte_modify") fixes
a problem whereby a large block of PROT_NONE mapped memory is
incorrectly mapped as block descriptors when mprotect is called.

Unfortunately, a subtle bug was introduced by this fix to the THP logic.

If one mmaps a large block of memory, then faults it such that it is
collapsed into THPs; resulting calls to mprotect on this area of memory
will lead to incorrect table descriptors being written instead of block
descriptors. This is because pmd_modify calls pte_modify which is now
allowed to modify the type of the page table entry.

This patch reverts commit 6910fa16, and
fixes the problem it was trying to address by adjusting PAGE_NONE to
represent a table entry. Thus no change in pte type is required when
moving from PROT_NONE to a different protection.

Fixes: 6910fa16 ("arm64: enable PTE type bit in the mask for pte_modify")
Cc: <stable@vger.kernel.org> # 4.0+
Cc: Feng Kan <fkan@apm.com>
Reported-by: NGanapatrao Kulkarni <Ganapatrao.Kulkarni@caviumnetworks.com>
Tested-by: NGanapatrao Kulkarni <gkulkarni@caviumnetworks.com>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NSteve Capper <steve.capper@linaro.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>

The new Properties Table feature introduced in UEFIv2.5 may
split memory regions that cover PE/COFF memory images into
separate code and data regions. Since these regions only differ
in the type (runtime code vs runtime data) and the permission
bits, but not in the memory type attributes (UC/WC/WT/WB), the
spec does not require them to be aligned to 64 KB.

Since the relative offset of PE/COFF .text and .data segments
cannot be changed on the fly, this means that we can no longer
pad out those regions to be mappable using 64 KB pages.
Unfortunately, there is no annotation in the UEFI memory map
that identifies data regions that were split off from a code
region, so we must apply this logic to all adjacent runtime
regions whose attributes only differ in the permission bits.

So instead of rounding each memory region to 64 KB alignment at
both ends, only round down regions that are not directly
preceded by another runtime region with the same type
attributes. Since the UEFI spec does not mandate that the memory
map be sorted, this means we also need to sort it first.

Note that this change will result in all EFI_MEMORY_RUNTIME
regions whose start addresses are not aligned to the OS page
size to be mapped with executable permissions (i.e., on kernels
compiled with 64 KB pages). However, since these mappings are
only active during the time that UEFI Runtime Services are being
invoked, the window for abuse is rather small.
Tested-by: NMark Salter <msalter@redhat.com>
Tested-by: Mark Rutland <mark.rutland@arm.com> [UEFI 2.4 only]
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
Reviewed-by: NMark Salter <msalter@redhat.com>
Reviewed-by: NMark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org> # v4.0+
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/1443218539-7610-3-git-send-email-matt@codeblueprint.co.ukSigned-off-by: NIngo Molnar <mingo@kernel.org>

We observed some performance degradation on s390x with dynamic
halt polling. Until we can provide a proper fix, let's enable
halt_poll_ns as default only for supported architectures.

Architectures are now free to set their own halt_poll_ns
default value.
Signed-off-by: NDavid Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>

The idle-states bindings mandate that the entry-method string
in the idle-states node must be "psci" for ARM v8 64-bit systems,
but the examples in the bindings report a wrong entry-method string.
Owing to this typo, some dts in the kernel wrongly defined the
entry-method property, since they likely cut and pasted the example
definition without paying attention to the bindings definitions.

This patch fixes the typo in the DT idle states bindings examples and
respective dts in the kernel so that the bindings and related dts
files are made compliant.
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Howard Chen <howard.chen@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: NRob Herring <robh@kernel.org>

This patch removes config option of KVM_ARM_MAX_VCPUS,
and like other ARCHs, just choose the maximum allowed
value from hardware, and follows the reasons:

1) from distribution view, the option has to be
defined as the max allowed value because it need to
meet all kinds of virtulization applications and
need to support most of SoCs;

2) using a bigger value doesn't introduce extra memory
consumption, and the help text in Kconfig isn't accurate
because kvm_vpu structure isn't allocated until request
of creating VCPU is sent from QEMU;

3) the main effect is that the field of vcpus[] in 'struct kvm'
becomes a bit bigger(sizeof(void *) per vcpu) and need more cache
lines to hold the structure, but 'struct kvm' is one generic struct,
and it has worked well on other ARCHs already in this way. Also,
the world switch frequecy is often low, for example, it is ~2000
when running kernel building load in VM from APM xgene KVM host,
so the effect is very small, and the difference can't be observed
in my test at all.

Cc: Dann Frazier <dann.frazier@canonical.com>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Although the ThumbEE registers and traps were present in earlier
versions of the v8 architecture, it was retrospectively removed and so
we can do the same.

Whilst this breaks migrating a guest started on a previous version of
the kernel, it is much better to kill these (non existent) registers
as soon as possible.
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
[maz: added commend about migration]
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

When running a guest with the architected timer disabled (with QEMU and
the kernel_irqchip=off option, for example), it is important to make
sure the timer gets turned off. Otherwise, the guest may try to
enable it anyway, leading to a screaming HW interrupt.

The fix is to unconditionally turn off the virtual timer on guest
exit.

Cc: stable@vger.kernel.org
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>